[U-Boot] [PATCH u-boot] ARM: arch-meson: build memory banks using reported memory from registers
Neil Armstrong
narmstrong at baylibre.com
Sat Nov 25 09:54:31 UTC 2017
Hi Simon,
Le 24/11/2017 23:35, Simon Glass a écrit :
> Hi Neil,
>
> On 20 November 2017 at 08:36, Neil Armstrong <narmstrong at baylibre.com> wrote:
>> As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
>> and a secondary BL32 firmware.
>> Since mid-2017, the reserved memory address of the BL31 firmware was moved
>> and grown for security reasons.
>>
>> But mainline U-boot and Linux has the old address and size fixed.
>
> U-Boot
Damn, I'll try to use U-Boot next times.
>
>>
>> These SoCs have a register interface to get the two firmware reserved
>> memory start and sizes.
>>
>> This patch adds a dynamic reservation of the memory zones in the device tree bootmem
>> reserved memory zone used by the kernel in early boot.
>> To be complete, the memory zones are also added to the EFI reserved zones.
>>
>> Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].
>>
>> [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
>> [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html
>>
>> Changes since RFC v2:
>> - reduced preprocessor load
>> - kept Odroid-C2 static memory mapping as exception
>>
>> Changes since RFC v1:
>> - switch to fdt rsv mem table and efi reserve memory
>> - replaced in_le32 by readl()
>>
>> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
>> ---
>> arch/arm/include/asm/arch-meson/gxbb.h | 17 +++++++
>> arch/arm/mach-meson/board.c | 74 +++++++++++++++++++++++++++----
>> board/amlogic/khadas-vim/khadas-vim.c | 7 +++
>> board/amlogic/libretech-cc/libretech-cc.c | 7 +++
>> board/amlogic/odroid-c2/odroid-c2.c | 7 +++
>> board/amlogic/p212/p212.c | 7 +++
>> configs/khadas-vim_defconfig | 1 +
>> configs/libretech-cc_defconfig | 1 +
>> configs/odroid-c2_defconfig | 1 +
>> configs/p212_defconfig | 1 +
>> include/configs/meson-gxbb-common.h | 2 +-
>> 11 files changed, 116 insertions(+), 9 deletions(-)
>
> Reviewed-by: Simon Glass <sjg at chromium.org>
>
> Various nits/suggestions below.
>
>>
>> diff --git a/arch/arm/include/asm/arch-meson/gxbb.h b/arch/arm/include/asm/arch-meson/gxbb.h
>> index 74d5290..117f796 100644
>> --- a/arch/arm/include/asm/arch-meson/gxbb.h
>> +++ b/arch/arm/include/asm/arch-meson/gxbb.h
>> @@ -7,10 +7,27 @@
>> #ifndef __GXBB_H__
>> #define __GXBB_H__
>>
>> +#define GXBB_FIRMWARE_MEM_SIZE 0x1000000
>> +
>> +#define GXBB_AOBUS_BASE 0xc8100000
>
> Does this not come from the device tree?
Yes it could.
>
>> #define GXBB_PERIPHS_BASE 0xc8834400
>> #define GXBB_HIU_BASE 0xc883c000
>> #define GXBB_ETH_BASE 0xc9410000
>>
>> +/* Always-On Peripherals registers */
>> +#define GXBB_AO_ADDR(off) (GXBB_AOBUS_BASE + ((off) << 2))
>> +
>> +#define GXBB_AO_SEC_GP_CFG0 GXBB_AO_ADDR(0x90)
>> +#define GXBB_AO_SEC_GP_CFG3 GXBB_AO_ADDR(0x93)
>> +#define GXBB_AO_SEC_GP_CFG4 GXBB_AO_ADDR(0x94)
>> +#define GXBB_AO_SEC_GP_CFG5 GXBB_AO_ADDR(0x95)
>> +
>> +#define GXBB_AO_MEM_SIZE_MASK 0xFFFF0000
>> +#define GXBB_AO_MEM_SIZE_SHIFT 16
>> +#define GXBB_AO_BL31_RSVMEM_SIZE_MASK 0xFFFF0000
>> +#define GXBB_AO_BL31_RSVMEM_SIZE_SHIFT 16
>> +#define GXBB_AO_BL32_RSVMEM_SIZE_MASK 0xFFFF
>> +
>> /* Peripherals registers */
>> #define GXBB_PERIPHS_ADDR(off) (GXBB_PERIPHS_BASE + ((off) << 2))
>
> Can you use lower-case hex consistently?
Ok
>
> Also consider a C struct for this peripheral.
Indeed.
>
>>
>> diff --git a/arch/arm/mach-meson/board.c b/arch/arm/mach-meson/board.c
>> index e89c6aa..855614a 100644
>> --- a/arch/arm/mach-meson/board.c
>> +++ b/arch/arm/mach-meson/board.c
>> @@ -11,6 +11,9 @@
>> #include <asm/arch/sm.h>
>> #include <asm/armv8/mmu.h>
>> #include <asm/unaligned.h>
>> +#include <linux/sizes.h>
>> +#include <efi_loader.h>
>> +#include <asm/io.h>
>>
>> DECLARE_GLOBAL_DATA_PTR;
>>
>> @@ -34,15 +37,70 @@ int dram_init(void)
>> return 0;
>> }
>>
>> -int dram_init_banksize(void)
>> +phys_size_t get_effective_memsize(void)
>> {
>> - /* Reserve first 16 MiB of RAM for firmware */
>> - gd->bd->bi_dram[0].start = 0x1000000;
>> - gd->bd->bi_dram[0].size = 0xf000000;
>> - /* Reserve 2 MiB for ARM Trusted Firmware (BL31) */
>> - gd->bd->bi_dram[1].start = 0x10000000;
>> - gd->bd->bi_dram[1].size = gd->ram_size - 0x10200000;
>> - return 0;
>> + /* Size is reported in MiB, convert it in bytes */
>> + return ((readl(GXBB_AO_SEC_GP_CFG0) & GXBB_AO_MEM_SIZE_MASK)
>> + >> GXBB_AO_MEM_SIZE_SHIFT) * SZ_1M;
>> +}
>> +
>> +static void meson_board_add_reserved_memory(void *fdt, u64 start, u64 size)
>> +{
>> + int ret;
>> +
>> + ret = fdt_add_mem_rsv(fdt, start, size);
>> + if (ret)
>> + printf("Could not reserve zone @ 0x%llx\n", start);
>> +
>> +#if defined(CONFIG_EFI_LOADER)
>
> If it possible to do:
>
> if (IS_ENABLED(CONFIG_EFI_LOADER)) {
> ...
>
> That way we don't introduce a new code path for the build.
>
Ok, I'll think about this next times.
>
>> + efi_add_memory_map(start, ALIGN(size, EFI_PAGE_SIZE) >> EFI_PAGE_SHIFT,
>> + EFI_RESERVED_MEMORY_TYPE, false);
>> +#endif
>> +}
>> +
>> +void ft_cpu_setup(void *fdt, bd_t *bd)
>
> I know this is a standard name, but I fell it would be better to name
> it with something containing amlogic so that it is easier to find.
Ok, I just did like other platforms here...
>
>> +{
>> + u64 bl31_size, bl31_start;
>> + u64 bl32_size, bl32_start;
>> + u32 reg;
>> +
>> + /*
>> + * Get ARM Trusted Firmware reserved memory zones in :
>> + * - AO_SEC_GP_CFG3: bl32 & bl31 size in KiB, can be 0
>> + * - AO_SEC_GP_CFG5: bl31 physical start address, can be NULL
>> + * - AO_SEC_GP_CFG4: bl32 physical start address, can be NULL
>> + */
>> +
>> + reg = readl(GXBB_AO_SEC_GP_CFG3);
>> +
>> + bl31_size = ((reg & GXBB_AO_BL31_RSVMEM_SIZE_MASK)
>> + >> GXBB_AO_BL31_RSVMEM_SIZE_SHIFT) * SZ_1K;
>> + bl32_size = (reg & GXBB_AO_BL32_RSVMEM_SIZE_MASK) * SZ_1K;
>> +
>> + bl31_start = readl(GXBB_AO_SEC_GP_CFG5);
>> + bl32_start = readl(GXBB_AO_SEC_GP_CFG4);
>> +
>> + /*
>> + * Early Meson GXBB Firmware revisions did not provide the reserved
>> + * memory zones in the registers, keep fixed memory zone handling.
>> + */
>> +#ifdef CONFIG_MESON_GXBB
>
> Can you use if () ?
Ok
>
>> + if (!reg && !bl31_start && !bl32_start) {
>> + bl31_start = 0x10000000;
>> + bl31_size = 0x200000;
>> + }
>> +#endif
>> +
>> + /* Add first 16MiB reserved zone */
>> + meson_board_add_reserved_memory(fdt, 0, GXBB_FIRMWARE_MEM_SIZE);
>> +
>> + /* Add BL31 reserved zone */
>> + if (bl31_start && bl31_size)
>> + meson_board_add_reserved_memory(fdt, bl31_start, bl31_size);
>> +
>> + /* Add BL32 reserved zone */
>> + if (bl32_start && bl32_size)
>> + meson_board_add_reserved_memory(fdt, bl32_start, bl32_size);
>> }
>>
>> void reset_cpu(ulong addr)
>> diff --git a/board/amlogic/khadas-vim/khadas-vim.c b/board/amlogic/khadas-vim/khadas-vim.c
>> index ece8096..54e31f5 100644
>> --- a/board/amlogic/khadas-vim/khadas-vim.c
>> +++ b/board/amlogic/khadas-vim/khadas-vim.c
>> @@ -56,3 +56,10 @@ int misc_init_r(void)
>>
>> return 0;
>> }
>> +
>> +int ft_board_setup(void *blob, bd_t *bd)
>> +{
>> + ft_cpu_setup(blob, bd);
>> +
>> + return 0;
>> +}
>> diff --git a/board/amlogic/libretech-cc/libretech-cc.c b/board/amlogic/libretech-cc/libretech-cc.c
>> index ece8096..54e31f5 100644
>> --- a/board/amlogic/libretech-cc/libretech-cc.c
>> +++ b/board/amlogic/libretech-cc/libretech-cc.c
>> @@ -56,3 +56,10 @@ int misc_init_r(void)
>>
>> return 0;
>> }
>> +
>> +int ft_board_setup(void *blob, bd_t *bd)
>> +{
>> + ft_cpu_setup(blob, bd);
>> +
>> + return 0;
>> +}
>> diff --git a/board/amlogic/odroid-c2/odroid-c2.c b/board/amlogic/odroid-c2/odroid-c2.c
>> index eac04d8..a9ca34c 100644
>> --- a/board/amlogic/odroid-c2/odroid-c2.c
>> +++ b/board/amlogic/odroid-c2/odroid-c2.c
>> @@ -60,3 +60,10 @@ int misc_init_r(void)
>>
>> return 0;
>> }
>> +
>> +int ft_board_setup(void *blob, bd_t *bd)
>> +{
>> + ft_cpu_setup(blob, bd);
>> +
>> + return 0;
>> +}
>> diff --git a/board/amlogic/p212/p212.c b/board/amlogic/p212/p212.c
>> index ece8096..abd4f76 100644
>> --- a/board/amlogic/p212/p212.c
>> +++ b/board/amlogic/p212/p212.c
>> @@ -56,3 +56,10 @@ int misc_init_r(void)
>>
>> return 0;
>> }
>> +
>> +int ft_board_setup(void *blob, bd_t *bd)
>> +{
>> + ft_cpu_setup(blob, bd);
>> +
>> + return 0;
>> +}
>> diff --git a/configs/khadas-vim_defconfig b/configs/khadas-vim_defconfig
>> index dcccc69..f2a30a8 100644
>> --- a/configs/khadas-vim_defconfig
>> +++ b/configs/khadas-vim_defconfig
>> @@ -17,6 +17,7 @@ CONFIG_CMD_MMC=y
>> CONFIG_CMD_GPIO=y
>> # CONFIG_CMD_SETEXPR is not set
>> CONFIG_OF_CONTROL=y
>> +CONFIG_OF_BOARD_SETUP=y
>> CONFIG_DM_GPIO=y
>> CONFIG_DM_MMC=y
>> CONFIG_MMC_MESON_GX=y
>> diff --git a/configs/libretech-cc_defconfig b/configs/libretech-cc_defconfig
>> index a63e940..6583c43 100644
>> --- a/configs/libretech-cc_defconfig
>> +++ b/configs/libretech-cc_defconfig
>> @@ -17,6 +17,7 @@ CONFIG_CMD_MMC=y
>> CONFIG_CMD_GPIO=y
>> # CONFIG_CMD_SETEXPR is not set
>> CONFIG_OF_CONTROL=y
>> +CONFIG_OF_BOARD_SETUP=y
>> CONFIG_DM_GPIO=y
>> CONFIG_DM_MMC=y
>> CONFIG_MMC_MESON_GX=y
>> diff --git a/configs/odroid-c2_defconfig b/configs/odroid-c2_defconfig
>> index f7f8016..4615e03 100644
>> --- a/configs/odroid-c2_defconfig
>> +++ b/configs/odroid-c2_defconfig
>> @@ -15,6 +15,7 @@ CONFIG_CMD_GPIO=y
>> CONFIG_CMD_MMC=y
>> # CONFIG_CMD_SETEXPR is not set
>> CONFIG_OF_CONTROL=y
>> +CONFIG_OF_BOARD_SETUP=y
>> CONFIG_NET_RANDOM_ETHADDR=y
>> CONFIG_DM_GPIO=y
>> CONFIG_DM_MMC=y
>> diff --git a/configs/p212_defconfig b/configs/p212_defconfig
>> index d4b5349..b6e788b 100644
>> --- a/configs/p212_defconfig
>> +++ b/configs/p212_defconfig
>> @@ -17,6 +17,7 @@ CONFIG_CMD_MMC=y
>> CONFIG_CMD_GPIO=y
>> # CONFIG_CMD_SETEXPR is not set
>> CONFIG_OF_CONTROL=y
>> +CONFIG_OF_BOARD_SETUP=y
>> CONFIG_DM_GPIO=y
>> CONFIG_DM_MMC=y
>> CONFIG_MMC_MESON_GX=y
>> diff --git a/include/configs/meson-gxbb-common.h b/include/configs/meson-gxbb-common.h
>> index d88d42d..c2b306a 100644
>> --- a/include/configs/meson-gxbb-common.h
>> +++ b/include/configs/meson-gxbb-common.h
>> @@ -10,7 +10,7 @@
>>
>> #define CONFIG_CPU_ARMV8
>> #define CONFIG_REMAKE_ELF
>> -#define CONFIG_NR_DRAM_BANKS 2
>> +#define CONFIG_NR_DRAM_BANKS 1
>> #define CONFIG_ENV_SIZE 0x2000
>> #define CONFIG_SYS_MAXARGS 32
>> #define CONFIG_SYS_MALLOC_LEN (32 << 20)
>> --
>> 2.7.4
>>
>
> Regards,
> Simon
>
Thanks,
Neil
More information about the U-Boot
mailing list