[U-Boot] [RFC PATCH 00/13] Nexell S5P6818 SoC support
Andre Przywara
andre.przywara at arm.com
Thu Nov 30 01:24:58 UTC 2017
Hi,
this is a first draft of the things Amit and I have been working on in
the last months. It introduces support for an SoC called "Nexell S5P6818".
This is an Octa-core ARMv8 SoC with Cortex-A53 cores, which apparently is
closely related to (older) Samsung SoCs. Many peripherals are compatible
to Samsung IP (UART, MMC, Ethernet, timers, ...), but some core peripherals
like the clocks and the pin controller seem to be completely different.
We used the NanoPi M3 board [1] for testing, which uses this SoC along with
the usual suspects of on-board components and connectors.
This port is done completely from scratch, by just looking at the manual.
This allows a much cleaner and modern U-Boot support than the BSP code.
The ARM Generic Timer (aka. arch timer) does not seem to work on this SoC.
Ideally there would be some (hidden?) register enabling the right clock
source, though we haven't found one (yet). But as also other code for this
SoC out there on the net does not seem to be able to use the arch timer,
I am not too hopeful here. While this does not impose a real problem to
U-Boot (patch 3/13 takes care of that), it is a showstopper for mainline
arm64 Linux, which heavily relies on the arch timer (since it's a mandatory
part of the ARMv8 architecture). There is only a very small chance that the
arch timer ever becomes optional in the mainline arm64 kernel. However our
arm(32) kernel ports works quite nicely so far, also a (hacked) arm64 kernel
boots to the prompt. We will submit Linux patches at a later time.
We would be grateful to get some comments on the patches.
The first five patches adapt existing code to simplify support for this
SoC. The following six patches then successively enable and add SoC support,
culmulating in the addition of a nanopi_m3_defconfig file in patch 11/13.
The SoC support code is actually architecture agnostic, though up until
the last patch it generates an AArch64 binary. To overcome the problems
with the arch timer mentioned above, the final patch switches the port
over to AArch32, which can more naturally launch arm kernels.
This code so far does not include an SPL, instead it relies on some vendor
provided code to initialise the DRAM and load U-Boot proper. The original
BSP code provided a binary blob for that (called "secondboot"), although
there is some GPLed version of that available on github([2]).
We can load a 32-bit U-Boot with both the vendor blob and Rafaello's GPL
version, the 64-bit version is only usable with the GPL code.
Instruction on how to create a bootable SD card are contained in the
arch/arm/mach-nexell/README file.
We would be very grateful to get some first feedback on those patches
and the approach in general taken here.
Cheers,
Andre.
[1] http://nanopi.io/nanopi-m3.html
[2] https://github.com/rafaello7/bl1-nanopi-m3
Amit Singh Tomar (4):
reset: add driver for generic reset controllers
mmc: add MMC (glue) driver for Nexell SoCs
arm: nexell: add ARM64 MMU regions
arm: nexell: add timer support
Andre Przywara (9):
serial: s5p: rework Samsung UART driver to get rid of uart.h
serial: S5P/Samsung: refactor and Kconfig-ize UART selection
arm: move SYS_ARCH_TIMER to KConfig
arm: add basic framework for Nexell S5P6818 support
arm: nexell: embed NSIH header
arm: nexell: add UART support
arm: nexell: add preliminary S5P6818 SoC device tree
arm: add NanoPi M3 board support
arm: nexell: switch to 32-bit
arch/arm/Kconfig | 29 +++++
arch/arm/Makefile | 1 +
arch/arm/cpu/armv8/Makefile | 2 +-
arch/arm/dts/s5p6818-nanopi-m3.dts | 30 +++++
arch/arm/dts/s5p6818.dtsi | 196 ++++++++++++++++++++++++++++++
arch/arm/dts/s5pc1xx-goni.dts | 2 +-
arch/arm/dts/s5pc1xx-smdkc100.dts | 2 +-
arch/arm/include/asm/arch-nexell/boot0.h | 35 ++++++
arch/arm/include/asm/arch-nexell/clk.h | 15 +++
arch/arm/include/asm/arch-nexell/pwm.h | 62 ++++++++++
arch/arm/mach-exynos/include/mach/uart.h | 44 -------
arch/arm/mach-imx/mx7ulp/Kconfig | 1 +
arch/arm/mach-nexell/Kconfig | 9 ++
arch/arm/mach-nexell/Makefile | 10 ++
arch/arm/mach-nexell/README | 49 ++++++++
arch/arm/mach-nexell/board.c | 128 +++++++++++++++++++
arch/arm/mach-nexell/mmu-arm64.c | 39 ++++++
arch/arm/mach-s5pc1xx/Kconfig | 2 +
arch/arm/mach-s5pc1xx/include/mach/uart.h | 44 -------
configs/nanopi_m3_defconfig | 12 ++
drivers/mmc/Kconfig | 8 ++
drivers/mmc/Makefile | 1 +
drivers/mmc/nexell_dw_mmc.c | 159 ++++++++++++++++++++++++
drivers/reset/Kconfig | 6 +
drivers/reset/Makefile | 1 +
drivers/reset/reset-generic.c | 111 +++++++++++++++++
drivers/serial/Kconfig | 6 +
drivers/serial/Makefile | 2 +-
drivers/serial/serial_s5p.c | 45 ++++++-
include/configs/mx7ulp_evk.h | 1 -
include/configs/s5p6818.h | 35 ++++++
include/configs/ti_armv7_keystone2.h | 1 -
scripts/config_whitelist.txt | 1 -
33 files changed, 989 insertions(+), 100 deletions(-)
create mode 100644 arch/arm/dts/s5p6818-nanopi-m3.dts
create mode 100644 arch/arm/dts/s5p6818.dtsi
create mode 100644 arch/arm/include/asm/arch-nexell/boot0.h
create mode 100644 arch/arm/include/asm/arch-nexell/clk.h
create mode 100644 arch/arm/include/asm/arch-nexell/pwm.h
delete mode 100644 arch/arm/mach-exynos/include/mach/uart.h
create mode 100644 arch/arm/mach-nexell/Kconfig
create mode 100644 arch/arm/mach-nexell/Makefile
create mode 100644 arch/arm/mach-nexell/README
create mode 100644 arch/arm/mach-nexell/board.c
create mode 100644 arch/arm/mach-nexell/mmu-arm64.c
delete mode 100644 arch/arm/mach-s5pc1xx/include/mach/uart.h
create mode 100644 configs/nanopi_m3_defconfig
create mode 100644 drivers/mmc/nexell_dw_mmc.c
create mode 100644 drivers/reset/reset-generic.c
create mode 100644 include/configs/s5p6818.h
--
2.14.1
More information about the U-Boot
mailing list