[U-Boot] [PATCH] tools: Add Marvell recovery image download script

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap at marvell.com>

Introduce the recovery image download script for usage with
Marvell Armada SoC families (excepting 37xx family).
Since Marvell BootROM uses a sliding window in UART buffer
for detecting escape sequence during the boot, it's easier
to interrupt the normal boot flow by sending a long stream
of chained escape sequences to the serial port instead of
periodically sending a single escape sequence as it is done
by kwboot utility.
Additional benefit of using this script is the ability to
adjust the escape sequence stream length withoiut need for
compilation.

Signed-off-by: Konstantin Porotchkin <kostap at marvell.com>
Cc: Stefan Roese <sr at denx.de>
Cc: Igal Liberman <igall at marvell.com>
---
 tools/mrvl_uart.sh | 119 +++++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 119 insertions(+)
 create mode 100755 tools/mrvl_uart.sh

diff --git a/tools/mrvl_uart.sh b/tools/mrvl_uart.sh
new file mode 100755
index 0000000..6b04d7a
--- /dev/null
+++ b/tools/mrvl_uart.sh
@@ -0,0 +1,119 @@
+#!/bin/bash
+#
+######################################################
+# Copyright (C) 2016 Marvell International Ltd.
+#
+# SPDX-License-Identifier:	GPL-2.0
+# https://spdx.org/licenses
+#
+# Author: Konstantin Porotchkin kostap at marvell.com
+#
+# Version 0.3
+#
+# UART recovery downloader for Armada SoCs
+#
+######################################################
+
+port=$1
+file=$2
+speed=$3
+
+pattern_repeat=1500
+default_baudrate=115200
+tmpfile=/tmp/xmodem.pattern
+tools=( dd stty sx minicom )
+
+case "$3" in
+    2)
+        fast_baudrate=230400
+        prefix="\xF2"
+        ;;
+    4)
+        fast_baudrate=460800
+        prefix="\xF4"
+        ;;
+    8)
+    	fast_baudrate=921600
+        prefix="\xF8"
+        ;;
+    *)
+    	fast_baudrate=$default_baudrate
+        prefix="\xBB"
+esac
+
+if [[ -z "$port" || -z "$file" ]]
+then
+    echo -e "\nMarvell recovery image downloader for Armada SoC family."
+    echo -e "Command syntax:"
+    echo -e "\t$(basename $0) <port> <file> [2|4|8]"
+    echo -e "\tport  - serial port the target board connected to"
+    echo -e "\tfile  - recovery boot image for target download"
+    echo -e "\t2|4|8 - times to increase the default serial port speed by"
+    echo -e "For example - load the image over ttyUSB0 @ 460800 baud:"
+    echo -e "$(basename $0) /dev/ttyUSB0 /tmp/flash-image.bin 4\n"
+    echo -e "=====WARNING====="
+    echo -e "- The speed-up option is not awailable in SoC families prior to A8K+"
+    echo -e "- This utility is not compatible with Armada 37xx SoC family\n"
+fi
+
+# Sanity checks
+if [ -c "$port" ]
+then
+   echo -e "Using device connected on serial port \"$port\""
+else
+   echo "Wrong serial port name!"
+   exit 1
+fi
+
+if [ -f "$file" ]
+then
+   echo -e "Loading flash image file \"$file\""
+else
+   echo "File $file does not exist!"
+   exit 1
+fi
+
+# Verify required tools installation
+for tool in ${tools[@]}
+do
+    toolname=`which $tool`
+    if [ -z "$toolname" ]
+    then
+        echo -e "Missing installation of \"$tool\" --> Exiting"
+        exit 1
+    fi
+done
+
+
+echo -e "Recovery will run at $fast_baudrate baud"
+echo -e "========================================"
+
+if [ -f "$tmpfile" ]
+then
+    rm -f $tmpfile
+fi
+
+# Send the escape sequence to target board using default debug port speed
+stty -F $port raw ignbrk time 5 $default_baudrate
+counter=0
+while [ $counter -lt $pattern_repeat ]; do
+    echo -n -e "$prefix\x11\x22\x33\x44\x55\x66\x77" >> $tmpfile
+    let counter=counter+1
+done
+
+echo -en "Press the \"Reset\" button on the target board and "
+echo -en "the \"Enter\" key on the host keyboard simultaneously"
+read
+dd if=$tmpfile of=$port &>/dev/null
+
+# Speed up the binary image transfer
+stty -F $port raw ignbrk time 5 $fast_baudrate
+sx -vv $file > $port < $port
+#sx-at91 $port $file
+
+# return the port to the default speed
+stty -F $port raw ignbrk time 5 $default_baudrate
+
+# Optional - fire up Minicom
+minicom -D $port
+
-- 
2.7.4