[U-Boot] [PATCH 2/6] ARM: rmobile: Move HSUSB configuration to board on Salvator-X

Nobuhiro Iwamatsu iwamatsu at nigauri.org
Fri Sep 22 22:14:43 UTC 2017


Hi,

2017-09-13 2:07 GMT+09:00 Marek Vasut <marek.vasut at gmail.com>:
> In order to use ehci-generic driver, move the configuration of HSUSB
> block into the board file. This configuration should not have been in
> the Gen3 EHCI USB driver in the first place, so move it to the board
> file until there is a proper infrastructure and driver for the HSUSB
> block.
>
> Signed-off-by: Marek Vasut <marek.vasut+renesas at gmail.com>
> Cc: Nobuhiro Iwamatsu <iwamatsu at nigauri.org>

Applied to rmobile branch.

Thanks,
  Nobuhiro

> ---
>  board/renesas/salvator-x/salvator-x.c | 16 ++++++++++++++++
>  1 file changed, 16 insertions(+)
>
> diff --git a/board/renesas/salvator-x/salvator-x.c b/board/renesas/salvator-x/salvator-x.c
> index e260117802..37fcbbd448 100644
> --- a/board/renesas/salvator-x/salvator-x.c
> +++ b/board/renesas/salvator-x/salvator-x.c
> @@ -55,6 +55,7 @@ void s_init(void)
>  #define SD1_MSTP313            BIT(13)
>  #define SD2_MSTP312            BIT(12) /* either MMC0 */
>  #define SD3_MSTP311            BIT(11) /* either MMC1 */
> +#define HSUSB_MSTP704          BIT(4)  /* HSUSB */
>
>  #define SD0CKCR                        0xE6150074
>  #define SD1CKCR                        0xE6150078
> @@ -92,6 +93,13 @@ int board_early_init_f(void)
>  /* -/W 32 Power resume control register 2 (3DG) */
>  #define        SYSC_PWRONCR2   0xE618010C
>
> +/* HSUSB block registers */
> +#define HSUSB_REG_LPSTS                        0xE6590102
> +#define HSUSB_REG_LPSTS_SUSPM_NORMAL   BIT(14)
> +#define HSUSB_REG_UGCTRL2              0xE6590184
> +#define HSUSB_REG_UGCTRL2_USB0SEL      0x30
> +#define HSUSB_REG_UGCTRL2_USB0SEL_EHCI 0x10
> +
>  int board_init(void)
>  {
>         /* adress of boot parameters */
> @@ -116,6 +124,14 @@ int board_init(void)
>         /* USB1 pull-up */
>         setbits_le32(PFC_PUEN6, PUEN_USB1_OVC | PUEN_USB1_PWEN);
>
> +       /* Configure the HSUSB block */
> +       mstp_clrbits_le32(MSTPSR7, SMSTPCR7, HSUSB_MSTP704);
> +       /* Choice USB0SEL */
> +       clrsetbits_le32(HSUSB_REG_UGCTRL2, HSUSB_REG_UGCTRL2_USB0SEL,
> +                       HSUSB_REG_UGCTRL2_USB0SEL_EHCI);
> +       /* low power status */
> +       setbits_le16(HSUSB_REG_LPSTS, HSUSB_REG_LPSTS_SUSPM_NORMAL);
> +
>  #ifdef CONFIG_RENESAS_RAVB
>         /* EtherAVB Enable */
>         /* GPSR2 */
> --
> 2.11.0
>



-- 
Nobuhiro Iwamatsu
   iwamatsu at {nigauri.org / debian.org}
   GPG ID: 40AD1FA6


More information about the U-Boot mailing list