[U-Boot] [U-Boot, v2, 2/5] power: pmic: rk816: support rk816 pmic
Dr. Philipp Tomsich
philipp.tomsich at theobroma-systems.com
Thu Sep 28 10:39:44 UTC 2017
Kever,
> On 28 Sep 2017, at 12:12, Kever Yang <kever.yang at rock-chips.com> wrote:
>
> Hi Philipp,
>
> On 09/28/2017 04:47 PM, Philipp Tomsich wrote:
>>
>>
>> On Wed, 27 Sep 2017, Kever Yang wrote:
>>
>>> From: Elaine Zhang <zhangqing at rock-chips.com> <mailto:zhangqing at rock-chips.com>
>>>
>>> Add Rockchip pmic rk816 support.
>>>
>>> RK816 have 4 DCDC, 6 LDO, RTC, CHARGER, FUEL GAUGE, GPIO, PWRKEY.
>>> The DCDC and LDO voltage output range and current loading are different
>>> from RK808 and RK818.
>>> RK816 add mask bit for enable/disable for read/write safety.
>>>
>>> The RK816 most used with rk312x/rk322x/rk332x SoCs.
>>>
>>> Signed-off-by: Elaine Zhang <zhangqing at rock-chips.com> <mailto:zhangqing at rock-chips.com>
>>> Signed-off-by: Kever Yang <kever.yang at rock-chips.com> <mailto:kever.yang at rock-chips.com>
>>
>> The changes I requested (https://patchwork.ozlabs.org/patch/813297/ <https://patchwork.ozlabs.org/patch/813297/>) to to split this up (so we avoid having different logic in a switch/case for every function have not been addressed).
>>
>> The RK816 apparently is different enough from the RK808 and RK816 to warrant a separate DM driver.
>>
>> Our basic rule-of-thumb for deciding when to split a driver should be whether the new device can be added using driverdata containing parameters or whether we end up adding new conditional and exclusive code-paths (i.e. if there's a conditional statement in the middle that just adds/removes one step of processing, when this certainly won't justify splitting a driver) to the overwhelming number of the ops.
>>
>> Please split this to introduce a new driver for the RK816 and keep the existing driver as simple as it is today.
>
> I have reply your comment in patch set V1, and explain why we think it's reason-able
> to make then in one driver instead of two. What you are asking is not like to keep code clean and less duplicate code.
> I copy my comment here again, I prefer to improve the implementation instead of split them into different driver.
I had seen the comment (patchworks picked it up and I keep checking there to make sure I didn’t miss emails).
However, I disagree: see below.
> Will add detail difference between these chips, they are very similar as
> regulator and it's reasonable to make then in one driver instead of use different
> drivers for them:
> - different DCDC/LDO numbers;
> - different voltage output range and current loading;
> - RK816 and RK805 add mask bit for enable/disable to make read/write
> more safe.
> The framework and the setting for all these chips are the same, except
> the BUCK/LDO numbers are different, and rk805/rk816 need extra mask bit for
> enable/disable.
In these cases, we should have a file containing the common code and then mini-drivers that use them.
I had the same discussion with Simon, when I tried to get the rk3399 hdmi merged—and we finally decided
there on using the model of having small DM-drivers that have the different logic and then using shared
functions for the shared infrastructure
> Abstract the difference into array structure is a good way to share the
> code, I don't think split this into rk805.c rk808.c rk816.c and rk818.c will have a
> better shape.
The array structure is great (and I very much like how it’s done), but the changed implementation concerns
me. Let’s look at _buck_set_enable as an example…
Initially it had a very clean flow (pseudocode):
{
if (enable)
/* set/clear a few bits */
return /* another op */;
}
Now it has morphed into:
{
switch (id) {
case ONE_CHIP:
if (enable)
/* set/clear some bits */
ret = /* another op */
break;
case ANOTHER_CHIP:
if (enable)
/* set/clear some bits */
ret = /* other ops */;
break;
default:
/* handle a bad id */
}
return ret;
}
This is clearly a case where multiple different functions should be used… and normally another
DM-driver will be called for.
Note that there is also a runtime penalty (the compiler can’t optimise the switch-statemenet away)
and a size penalty (important, as regulator-drivers may be needed as early as TPL).
> BTW, these are all the PMICs we have since early 2013, so don't worry,
> it won't grow into large switch statement.
That’s good to hear ;-)
However, this is yet another reason why this should be a separate mini-driver…
For the time being, I’ll pick up the remainder of the series for rc1 and we can then sort out how
to deal with this specific driver after the upcoming golden week?
> Thanks,
> - Kever
>>
>>> ---
>>>
>>> Changes in v2:
>>> - add introduce info for RK816 in commit message
>>>
>>> drivers/power/pmic/rk8xx.c | 1 +
>>> drivers/power/regulator/rk8xx.c | 212 ++++++++++++++++++++++++++++++++--------
>>> include/power/rk8xx_pmic.h | 9 +-
>>> 3 files changed, 182 insertions(+), 40 deletions(-)
>>>
>>> diff --git a/drivers/power/pmic/rk8xx.c b/drivers/power/pmic/rk8xx.c
>>> index eb3ec0f..0fdea95 100644
>>> --- a/drivers/power/pmic/rk8xx.c
>>> +++ b/drivers/power/pmic/rk8xx.c
>>> @@ -100,6 +100,7 @@ static struct dm_pmic_ops rk8xx_ops = {
>>>
>>> static const struct udevice_id rk8xx_ids[] = {
>>> { .compatible = "rockchip,rk808" },
>>> + { .compatible = "rockchip,rk816" },
>>> { .compatible = "rockchip,rk818" },
>>> { }
>>> };
>>> diff --git a/drivers/power/regulator/rk8xx.c b/drivers/power/regulator/rk8xx.c
>>> index 76fc2ef..cf3566e 100644
>>> --- a/drivers/power/regulator/rk8xx.c
>>> +++ b/drivers/power/regulator/rk8xx.c
>>> @@ -48,6 +48,21 @@ static const struct rk8xx_reg_info rk808_buck[] = {
>>> { 1800000, 100000, REG_BUCK4_ON_VSEL, RK808_BUCK4_VSEL_MASK, },
>>> };
>>>
>>> +static const struct rk8xx_reg_info rk816_buck[] = {
>>> + /* buck 1 */
>>> + { 712500, 12500, REG_BUCK1_ON_VSEL, RK818_BUCK_VSEL_MASK, },
>>> + { 1800000, 200000, REG_BUCK1_ON_VSEL, RK818_BUCK_VSEL_MASK, },
>>> + { 2300000, 0, REG_BUCK1_ON_VSEL, RK818_BUCK_VSEL_MASK, },
>>> + /* buck 2 */
>>> + { 712500, 12500, REG_BUCK2_ON_VSEL, RK818_BUCK_VSEL_MASK, },
>>> + { 1800000, 200000, REG_BUCK2_ON_VSEL, RK818_BUCK_VSEL_MASK, },
>>> + { 2300000, 0, REG_BUCK2_ON_VSEL, RK818_BUCK_VSEL_MASK, },
>>> + /* buck 3 */
>>> + { 712500, 12500, -1, RK818_BUCK_VSEL_MASK, },
>>> + /* buck 4 */
>>> + { 800000, 100000, REG_BUCK4_ON_VSEL, RK818_BUCK4_VSEL_MASK, },
>>> +};
>>> +
>>> static const struct rk8xx_reg_info rk818_buck[] = {
>>> { 712500, 12500, REG_BUCK1_ON_VSEL, RK818_BUCK_VSEL_MASK, },
>>> { 712500, 12500, REG_BUCK2_ON_VSEL, RK818_BUCK_VSEL_MASK, },
>>> @@ -67,6 +82,15 @@ static const struct rk8xx_reg_info rk808_ldo[] = {
>>> { 1800000, 100000, REG_LDO8_ON_VSEL, RK808_LDO_VSEL_MASK, },
>>> };
>>>
>>> +static const struct rk8xx_reg_info rk816_ldo[] = {
>>> + { 800000, 100000, REG_LDO1_ON_VSEL, RK818_LDO_VSEL_MASK, },
>>> + { 800000, 100000, REG_LDO2_ON_VSEL, RK818_LDO_VSEL_MASK, },
>>> + { 800000, 100000, REG_LDO3_ON_VSEL, RK818_LDO_VSEL_MASK, },
>>> + { 800000, 100000, REG_LDO4_ON_VSEL, RK818_LDO_VSEL_MASK, },
>>> + { 800000, 100000, REG_LDO5_ON_VSEL, RK818_LDO_VSEL_MASK, },
>>> + { 800000, 100000, REG_LDO6_ON_VSEL, RK818_LDO_VSEL_MASK, },
>>> +};
>>> +
>>> static const struct rk8xx_reg_info rk818_ldo[] = {
>>> { 1800000, 100000, REG_LDO1_ON_VSEL, RK818_LDO_VSEL_MASK, },
>>> { 1800000, 100000, REG_LDO2_ON_VSEL, RK818_LDO_VSEL_MASK, },
>>> @@ -88,10 +112,24 @@ static const uint rk818_chrg_shutdown_vsel_array[] = {
>>> };
>>>
>>> static const struct rk8xx_reg_info *get_buck_reg(struct udevice *pmic,
>>> - int num)
>>> + int num, int uvolt)
>>> {
>>> struct rk8xx_priv *priv = dev_get_priv(pmic);
>>> +
>>> switch (priv->variant) {
>>> + case RK816_ID:
>>> + switch (num) {
>>> + case 0:
>>> + case 1:
>>> + if (uvolt <= 1450000)
>>> + return &rk816_buck[num * 3 + 0];
>>> + else if (uvolt <= 2200000)
>>> + return &rk816_buck[num * 3 + 1];
>>> + else
>>> + return &rk816_buck[num * 3 + 2];
>>> + default:
>>> + return &rk816_buck[num + 4];
>>> + }
>>> case RK818_ID:
>>> return &rk818_buck[num];
>>> default:
>>> @@ -101,7 +139,7 @@ static const struct rk8xx_reg_info *get_buck_reg(struct udevice *pmic,
>>>
>>> static int _buck_set_value(struct udevice *pmic, int buck, int uvolt)
>>> {
>>> - const struct rk8xx_reg_info *info = get_buck_reg(pmic, buck - 1);
>>> + const struct rk8xx_reg_info *info = get_buck_reg(pmic, buck, uvolt);
>>> int mask = info->vsel_mask;
>>> int val;
>>>
>>> @@ -114,23 +152,76 @@ static int _buck_set_value(struct udevice *pmic, int buck, int uvolt)
>>> return pmic_clrsetbits(pmic, info->vsel_reg, mask, val);
>>> }
>>>
>>> +static int _buck_get_enable(struct udevice *pmic, int buck)
>>> +{
>>> + struct rk8xx_priv *priv = dev_get_priv(pmic);
>>> + uint mask = 0;
>>> + int ret = 0;
>>> +
>>> + switch (priv->variant) {
>>> + case RK816_ID:
>>> + if (buck >= 4) {
>>> + mask = 1 << (buck - 4);
>>> + ret = pmic_reg_read(pmic, RK816_REG_DCDC_EN2);
>>> + } else {
>>> + mask = 1 << buck;
>>> + ret = pmic_reg_read(pmic, RK816_REG_DCDC_EN1);
>>> + }
>>> + break;
>>> + case RK808_ID:
>>> + case RK818_ID:
>>> + mask = 1 << buck;
>>> + ret = pmic_reg_read(pmic, REG_DCDC_EN);
>>> + if (ret < 0)
>>> + return ret;
>>> + break;
>>> + }
>>> + return ret & mask ? true : false;
>>> +}
>>> +
>>> +
>>> static int _buck_set_enable(struct udevice *pmic, int buck, bool enable)
>>> {
>>> - uint mask;
>>> + uint mask, value, en_reg;
>>> int ret;
>>> + struct rk8xx_priv *priv = dev_get_priv(pmic);
>>>
>>> - buck--;
>>> - mask = 1 << buck;
>>> - if (enable) {
>>> - ret = pmic_clrsetbits(pmic, REG_DCDC_ILMAX, 0, 3 << (buck * 2));
>>> - if (ret)
>>> - return ret;
>>> - ret = pmic_clrsetbits(pmic, REG_DCDC_UV_ACT, 1 << buck, 0);
>>> - if (ret)
>>> - return ret;
>>> + switch (priv->variant) {
>>> + case RK816_ID:
>>> + if (buck >= 4) {
>>> + buck -= 4;
>>> + en_reg = RK816_REG_DCDC_EN2;
>>> + } else {
>>> + en_reg = RK816_REG_DCDC_EN1;
>>> + }
>>> + if (enable)
>>> + value = ((1 << buck) | (1 << (buck + 4)));
>>> + else
>>> + value = ((0 << buck) | (1 << (buck + 4)));
>>> + ret = pmic_reg_write(pmic, en_reg, value);
>>> + break;
>>> +
>>> + case RK808_ID:
>>> + case RK818_ID:
>>> + mask = 1 << buck;
>>> + if (enable) {
>>> + ret = pmic_clrsetbits(pmic, REG_DCDC_ILMAX,
>>> + 0, 3 << (buck * 2));
>>> + if (ret)
>>> + return ret;
>>> + ret = pmic_clrsetbits(pmic, REG_DCDC_UV_ACT,
>>> + 1 << buck, 0);
>>> + if (ret)
>>> + return ret;
>>> + }
>>> + ret = pmic_clrsetbits(pmic, REG_DCDC_EN, mask,
>>> + enable ? mask : 0);
>>> + break;
>>> + default:
>>> + ret = -EINVAL;
>>> }
>>>
>>> - return pmic_clrsetbits(pmic, REG_DCDC_EN, mask, enable ? mask : 0);
>>> + return ret;
>>> }
>>>
>>> #ifdef ENABLE_DRIVER
>>> @@ -138,7 +229,10 @@ static const struct rk8xx_reg_info *get_ldo_reg(struct udevice *pmic,
>>> int num)
>>> {
>>> struct rk8xx_priv *priv = dev_get_priv(pmic);
>>> +
>>> switch (priv->variant) {
>>> + case RK816_ID:
>>> + return &rk816_ldo[num];
>>> case RK818_ID:
>>> return &rk818_ldo[num];
>>> default:
>>> @@ -146,10 +240,70 @@ static const struct rk8xx_reg_info *get_ldo_reg(struct udevice *pmic,
>>> }
>>> }
>>>
>>> +static int _ldo_get_enable(struct udevice *pmic, int ldo)
>>> +{
>>> + struct rk8xx_priv *priv = dev_get_priv(pmic);
>>> + uint mask = 0;
>>> + int ret = 0;
>>> +
>>> + switch (priv->variant) {
>>> + case RK816_ID:
>>> + if (ldo >= 4) {
>>> + mask = 1 << (ldo - 4);
>>> + ret = pmic_reg_read(pmic, RK816_REG_LDO_EN2);
>>> + } else {
>>> + mask = 1 << ldo;
>>> + ret = pmic_reg_read(pmic, RK816_REG_LDO_EN1);
>>> + }
>>> + break;
>>> + case RK808_ID:
>>> + case RK818_ID:
>>> + mask = 1 << ldo;
>>> + ret = pmic_reg_read(pmic, REG_LDO_EN);
>>> + if (ret < 0)
>>> + return ret;
>>> + break;
>>> + }
>>> + return ret & mask ? true : false;
>>> +}
>>> +
>>> +
>>> +static int _ldo_set_enable(struct udevice *pmic, int ldo, bool enable)
>>> +{
>>> + struct rk8xx_priv *priv = dev_get_priv(pmic);
>>> + uint mask, value, en_reg;
>>> + int ret = 0;
>>> +
>>> + switch (priv->variant) {
>>> + case RK816_ID:
>>> + if (ldo >= 4) {
>>> + ldo -= 4;
>>> + en_reg = RK816_REG_LDO_EN2;
>>> + } else {
>>> + en_reg = RK816_REG_LDO_EN1;
>>> + }
>>> + if (enable)
>>> + value = ((1 << ldo) | (1 << (ldo + 4)));
>>> + else
>>> + value = ((0 << ldo) | (1 << (ldo + 4)));
>>> +
>>> + ret = pmic_reg_write(pmic, en_reg, value);
>>> + break;
>>> + case RK808_ID:
>>> + case RK818_ID:
>>> + mask = 1 << ldo;
>>> + ret = pmic_clrsetbits(pmic, REG_LDO_EN, mask,
>>> + enable ? mask : 0);
>>> + break;
>>> + }
>>> +
>>> + return ret;
>>> +}
>>> +
>>> static int buck_get_value(struct udevice *dev)
>>> {
>>> int buck = dev->driver_data - 1;
>>> - const struct rk8xx_reg_info *info = get_buck_reg(dev->parent, buck);
>>> + const struct rk8xx_reg_info *info = get_buck_reg(dev->parent, buck, 0);
>>> int mask = info->vsel_mask;
>>> int ret, val;
>>>
>>> @@ -165,14 +319,14 @@ static int buck_get_value(struct udevice *dev)
>>>
>>> static int buck_set_value(struct udevice *dev, int uvolt)
>>> {
>>> - int buck = dev->driver_data;
>>> + int buck = dev->driver_data - 1;
>>>
>>> return _buck_set_value(dev->parent, buck, uvolt);
>>> }
>>>
>>> static int buck_set_enable(struct udevice *dev, bool enable)
>>> {
>>> - int buck = dev->driver_data;
>>> + int buck = dev->driver_data - 1;
>>>
>>> return _buck_set_enable(dev->parent, buck, enable);
>>> }
>>> @@ -180,16 +334,8 @@ static int buck_set_enable(struct udevice *dev, bool enable)
>>> static int buck_get_enable(struct udevice *dev)
>>> {
>>> int buck = dev->driver_data - 1;
>>> - int ret;
>>> - uint mask;
>>> -
>>> - mask = 1 << buck;
>>>
>>> - ret = pmic_reg_read(dev->parent, REG_DCDC_EN);
>>> - if (ret < 0)
>>> - return ret;
>>> -
>>> - return ret & mask ? true : false;
>>> + return _buck_get_enable(dev->parent, buck);
>>> }
>>>
>>> static int ldo_get_value(struct udevice *dev)
>>> @@ -228,27 +374,15 @@ static int ldo_set_value(struct udevice *dev, int uvolt)
>>> static int ldo_set_enable(struct udevice *dev, bool enable)
>>> {
>>> int ldo = dev->driver_data - 1;
>>> - uint mask;
>>> -
>>> - mask = 1 << ldo;
>>>
>>> - return pmic_clrsetbits(dev->parent, REG_LDO_EN, mask,
>>> - enable ? mask : 0);
>>> + return _ldo_set_enable(dev->parent, ldo, enable);
>>> }
>>>
>>> static int ldo_get_enable(struct udevice *dev)
>>> {
>>> int ldo = dev->driver_data - 1;
>>> - int ret;
>>> - uint mask;
>>> -
>>> - mask = 1 << ldo;
>>>
>>> - ret = pmic_reg_read(dev->parent, REG_LDO_EN);
>>> - if (ret < 0)
>>> - return ret;
>>> -
>>> - return ret & mask ? true : false;
>>> + return _ldo_get_enable(dev->parent, ldo);
>>> }
>>>
>>> static int switch_set_enable(struct udevice *dev, bool enable)
>>> diff --git a/include/power/rk8xx_pmic.h b/include/power/rk8xx_pmic.h
>>> index 47a6b36..8e821c3 100644
>>> --- a/include/power/rk8xx_pmic.h
>>> +++ b/include/power/rk8xx_pmic.h
>>> @@ -171,8 +171,15 @@ enum {
>>> };
>>>
>>> enum {
>>> - RK805_ID = 0x8050,
>>> + RK816_REG_DCDC_EN1 = 0x23,
>>> + RK816_REG_DCDC_EN2,
>>> + RK816_REG_LDO_EN1 = 0x27,
>>> + RK816_REG_LDO_EN2,
>>> +};
>>> +
>>> +enum {
>>> RK808_ID = 0x0000,
>>> + RK816_ID = 0x8160,
>>> RK818_ID = 0x8180,
>>> };
>>>
>>>
>>
>
More information about the U-Boot
mailing list