[U-Boot] [PATCH v6 09/27] mtd: move NAND files into a raw/ subdirectory
Miquel Raynal
miquel.raynal at bootlin.com
Wed Aug 1 08:18:30 UTC 2018
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Documentation, README*, and MAINTAINERS files are updated accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal at bootlin.com>
---
MAINTAINERS | 6 +-
Makefile | 2 +-
README | 6 +-
arch/arm/mach-uniphier/board_late_init.c | 2 +-
common/spl/Kconfig | 2 +-
common/spl/spl_spi.c | 2 +-
doc/README.SPL | 4 +-
doc/README.arm-relocation | 2 +-
doc/README.nand | 6 +-
doc/README.zynq | 2 +-
drivers/Makefile | 2 +-
drivers/mtd/Makefile | 2 +
drivers/mtd/nand/Kconfig | 298 +-------------------------
drivers/mtd/nand/Makefile | 75 -------
drivers/mtd/nand/raw/Kconfig | 297 +++++++++++++++++++++++++
drivers/mtd/nand/raw/Makefile | 77 +++++++
drivers/mtd/nand/{ => raw}/am335x_spl_bch.c | 0
drivers/mtd/nand/{ => raw}/arasan_nfc.c | 0
drivers/mtd/nand/{ => raw}/atmel_nand.c | 0
drivers/mtd/nand/{ => raw}/atmel_nand_ecc.h | 0
drivers/mtd/nand/{ => raw}/davinci_nand.c | 2 +-
drivers/mtd/nand/{ => raw}/denali.c | 0
drivers/mtd/nand/{ => raw}/denali.h | 0
drivers/mtd/nand/{ => raw}/denali_dt.c | 0
drivers/mtd/nand/{ => raw}/denali_spl.c | 0
drivers/mtd/nand/{ => raw}/fsl_elbc_nand.c | 0
drivers/mtd/nand/{ => raw}/fsl_elbc_spl.c | 0
drivers/mtd/nand/{ => raw}/fsl_ifc_nand.c | 0
drivers/mtd/nand/{ => raw}/fsl_ifc_spl.c | 0
drivers/mtd/nand/{ => raw}/fsl_upm.c | 0
drivers/mtd/nand/{ => raw}/fsmc_nand.c | 0
drivers/mtd/nand/{ => raw}/kb9202_nand.c | 0
drivers/mtd/nand/{ => raw}/kirkwood_nand.c | 0
drivers/mtd/nand/{ => raw}/kmeter1_nand.c | 0
drivers/mtd/nand/{ => raw}/lpc32xx_nand_mlc.c | 0
drivers/mtd/nand/{ => raw}/lpc32xx_nand_slc.c | 0
drivers/mtd/nand/{ => raw}/mxc_nand.c | 0
drivers/mtd/nand/{ => raw}/mxc_nand.h | 0
drivers/mtd/nand/{ => raw}/mxc_nand_spl.c | 0
drivers/mtd/nand/{ => raw}/mxs_nand.c | 0
drivers/mtd/nand/{ => raw}/mxs_nand.h | 0
drivers/mtd/nand/{ => raw}/mxs_nand_dt.c | 0
drivers/mtd/nand/{ => raw}/mxs_nand_spl.c | 0
drivers/mtd/nand/{ => raw}/nand.c | 0
drivers/mtd/nand/{ => raw}/nand_base.c | 0
drivers/mtd/nand/{ => raw}/nand_bbt.c | 0
drivers/mtd/nand/{ => raw}/nand_bch.c | 0
drivers/mtd/nand/{ => raw}/nand_ecc.c | 2 +-
drivers/mtd/nand/{ => raw}/nand_ids.c | 0
drivers/mtd/nand/{ => raw}/nand_plat.c | 0
drivers/mtd/nand/{ => raw}/nand_spl_load.c | 0
drivers/mtd/nand/{ => raw}/nand_spl_loaders.c | 0
drivers/mtd/nand/{ => raw}/nand_spl_simple.c | 0
drivers/mtd/nand/{ => raw}/nand_timings.c | 0
drivers/mtd/nand/{ => raw}/nand_util.c | 2 +-
drivers/mtd/nand/{ => raw}/omap_elm.c | 0
drivers/mtd/nand/{ => raw}/omap_gpmc.c | 0
drivers/mtd/nand/{ => raw}/pxa3xx_nand.c | 2 +-
drivers/mtd/nand/{ => raw}/pxa3xx_nand.h | 0
drivers/mtd/nand/{ => raw}/sunxi_nand.c | 0
drivers/mtd/nand/{ => raw}/sunxi_nand_spl.c | 0
drivers/mtd/nand/{ => raw}/tegra_nand.c | 0
drivers/mtd/nand/{ => raw}/tegra_nand.h | 0
drivers/mtd/nand/{ => raw}/vf610_nfc.c | 0
drivers/mtd/nand/{ => raw}/zynq_nand.c | 0
include/configs/MPC8313ERDB.h | 2 +-
66 files changed, 400 insertions(+), 395 deletions(-)
create mode 100644 drivers/mtd/nand/raw/Kconfig
create mode 100644 drivers/mtd/nand/raw/Makefile
rename drivers/mtd/nand/{ => raw}/am335x_spl_bch.c (100%)
rename drivers/mtd/nand/{ => raw}/arasan_nfc.c (100%)
rename drivers/mtd/nand/{ => raw}/atmel_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/atmel_nand_ecc.h (100%)
rename drivers/mtd/nand/{ => raw}/davinci_nand.c (99%)
rename drivers/mtd/nand/{ => raw}/denali.c (100%)
rename drivers/mtd/nand/{ => raw}/denali.h (100%)
rename drivers/mtd/nand/{ => raw}/denali_dt.c (100%)
rename drivers/mtd/nand/{ => raw}/denali_spl.c (100%)
rename drivers/mtd/nand/{ => raw}/fsl_elbc_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/fsl_elbc_spl.c (100%)
rename drivers/mtd/nand/{ => raw}/fsl_ifc_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/fsl_ifc_spl.c (100%)
rename drivers/mtd/nand/{ => raw}/fsl_upm.c (100%)
rename drivers/mtd/nand/{ => raw}/fsmc_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/kb9202_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/kirkwood_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/kmeter1_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/lpc32xx_nand_mlc.c (100%)
rename drivers/mtd/nand/{ => raw}/lpc32xx_nand_slc.c (100%)
rename drivers/mtd/nand/{ => raw}/mxc_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/mxc_nand.h (100%)
rename drivers/mtd/nand/{ => raw}/mxc_nand_spl.c (100%)
rename drivers/mtd/nand/{ => raw}/mxs_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/mxs_nand.h (100%)
rename drivers/mtd/nand/{ => raw}/mxs_nand_dt.c (100%)
rename drivers/mtd/nand/{ => raw}/mxs_nand_spl.c (100%)
rename drivers/mtd/nand/{ => raw}/nand.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_base.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_bbt.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_bch.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_ecc.c (99%)
rename drivers/mtd/nand/{ => raw}/nand_ids.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_plat.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_spl_load.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_spl_loaders.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_spl_simple.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_timings.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_util.c (99%)
rename drivers/mtd/nand/{ => raw}/omap_elm.c (100%)
rename drivers/mtd/nand/{ => raw}/omap_gpmc.c (100%)
rename drivers/mtd/nand/{ => raw}/pxa3xx_nand.c (99%)
rename drivers/mtd/nand/{ => raw}/pxa3xx_nand.h (100%)
rename drivers/mtd/nand/{ => raw}/sunxi_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/sunxi_nand_spl.c (100%)
rename drivers/mtd/nand/{ => raw}/tegra_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/tegra_nand.h (100%)
rename drivers/mtd/nand/{ => raw}/vf610_nfc.c (100%)
rename drivers/mtd/nand/{ => raw}/zynq_nand.c (100%)
diff --git a/MAINTAINERS b/MAINTAINERS
index e44280ceb6..63f2457494 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -281,7 +281,7 @@ F: drivers/i2c/i2c-cdns.c
F: drivers/i2c/muxes/pca954x.c
F: drivers/i2c/zynq_i2c.c
F: drivers/mmc/zynq_sdhci.c
-F: drivers/mtd/nand/zynq_nand.c
+F: drivers/mtd/nand/raw/zynq_nand.c
F: drivers/net/phy/xilinx_phy.c
F: drivers/net/zynq_gem.c
F: drivers/serial/serial_zynq.c
@@ -305,7 +305,7 @@ F: drivers/i2c/i2c-cdns.c
F: drivers/i2c/muxes/pca954x.c
F: drivers/i2c/zynq_i2c.c
F: drivers/mmc/zynq_sdhci.c
-F: drivers/mtd/nand/zynq_nand.c
+F: drivers/mtd/nand/raw/zynq_nand.c
F: drivers/net/phy/xilinx_phy.c
F: drivers/net/zynq_gem.c
F: drivers/serial/serial_zynq.c
@@ -440,7 +440,7 @@ NAND FLASH
#M: Scott Wood <oss at buserror.net>
S: Orphaned (Since 2018-07)
T: git git://git.denx.de/u-boot-nand-flash.git
-F: drivers/mtd/nand/
+F: drivers/mtd/nand/raw/
NDS32
M: Macpaul Lin <macpaul at andestech.com>
diff --git a/Makefile b/Makefile
index 675d011c95..a54bffb3ef 100644
--- a/Makefile
+++ b/Makefile
@@ -685,7 +685,7 @@ libs-y += drivers/dma/
libs-y += drivers/gpio/
libs-y += drivers/i2c/
libs-y += drivers/mtd/
-libs-$(CONFIG_CMD_NAND) += drivers/mtd/nand/
+libs-$(CONFIG_CMD_NAND) += drivers/mtd/nand/raw/
libs-y += drivers/mtd/onenand/
libs-$(CONFIG_CMD_UBI) += drivers/mtd/ubi/
libs-y += drivers/mtd/spi/
diff --git a/README b/README
index aee0f7371c..fd5034ce91 100644
--- a/README
+++ b/README
@@ -3264,8 +3264,8 @@ Low Level (hardware related) configuration options:
a 16 bit bus.
Not all NAND drivers use this symbol.
Example of drivers that use it:
- - drivers/mtd/nand/ndfc.c
- - drivers/mtd/nand/mxc_nand.c
+ - drivers/mtd/nand/raw/ndfc.c
+ - drivers/mtd/nand/raw/mxc_nand.c
- CONFIG_SYS_NDFC_EBC0_CFG
Sets the EBC0_CFG register for the NDFC. If not defined
@@ -3382,7 +3382,7 @@ Low Level (hardware related) configuration options:
- CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
Option to disable subpage write in NAND driver
driver that uses this:
- drivers/mtd/nand/davinci_nand.c
+ drivers/mtd/nand/raw/davinci_nand.c
Freescale QE/FMAN Firmware Support:
-----------------------------------
diff --git a/arch/arm/mach-uniphier/board_late_init.c b/arch/arm/mach-uniphier/board_late_init.c
index 8ffb9a8d3c..1b871c62ce 100644
--- a/arch/arm/mach-uniphier/board_late_init.c
+++ b/arch/arm/mach-uniphier/board_late_init.c
@@ -12,7 +12,7 @@
#include <stdio.h>
#include <linux/io.h>
#include <linux/printk.h>
-#include <../drivers/mtd/nand/denali.h>
+#include <../drivers/mtd/nand/raw/denali.h>
#include "init.h"
diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index 2af26a881a..7bf7a23542 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -479,7 +479,7 @@ config SPL_NAND_SUPPORT
help
Enable support for NAND (Negative AND) flash in SPL. NAND flash
can be used to allow SPL to load U-Boot from supported devices.
- This enables the drivers in drivers/mtd/nand as part of an SPL
+ This enables the drivers in drivers/mtd/nand/raw as part of an SPL
build.
config SPL_NET_SUPPORT
diff --git a/common/spl/spl_spi.c b/common/spl/spl_spi.c
index ba60a3a3c5..0016d49739 100644
--- a/common/spl/spl_spi.c
+++ b/common/spl/spl_spi.c
@@ -2,7 +2,7 @@
/*
* Copyright (C) 2011 OMICRON electronics GmbH
*
- * based on drivers/mtd/nand/nand_spl_load.c
+ * based on drivers/mtd/nand/raw/nand_spl_load.c
*
* Copyright (C) 2011
* Heiko Schocher, DENX Software Engineering, hs at denx.de.
diff --git a/doc/README.SPL b/doc/README.SPL
index 3ba313caa8..fc1ca1ad4f 100644
--- a/doc/README.SPL
+++ b/doc/README.SPL
@@ -57,11 +57,11 @@ CONFIG_SPL_FAT_SUPPORT (fs/fat/libfat.o)
CONFIG_SPL_EXT_SUPPORT
CONFIG_SPL_LIBGENERIC_SUPPORT (lib/libgeneric.o)
CONFIG_SPL_POWER_SUPPORT (drivers/power/libpower.o)
-CONFIG_SPL_NAND_SUPPORT (drivers/mtd/nand/libnand.o)
+CONFIG_SPL_NAND_SUPPORT (drivers/mtd/nand/raw/libnand.o)
CONFIG_SPL_DRIVERS_MISC_SUPPORT (drivers/misc)
CONFIG_SPL_DMA_SUPPORT (drivers/dma/libdma.o)
CONFIG_SPL_POST_MEM_SUPPORT (post/drivers/memory.o)
-CONFIG_SPL_NAND_LOAD (drivers/mtd/nand/nand_spl_load.o)
+CONFIG_SPL_NAND_LOAD (drivers/mtd/nand/raw/nand_spl_load.o)
CONFIG_SPL_SPI_LOAD (drivers/mtd/spi/spi_spl_load.o)
CONFIG_SPL_RAM_DEVICE (common/spl/spl.c)
CONFIG_SPL_WATCHDOG_SUPPORT (drivers/watchdog/libwatchdog.o)
diff --git a/doc/README.arm-relocation b/doc/README.arm-relocation
index 645b3746c8..d2a7e8122e 100644
--- a/doc/README.arm-relocation
+++ b/doc/README.arm-relocation
@@ -84,7 +84,7 @@ Relocation with SPL (example for the tx25 booting from NAND Flash):
- cpu copies the first page from NAND to 0xbb000000 (IMX_NFC_BASE)
and start with code execution on this address.
-- The First page contains u-boot code from drivers/mtd/nand/mxc_nand_spl.c
+- The First page contains u-boot code from drivers/mtd/nand/raw/mxc_nand_spl.c
which inits the dram, cpu registers, reloacte itself to CONFIG_SPL_TEXT_BASE and loads
the "real" u-boot to CONFIG_SYS_NAND_U_BOOT_DST and starts execution
@CONFIG_SYS_NAND_U_BOOT_START
diff --git a/doc/README.nand b/doc/README.nand
index cda11b43ff..ec461b2dc9 100644
--- a/doc/README.nand
+++ b/doc/README.nand
@@ -116,7 +116,7 @@ Configuration Options:
The maximum number of NAND chips per device to be supported.
CONFIG_SYS_NAND_SELF_INIT
- Traditionally, glue code in drivers/mtd/nand/nand.c has driven
+ Traditionally, glue code in drivers/mtd/nand/raw/nand.c has driven
the initialization process -- it provides the mtd and nand
structs, calls a board init function for a specific device,
calls nand_scan(), and registers with mtd.
@@ -125,7 +125,7 @@ Configuration Options:
run code between nand_scan_ident() and nand_scan_tail(), or other
deviations from the "normal" flow.
- If a board defines CONFIG_SYS_NAND_SELF_INIT, drivers/mtd/nand/nand.c
+ If a board defines CONFIG_SYS_NAND_SELF_INIT, drivers/mtd/nand/raw/nand.c
will make one call to board_nand_init(), with no arguments. That
function is responsible for calling a driver init function for
each NAND device on the board, that performs all initialization
@@ -280,7 +280,7 @@ NOTE:
=====
The Disk On Chip driver is currently broken and has been for some time.
-There is a driver in drivers/mtd/nand, taken from Linux, that works with
+There is a driver in drivers/mtd/nand/raw, taken from Linux, that works with
the current NAND system but has not yet been adapted to the u-boot
environment.
diff --git a/doc/README.zynq b/doc/README.zynq
index 5b0672c503..da977b2016 100644
--- a/doc/README.zynq
+++ b/doc/README.zynq
@@ -63,7 +63,7 @@ bootmode strings at runtime.
spi - drivers/spi/zynq_spi.c
qspi - drivers/spi/zynq_qspi.c
i2c - drivers/i2c/zynq_i2c.c
- nand - drivers/mtd/nand/zynq_nand.c
+ nand - drivers/mtd/nand/raw/zynq_nand.c
- Done proper cleanups on board configurations
- Added basic FDT support for zynq boards
- d-cache support for zynq_gem.c
diff --git a/drivers/Makefile b/drivers/Makefile
index 276e5ee4d7..ccd1b648d0 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -6,7 +6,7 @@ obj-$(CONFIG_$(SPL_TPL_)DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
obj-$(CONFIG_$(SPL_TPL_)I2C_SUPPORT) += i2c/
obj-$(CONFIG_$(SPL_TPL_)LED) += led/
obj-$(CONFIG_$(SPL_TPL_)MMC_SUPPORT) += mmc/
-obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += mtd/nand/
+obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += mtd/nand/raw/
obj-$(CONFIG_$(SPL_TPL_)PHY) += phy/
obj-$(CONFIG_$(SPL_TPL_)PINCTRL) += pinctrl/
obj-$(CONFIG_$(SPL_TPL_)RAM) += ram/
diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
index 9cec06510c..cdf515256a 100644
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -18,3 +18,5 @@ obj-$(CONFIG_FLASH_PIC32) += pic32_flash.o
obj-$(CONFIG_ST_SMI) += st_smi.o
obj-$(CONFIG_STM32_FLASH) += stm32_flash.o
obj-$(CONFIG_RENESAS_RPC_HF) += renesas_rpc_hf.o
+
+obj-y += nand/
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 1e4ea7bdd4..6d53734718 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -1,297 +1 @@
-
-menuconfig NAND
- bool "NAND Device Support"
-if NAND
-
-config SYS_NAND_SELF_INIT
- bool
- help
- This option, if enabled, provides more flexible and linux-like
- NAND initialization process.
-
-config NAND_ATMEL
- bool "Support Atmel NAND controller"
- imply SYS_NAND_USE_FLASH_BBT
- help
- Enable this driver for NAND flash platforms using an Atmel NAND
- controller.
-
-config NAND_DAVINCI
- bool "Support TI Davinci NAND controller"
- help
- Enable this driver for NAND flash controllers available in TI Davinci
- and Keystone2 platforms
-
-config NAND_DENALI
- bool
- select SYS_NAND_SELF_INIT
- imply CMD_NAND
-
-config NAND_DENALI_DT
- bool "Support Denali NAND controller as a DT device"
- select NAND_DENALI
- depends on OF_CONTROL && DM
- help
- Enable the driver for NAND flash on platforms using a Denali NAND
- controller as a DT device.
-
-config NAND_DENALI_SPARE_AREA_SKIP_BYTES
- int "Number of bytes skipped in OOB area"
- depends on NAND_DENALI
- range 0 63
- help
- This option specifies the number of bytes to skip from the beginning
- of OOB area before last ECC sector data starts. This is potentially
- used to preserve the bad block marker in the OOB area.
-
-config NAND_LPC32XX_SLC
- bool "Support LPC32XX_SLC controller"
- help
- Enable the LPC32XX SLC NAND controller.
-
-config NAND_OMAP_GPMC
- bool "Support OMAP GPMC NAND controller"
- depends on ARCH_OMAP2PLUS
- help
- Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms.
- GPMC controller is used for parallel NAND flash devices, and can
- do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8
- and BCH16 ECC algorithms.
-
-config NAND_OMAP_GPMC_PREFETCH
- bool "Enable GPMC Prefetch"
- depends on NAND_OMAP_GPMC
- default y
- help
- On OMAP platforms that use the GPMC controller
- (CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that
- uses the prefetch mode to speed up read operations.
-
-config NAND_OMAP_ELM
- bool "Enable ELM driver for OMAPxx and AMxx platforms."
- depends on NAND_OMAP_GPMC && !OMAP34XX
- help
- ELM controller is used for ECC error detection (not ECC calculation)
- of BCH4, BCH8 and BCH16 ECC algorithms.
- Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
- thus such SoC platforms need to depend on software library for ECC error
- detection. However ECC calculation on such plaforms would still be
- done by GPMC controller.
-
-config NAND_VF610_NFC
- bool "Support for Freescale NFC for VF610"
- select SYS_NAND_SELF_INIT
- imply CMD_NAND
- help
- Enables support for NAND Flash Controller on some Freescale
- processors like the VF610, MCF54418 or Kinetis K70.
- The driver supports a maximum 2k page size. The driver
- currently does not support hardware ECC.
-
-choice
- prompt "Hardware ECC strength"
- depends on NAND_VF610_NFC
- default SYS_NAND_VF610_NFC_45_ECC_BYTES
- help
- Select the ECC strength used in the hardware BCH ECC block.
-
-config SYS_NAND_VF610_NFC_45_ECC_BYTES
- bool "24-error correction (45 ECC bytes)"
-
-config SYS_NAND_VF610_NFC_60_ECC_BYTES
- bool "32-error correction (60 ECC bytes)"
-
-endchoice
-
-config NAND_PXA3XX
- bool "Support for NAND on PXA3xx and Armada 370/XP/38x"
- select SYS_NAND_SELF_INIT
- imply CMD_NAND
- help
- This enables the driver for the NAND flash device found on
- PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
-
-config NAND_SUNXI
- bool "Support for NAND on Allwinner SoCs"
- default ARCH_SUNXI
- depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I
- select SYS_NAND_SELF_INIT
- select SYS_NAND_U_BOOT_LOCATIONS
- select SPL_NAND_SUPPORT
- imply CMD_NAND
- ---help---
- Enable support for NAND. This option enables the standard and
- SPL drivers.
- The SPL driver only supports reading from the NAND using DMA
- transfers.
-
-if NAND_SUNXI
-
-config NAND_SUNXI_SPL_ECC_STRENGTH
- int "Allwinner NAND SPL ECC Strength"
- default 64
-
-config NAND_SUNXI_SPL_ECC_SIZE
- int "Allwinner NAND SPL ECC Step Size"
- default 1024
-
-config NAND_SUNXI_SPL_USABLE_PAGE_SIZE
- int "Allwinner NAND SPL Usable Page Size"
- default 1024
-
-endif
-
-config NAND_ARASAN
- bool "Configure Arasan Nand"
- select SYS_NAND_SELF_INIT
- imply CMD_NAND
- help
- This enables Nand driver support for Arasan nand flash
- controller. This uses the hardware ECC for read and
- write operations.
-
-config NAND_MXC
- bool "MXC NAND support"
- depends on CPU_ARM926EJS || CPU_ARM1136 || MX5
- imply CMD_NAND
- help
- This enables the NAND driver for the NAND flash controller on the
- i.MX27 / i.MX31 / i.MX5 rocessors.
-
-config NAND_MXS
- bool "MXS NAND support"
- depends on MX23 || MX28 || MX6 || MX7
- select SYS_NAND_SELF_INIT
- imply CMD_NAND
- select APBH_DMA
- select APBH_DMA_BURST if ARCH_MX6 || ARCH_MX7
- select APBH_DMA_BURST8 if ARCH_MX6 || ARCH_MX7
- help
- This enables NAND driver for the NAND flash controller on the
- MXS processors.
-
-if NAND_MXS
-
-config NAND_MXS_DT
- bool "Support MXS NAND controller as a DT device"
- depends on OF_CONTROL && MTD
- help
- Enable the driver for MXS NAND flash on platforms using
- device tree.
-
-config NAND_MXS_USE_MINIMUM_ECC
- bool "Use minimum ECC strength supported by the controller"
- default false
-
-endif
-
-config NAND_ZYNQ
- bool "Support for Zynq Nand controller"
- select SYS_NAND_SELF_INIT
- imply CMD_NAND
- help
- This enables Nand driver support for Nand flash controller
- found on Zynq SoC.
-
-config NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS
- bool "Enable use of 1st stage bootloader timing for NAND"
- depends on NAND_ZYNQ
- help
- This flag prevent U-boot reconfigure NAND flash controller and reuse
- the NAND timing from 1st stage bootloader.
-
-comment "Generic NAND options"
-
-config SYS_NAND_BLOCK_SIZE
- hex "NAND chip eraseblock size"
- depends on ARCH_SUNXI
- help
- Number of data bytes in one eraseblock for the NAND chip on the
- board. This is the multiple of NAND_PAGE_SIZE and the number of
- pages.
-
-config SYS_NAND_PAGE_SIZE
- hex "NAND chip page size"
- depends on ARCH_SUNXI
- help
- Number of data bytes in one page for the NAND chip on the
- board, not including the OOB area.
-
-config SYS_NAND_OOBSIZE
- hex "NAND chip OOB size"
- depends on ARCH_SUNXI
- help
- Number of bytes in the Out-Of-Band area for the NAND chip on
- the board.
-
-# Enhance depends when converting drivers to Kconfig which use this config
-# option (mxc_nand, ndfc, omap_gpmc).
-config SYS_NAND_BUSWIDTH_16BIT
- bool "Use 16-bit NAND interface"
- depends on NAND_VF610_NFC || NAND_OMAP_GPMC || NAND_MXC || ARCH_DAVINCI
- help
- Indicates that NAND device has 16-bit wide data-bus. In absence of this
- config, bus-width of NAND device is assumed to be either 8-bit and later
- determined by reading ONFI params.
- Above config is useful when NAND device's bus-width information cannot
- be determined from on-chip ONFI params, like in following scenarios:
- - SPL boot does not support reading of ONFI parameters. This is done to
- keep SPL code foot-print small.
- - In current U-Boot flow using nand_init(), driver initialization
- happens in board_nand_init() which is called before any device probe
- (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are
- not available while configuring controller. So a static CONFIG_NAND_xx
- is needed to know the device's bus-width in advance.
-
-if SPL
-
-config SYS_NAND_U_BOOT_LOCATIONS
- bool "Define U-boot binaries locations in NAND"
- help
- Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig.
- This option should not be enabled when compiling U-boot for boards
- defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h
- file.
-
-config SYS_NAND_U_BOOT_OFFS
- hex "Location in NAND to read U-Boot from"
- default 0x800000 if NAND_SUNXI
- depends on SYS_NAND_U_BOOT_LOCATIONS
- help
- Set the offset from the start of the nand where u-boot should be
- loaded from.
-
-config SYS_NAND_U_BOOT_OFFS_REDUND
- hex "Location in NAND to read U-Boot from"
- default SYS_NAND_U_BOOT_OFFS
- depends on SYS_NAND_U_BOOT_LOCATIONS
- help
- Set the offset from the start of the nand where the redundant u-boot
- should be loaded from.
-
-config SPL_NAND_AM33XX_BCH
- bool "Enables SPL-NAND driver which supports ELM based"
- depends on NAND_OMAP_GPMC && !OMAP34XX
- default y
- help
- Hardware ECC correction. This is useful for platforms which have ELM
- hardware engine and use NAND boot mode.
- Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
- so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling
- SPL-NAND driver with software ECC correction support.
-
-config SPL_NAND_DENALI
- bool "Support Denali NAND controller for SPL"
- help
- This is a small implementation of the Denali NAND controller
- for use on SPL.
-
-config SPL_NAND_SIMPLE
- bool "Use simple SPL NAND driver"
- depends on !SPL_NAND_AM33XX_BCH
- help
- Support for NAND boot using simple NAND drivers that
- expose the cmd_ctrl() interface.
-endif
-
-endif # if NAND
+source "drivers/mtd/nand/raw/Kconfig"
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index c61e3f3839..69f40d1563 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -1,77 +1,2 @@
# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-ifdef CONFIG_SPL_BUILD
-
-ifdef CONFIG_SPL_NAND_DRIVERS
-NORMAL_DRIVERS=y
-endif
-
-obj-$(CONFIG_SPL_NAND_AM33XX_BCH) += am335x_spl_bch.o
-obj-$(CONFIG_SPL_NAND_DENALI) += denali_spl.o
-obj-$(CONFIG_SPL_NAND_SIMPLE) += nand_spl_simple.o
-obj-$(CONFIG_SPL_NAND_LOAD) += nand_spl_load.o
-obj-$(CONFIG_SPL_NAND_ECC) += nand_ecc.o
-obj-$(CONFIG_SPL_NAND_BASE) += nand_base.o
-obj-$(CONFIG_SPL_NAND_IDENT) += nand_ids.o nand_timings.o
-obj-$(CONFIG_SPL_NAND_INIT) += nand.o
-ifeq ($(CONFIG_SPL_ENV_SUPPORT),y)
-obj-$(CONFIG_ENV_IS_IN_NAND) += nand_util.o
-endif
-
-else # not spl
-
-NORMAL_DRIVERS=y
-
-obj-y += nand.o
-obj-y += nand_bbt.o
-obj-y += nand_ids.o
-obj-y += nand_util.o
-obj-y += nand_ecc.o
-obj-y += nand_base.o
-obj-y += nand_timings.o
-
-endif # not spl
-
-ifdef NORMAL_DRIVERS
-
-obj-$(CONFIG_NAND_ECC_BCH) += nand_bch.o
-
-obj-$(CONFIG_NAND_ATMEL) += atmel_nand.o
-obj-$(CONFIG_NAND_ARASAN) += arasan_nfc.o
-obj-$(CONFIG_NAND_DAVINCI) += davinci_nand.o
-obj-$(CONFIG_NAND_DENALI) += denali.o
-obj-$(CONFIG_NAND_DENALI_DT) += denali_dt.o
-obj-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o
-obj-$(CONFIG_NAND_FSL_IFC) += fsl_ifc_nand.o
-obj-$(CONFIG_NAND_FSL_UPM) += fsl_upm.o
-obj-$(CONFIG_NAND_FSMC) += fsmc_nand.o
-obj-$(CONFIG_NAND_KB9202) += kb9202_nand.o
-obj-$(CONFIG_NAND_KIRKWOOD) += kirkwood_nand.o
-obj-$(CONFIG_NAND_KMETER1) += kmeter1_nand.o
-obj-$(CONFIG_NAND_LPC32XX_MLC) += lpc32xx_nand_mlc.o
-obj-$(CONFIG_NAND_LPC32XX_SLC) += lpc32xx_nand_slc.o
-obj-$(CONFIG_NAND_VF610_NFC) += vf610_nfc.o
-obj-$(CONFIG_NAND_MXC) += mxc_nand.o
-obj-$(CONFIG_NAND_MXS) += mxs_nand.o
-obj-$(CONFIG_NAND_MXS_DT) += mxs_nand_dt.o
-obj-$(CONFIG_NAND_PXA3XX) += pxa3xx_nand.o
-obj-$(CONFIG_NAND_SPEAR) += spr_nand.o
-obj-$(CONFIG_TEGRA_NAND) += tegra_nand.o
-obj-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o
-obj-$(CONFIG_NAND_OMAP_ELM) += omap_elm.o
-obj-$(CONFIG_NAND_PLAT) += nand_plat.o
-obj-$(CONFIG_NAND_SUNXI) += sunxi_nand.o
-obj-$(CONFIG_NAND_ZYNQ) += zynq_nand.o
-
-else # minimal SPL drivers
-
-obj-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_spl.o
-obj-$(CONFIG_NAND_FSL_IFC) += fsl_ifc_spl.o
-obj-$(CONFIG_NAND_MXC) += mxc_nand_spl.o
-obj-$(CONFIG_NAND_MXS) += mxs_nand_spl.o mxs_nand.o
-obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o
-
-endif # drivers
diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
new file mode 100644
index 0000000000..1e4ea7bdd4
--- /dev/null
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -0,0 +1,297 @@
+
+menuconfig NAND
+ bool "NAND Device Support"
+if NAND
+
+config SYS_NAND_SELF_INIT
+ bool
+ help
+ This option, if enabled, provides more flexible and linux-like
+ NAND initialization process.
+
+config NAND_ATMEL
+ bool "Support Atmel NAND controller"
+ imply SYS_NAND_USE_FLASH_BBT
+ help
+ Enable this driver for NAND flash platforms using an Atmel NAND
+ controller.
+
+config NAND_DAVINCI
+ bool "Support TI Davinci NAND controller"
+ help
+ Enable this driver for NAND flash controllers available in TI Davinci
+ and Keystone2 platforms
+
+config NAND_DENALI
+ bool
+ select SYS_NAND_SELF_INIT
+ imply CMD_NAND
+
+config NAND_DENALI_DT
+ bool "Support Denali NAND controller as a DT device"
+ select NAND_DENALI
+ depends on OF_CONTROL && DM
+ help
+ Enable the driver for NAND flash on platforms using a Denali NAND
+ controller as a DT device.
+
+config NAND_DENALI_SPARE_AREA_SKIP_BYTES
+ int "Number of bytes skipped in OOB area"
+ depends on NAND_DENALI
+ range 0 63
+ help
+ This option specifies the number of bytes to skip from the beginning
+ of OOB area before last ECC sector data starts. This is potentially
+ used to preserve the bad block marker in the OOB area.
+
+config NAND_LPC32XX_SLC
+ bool "Support LPC32XX_SLC controller"
+ help
+ Enable the LPC32XX SLC NAND controller.
+
+config NAND_OMAP_GPMC
+ bool "Support OMAP GPMC NAND controller"
+ depends on ARCH_OMAP2PLUS
+ help
+ Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms.
+ GPMC controller is used for parallel NAND flash devices, and can
+ do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8
+ and BCH16 ECC algorithms.
+
+config NAND_OMAP_GPMC_PREFETCH
+ bool "Enable GPMC Prefetch"
+ depends on NAND_OMAP_GPMC
+ default y
+ help
+ On OMAP platforms that use the GPMC controller
+ (CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that
+ uses the prefetch mode to speed up read operations.
+
+config NAND_OMAP_ELM
+ bool "Enable ELM driver for OMAPxx and AMxx platforms."
+ depends on NAND_OMAP_GPMC && !OMAP34XX
+ help
+ ELM controller is used for ECC error detection (not ECC calculation)
+ of BCH4, BCH8 and BCH16 ECC algorithms.
+ Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
+ thus such SoC platforms need to depend on software library for ECC error
+ detection. However ECC calculation on such plaforms would still be
+ done by GPMC controller.
+
+config NAND_VF610_NFC
+ bool "Support for Freescale NFC for VF610"
+ select SYS_NAND_SELF_INIT
+ imply CMD_NAND
+ help
+ Enables support for NAND Flash Controller on some Freescale
+ processors like the VF610, MCF54418 or Kinetis K70.
+ The driver supports a maximum 2k page size. The driver
+ currently does not support hardware ECC.
+
+choice
+ prompt "Hardware ECC strength"
+ depends on NAND_VF610_NFC
+ default SYS_NAND_VF610_NFC_45_ECC_BYTES
+ help
+ Select the ECC strength used in the hardware BCH ECC block.
+
+config SYS_NAND_VF610_NFC_45_ECC_BYTES
+ bool "24-error correction (45 ECC bytes)"
+
+config SYS_NAND_VF610_NFC_60_ECC_BYTES
+ bool "32-error correction (60 ECC bytes)"
+
+endchoice
+
+config NAND_PXA3XX
+ bool "Support for NAND on PXA3xx and Armada 370/XP/38x"
+ select SYS_NAND_SELF_INIT
+ imply CMD_NAND
+ help
+ This enables the driver for the NAND flash device found on
+ PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
+
+config NAND_SUNXI
+ bool "Support for NAND on Allwinner SoCs"
+ default ARCH_SUNXI
+ depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I
+ select SYS_NAND_SELF_INIT
+ select SYS_NAND_U_BOOT_LOCATIONS
+ select SPL_NAND_SUPPORT
+ imply CMD_NAND
+ ---help---
+ Enable support for NAND. This option enables the standard and
+ SPL drivers.
+ The SPL driver only supports reading from the NAND using DMA
+ transfers.
+
+if NAND_SUNXI
+
+config NAND_SUNXI_SPL_ECC_STRENGTH
+ int "Allwinner NAND SPL ECC Strength"
+ default 64
+
+config NAND_SUNXI_SPL_ECC_SIZE
+ int "Allwinner NAND SPL ECC Step Size"
+ default 1024
+
+config NAND_SUNXI_SPL_USABLE_PAGE_SIZE
+ int "Allwinner NAND SPL Usable Page Size"
+ default 1024
+
+endif
+
+config NAND_ARASAN
+ bool "Configure Arasan Nand"
+ select SYS_NAND_SELF_INIT
+ imply CMD_NAND
+ help
+ This enables Nand driver support for Arasan nand flash
+ controller. This uses the hardware ECC for read and
+ write operations.
+
+config NAND_MXC
+ bool "MXC NAND support"
+ depends on CPU_ARM926EJS || CPU_ARM1136 || MX5
+ imply CMD_NAND
+ help
+ This enables the NAND driver for the NAND flash controller on the
+ i.MX27 / i.MX31 / i.MX5 rocessors.
+
+config NAND_MXS
+ bool "MXS NAND support"
+ depends on MX23 || MX28 || MX6 || MX7
+ select SYS_NAND_SELF_INIT
+ imply CMD_NAND
+ select APBH_DMA
+ select APBH_DMA_BURST if ARCH_MX6 || ARCH_MX7
+ select APBH_DMA_BURST8 if ARCH_MX6 || ARCH_MX7
+ help
+ This enables NAND driver for the NAND flash controller on the
+ MXS processors.
+
+if NAND_MXS
+
+config NAND_MXS_DT
+ bool "Support MXS NAND controller as a DT device"
+ depends on OF_CONTROL && MTD
+ help
+ Enable the driver for MXS NAND flash on platforms using
+ device tree.
+
+config NAND_MXS_USE_MINIMUM_ECC
+ bool "Use minimum ECC strength supported by the controller"
+ default false
+
+endif
+
+config NAND_ZYNQ
+ bool "Support for Zynq Nand controller"
+ select SYS_NAND_SELF_INIT
+ imply CMD_NAND
+ help
+ This enables Nand driver support for Nand flash controller
+ found on Zynq SoC.
+
+config NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS
+ bool "Enable use of 1st stage bootloader timing for NAND"
+ depends on NAND_ZYNQ
+ help
+ This flag prevent U-boot reconfigure NAND flash controller and reuse
+ the NAND timing from 1st stage bootloader.
+
+comment "Generic NAND options"
+
+config SYS_NAND_BLOCK_SIZE
+ hex "NAND chip eraseblock size"
+ depends on ARCH_SUNXI
+ help
+ Number of data bytes in one eraseblock for the NAND chip on the
+ board. This is the multiple of NAND_PAGE_SIZE and the number of
+ pages.
+
+config SYS_NAND_PAGE_SIZE
+ hex "NAND chip page size"
+ depends on ARCH_SUNXI
+ help
+ Number of data bytes in one page for the NAND chip on the
+ board, not including the OOB area.
+
+config SYS_NAND_OOBSIZE
+ hex "NAND chip OOB size"
+ depends on ARCH_SUNXI
+ help
+ Number of bytes in the Out-Of-Band area for the NAND chip on
+ the board.
+
+# Enhance depends when converting drivers to Kconfig which use this config
+# option (mxc_nand, ndfc, omap_gpmc).
+config SYS_NAND_BUSWIDTH_16BIT
+ bool "Use 16-bit NAND interface"
+ depends on NAND_VF610_NFC || NAND_OMAP_GPMC || NAND_MXC || ARCH_DAVINCI
+ help
+ Indicates that NAND device has 16-bit wide data-bus. In absence of this
+ config, bus-width of NAND device is assumed to be either 8-bit and later
+ determined by reading ONFI params.
+ Above config is useful when NAND device's bus-width information cannot
+ be determined from on-chip ONFI params, like in following scenarios:
+ - SPL boot does not support reading of ONFI parameters. This is done to
+ keep SPL code foot-print small.
+ - In current U-Boot flow using nand_init(), driver initialization
+ happens in board_nand_init() which is called before any device probe
+ (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are
+ not available while configuring controller. So a static CONFIG_NAND_xx
+ is needed to know the device's bus-width in advance.
+
+if SPL
+
+config SYS_NAND_U_BOOT_LOCATIONS
+ bool "Define U-boot binaries locations in NAND"
+ help
+ Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig.
+ This option should not be enabled when compiling U-boot for boards
+ defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h
+ file.
+
+config SYS_NAND_U_BOOT_OFFS
+ hex "Location in NAND to read U-Boot from"
+ default 0x800000 if NAND_SUNXI
+ depends on SYS_NAND_U_BOOT_LOCATIONS
+ help
+ Set the offset from the start of the nand where u-boot should be
+ loaded from.
+
+config SYS_NAND_U_BOOT_OFFS_REDUND
+ hex "Location in NAND to read U-Boot from"
+ default SYS_NAND_U_BOOT_OFFS
+ depends on SYS_NAND_U_BOOT_LOCATIONS
+ help
+ Set the offset from the start of the nand where the redundant u-boot
+ should be loaded from.
+
+config SPL_NAND_AM33XX_BCH
+ bool "Enables SPL-NAND driver which supports ELM based"
+ depends on NAND_OMAP_GPMC && !OMAP34XX
+ default y
+ help
+ Hardware ECC correction. This is useful for platforms which have ELM
+ hardware engine and use NAND boot mode.
+ Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
+ so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling
+ SPL-NAND driver with software ECC correction support.
+
+config SPL_NAND_DENALI
+ bool "Support Denali NAND controller for SPL"
+ help
+ This is a small implementation of the Denali NAND controller
+ for use on SPL.
+
+config SPL_NAND_SIMPLE
+ bool "Use simple SPL NAND driver"
+ depends on !SPL_NAND_AM33XX_BCH
+ help
+ Support for NAND boot using simple NAND drivers that
+ expose the cmd_ctrl() interface.
+endif
+
+endif # if NAND
diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
new file mode 100644
index 0000000000..c61e3f3839
--- /dev/null
+++ b/drivers/mtd/nand/raw/Makefile
@@ -0,0 +1,77 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+
+ifdef CONFIG_SPL_BUILD
+
+ifdef CONFIG_SPL_NAND_DRIVERS
+NORMAL_DRIVERS=y
+endif
+
+obj-$(CONFIG_SPL_NAND_AM33XX_BCH) += am335x_spl_bch.o
+obj-$(CONFIG_SPL_NAND_DENALI) += denali_spl.o
+obj-$(CONFIG_SPL_NAND_SIMPLE) += nand_spl_simple.o
+obj-$(CONFIG_SPL_NAND_LOAD) += nand_spl_load.o
+obj-$(CONFIG_SPL_NAND_ECC) += nand_ecc.o
+obj-$(CONFIG_SPL_NAND_BASE) += nand_base.o
+obj-$(CONFIG_SPL_NAND_IDENT) += nand_ids.o nand_timings.o
+obj-$(CONFIG_SPL_NAND_INIT) += nand.o
+ifeq ($(CONFIG_SPL_ENV_SUPPORT),y)
+obj-$(CONFIG_ENV_IS_IN_NAND) += nand_util.o
+endif
+
+else # not spl
+
+NORMAL_DRIVERS=y
+
+obj-y += nand.o
+obj-y += nand_bbt.o
+obj-y += nand_ids.o
+obj-y += nand_util.o
+obj-y += nand_ecc.o
+obj-y += nand_base.o
+obj-y += nand_timings.o
+
+endif # not spl
+
+ifdef NORMAL_DRIVERS
+
+obj-$(CONFIG_NAND_ECC_BCH) += nand_bch.o
+
+obj-$(CONFIG_NAND_ATMEL) += atmel_nand.o
+obj-$(CONFIG_NAND_ARASAN) += arasan_nfc.o
+obj-$(CONFIG_NAND_DAVINCI) += davinci_nand.o
+obj-$(CONFIG_NAND_DENALI) += denali.o
+obj-$(CONFIG_NAND_DENALI_DT) += denali_dt.o
+obj-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o
+obj-$(CONFIG_NAND_FSL_IFC) += fsl_ifc_nand.o
+obj-$(CONFIG_NAND_FSL_UPM) += fsl_upm.o
+obj-$(CONFIG_NAND_FSMC) += fsmc_nand.o
+obj-$(CONFIG_NAND_KB9202) += kb9202_nand.o
+obj-$(CONFIG_NAND_KIRKWOOD) += kirkwood_nand.o
+obj-$(CONFIG_NAND_KMETER1) += kmeter1_nand.o
+obj-$(CONFIG_NAND_LPC32XX_MLC) += lpc32xx_nand_mlc.o
+obj-$(CONFIG_NAND_LPC32XX_SLC) += lpc32xx_nand_slc.o
+obj-$(CONFIG_NAND_VF610_NFC) += vf610_nfc.o
+obj-$(CONFIG_NAND_MXC) += mxc_nand.o
+obj-$(CONFIG_NAND_MXS) += mxs_nand.o
+obj-$(CONFIG_NAND_MXS_DT) += mxs_nand_dt.o
+obj-$(CONFIG_NAND_PXA3XX) += pxa3xx_nand.o
+obj-$(CONFIG_NAND_SPEAR) += spr_nand.o
+obj-$(CONFIG_TEGRA_NAND) += tegra_nand.o
+obj-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o
+obj-$(CONFIG_NAND_OMAP_ELM) += omap_elm.o
+obj-$(CONFIG_NAND_PLAT) += nand_plat.o
+obj-$(CONFIG_NAND_SUNXI) += sunxi_nand.o
+obj-$(CONFIG_NAND_ZYNQ) += zynq_nand.o
+
+else # minimal SPL drivers
+
+obj-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_spl.o
+obj-$(CONFIG_NAND_FSL_IFC) += fsl_ifc_spl.o
+obj-$(CONFIG_NAND_MXC) += mxc_nand_spl.o
+obj-$(CONFIG_NAND_MXS) += mxs_nand_spl.o mxs_nand.o
+obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o
+
+endif # drivers
diff --git a/drivers/mtd/nand/am335x_spl_bch.c b/drivers/mtd/nand/raw/am335x_spl_bch.c
similarity index 100%
rename from drivers/mtd/nand/am335x_spl_bch.c
rename to drivers/mtd/nand/raw/am335x_spl_bch.c
diff --git a/drivers/mtd/nand/arasan_nfc.c b/drivers/mtd/nand/raw/arasan_nfc.c
similarity index 100%
rename from drivers/mtd/nand/arasan_nfc.c
rename to drivers/mtd/nand/raw/arasan_nfc.c
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/raw/atmel_nand.c
similarity index 100%
rename from drivers/mtd/nand/atmel_nand.c
rename to drivers/mtd/nand/raw/atmel_nand.c
diff --git a/drivers/mtd/nand/atmel_nand_ecc.h b/drivers/mtd/nand/raw/atmel_nand_ecc.h
similarity index 100%
rename from drivers/mtd/nand/atmel_nand_ecc.h
rename to drivers/mtd/nand/raw/atmel_nand_ecc.h
diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/raw/davinci_nand.c
similarity index 99%
rename from drivers/mtd/nand/davinci_nand.c
rename to drivers/mtd/nand/raw/davinci_nand.c
index 305e68ad49..e6a84a52b4 100644
--- a/drivers/mtd/nand/davinci_nand.c
+++ b/drivers/mtd/nand/raw/davinci_nand.c
@@ -9,7 +9,7 @@
/*
*
- * linux/drivers/mtd/nand/nand_davinci.c
+ * linux/drivers/mtd/nand/raw/nand_davinci.c
*
* NAND Flash Driver
*
diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/raw/denali.c
similarity index 100%
rename from drivers/mtd/nand/denali.c
rename to drivers/mtd/nand/raw/denali.c
diff --git a/drivers/mtd/nand/denali.h b/drivers/mtd/nand/raw/denali.h
similarity index 100%
rename from drivers/mtd/nand/denali.h
rename to drivers/mtd/nand/raw/denali.h
diff --git a/drivers/mtd/nand/denali_dt.c b/drivers/mtd/nand/raw/denali_dt.c
similarity index 100%
rename from drivers/mtd/nand/denali_dt.c
rename to drivers/mtd/nand/raw/denali_dt.c
diff --git a/drivers/mtd/nand/denali_spl.c b/drivers/mtd/nand/raw/denali_spl.c
similarity index 100%
rename from drivers/mtd/nand/denali_spl.c
rename to drivers/mtd/nand/raw/denali_spl.c
diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/raw/fsl_elbc_nand.c
similarity index 100%
rename from drivers/mtd/nand/fsl_elbc_nand.c
rename to drivers/mtd/nand/raw/fsl_elbc_nand.c
diff --git a/drivers/mtd/nand/fsl_elbc_spl.c b/drivers/mtd/nand/raw/fsl_elbc_spl.c
similarity index 100%
rename from drivers/mtd/nand/fsl_elbc_spl.c
rename to drivers/mtd/nand/raw/fsl_elbc_spl.c
diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/raw/fsl_ifc_nand.c
similarity index 100%
rename from drivers/mtd/nand/fsl_ifc_nand.c
rename to drivers/mtd/nand/raw/fsl_ifc_nand.c
diff --git a/drivers/mtd/nand/fsl_ifc_spl.c b/drivers/mtd/nand/raw/fsl_ifc_spl.c
similarity index 100%
rename from drivers/mtd/nand/fsl_ifc_spl.c
rename to drivers/mtd/nand/raw/fsl_ifc_spl.c
diff --git a/drivers/mtd/nand/fsl_upm.c b/drivers/mtd/nand/raw/fsl_upm.c
similarity index 100%
rename from drivers/mtd/nand/fsl_upm.c
rename to drivers/mtd/nand/raw/fsl_upm.c
diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/raw/fsmc_nand.c
similarity index 100%
rename from drivers/mtd/nand/fsmc_nand.c
rename to drivers/mtd/nand/raw/fsmc_nand.c
diff --git a/drivers/mtd/nand/kb9202_nand.c b/drivers/mtd/nand/raw/kb9202_nand.c
similarity index 100%
rename from drivers/mtd/nand/kb9202_nand.c
rename to drivers/mtd/nand/raw/kb9202_nand.c
diff --git a/drivers/mtd/nand/kirkwood_nand.c b/drivers/mtd/nand/raw/kirkwood_nand.c
similarity index 100%
rename from drivers/mtd/nand/kirkwood_nand.c
rename to drivers/mtd/nand/raw/kirkwood_nand.c
diff --git a/drivers/mtd/nand/kmeter1_nand.c b/drivers/mtd/nand/raw/kmeter1_nand.c
similarity index 100%
rename from drivers/mtd/nand/kmeter1_nand.c
rename to drivers/mtd/nand/raw/kmeter1_nand.c
diff --git a/drivers/mtd/nand/lpc32xx_nand_mlc.c b/drivers/mtd/nand/raw/lpc32xx_nand_mlc.c
similarity index 100%
rename from drivers/mtd/nand/lpc32xx_nand_mlc.c
rename to drivers/mtd/nand/raw/lpc32xx_nand_mlc.c
diff --git a/drivers/mtd/nand/lpc32xx_nand_slc.c b/drivers/mtd/nand/raw/lpc32xx_nand_slc.c
similarity index 100%
rename from drivers/mtd/nand/lpc32xx_nand_slc.c
rename to drivers/mtd/nand/raw/lpc32xx_nand_slc.c
diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/raw/mxc_nand.c
similarity index 100%
rename from drivers/mtd/nand/mxc_nand.c
rename to drivers/mtd/nand/raw/mxc_nand.c
diff --git a/drivers/mtd/nand/mxc_nand.h b/drivers/mtd/nand/raw/mxc_nand.h
similarity index 100%
rename from drivers/mtd/nand/mxc_nand.h
rename to drivers/mtd/nand/raw/mxc_nand.h
diff --git a/drivers/mtd/nand/mxc_nand_spl.c b/drivers/mtd/nand/raw/mxc_nand_spl.c
similarity index 100%
rename from drivers/mtd/nand/mxc_nand_spl.c
rename to drivers/mtd/nand/raw/mxc_nand_spl.c
diff --git a/drivers/mtd/nand/mxs_nand.c b/drivers/mtd/nand/raw/mxs_nand.c
similarity index 100%
rename from drivers/mtd/nand/mxs_nand.c
rename to drivers/mtd/nand/raw/mxs_nand.c
diff --git a/drivers/mtd/nand/mxs_nand.h b/drivers/mtd/nand/raw/mxs_nand.h
similarity index 100%
rename from drivers/mtd/nand/mxs_nand.h
rename to drivers/mtd/nand/raw/mxs_nand.h
diff --git a/drivers/mtd/nand/mxs_nand_dt.c b/drivers/mtd/nand/raw/mxs_nand_dt.c
similarity index 100%
rename from drivers/mtd/nand/mxs_nand_dt.c
rename to drivers/mtd/nand/raw/mxs_nand_dt.c
diff --git a/drivers/mtd/nand/mxs_nand_spl.c b/drivers/mtd/nand/raw/mxs_nand_spl.c
similarity index 100%
rename from drivers/mtd/nand/mxs_nand_spl.c
rename to drivers/mtd/nand/raw/mxs_nand_spl.c
diff --git a/drivers/mtd/nand/nand.c b/drivers/mtd/nand/raw/nand.c
similarity index 100%
rename from drivers/mtd/nand/nand.c
rename to drivers/mtd/nand/raw/nand.c
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
similarity index 100%
rename from drivers/mtd/nand/nand_base.c
rename to drivers/mtd/nand/raw/nand_base.c
diff --git a/drivers/mtd/nand/nand_bbt.c b/drivers/mtd/nand/raw/nand_bbt.c
similarity index 100%
rename from drivers/mtd/nand/nand_bbt.c
rename to drivers/mtd/nand/raw/nand_bbt.c
diff --git a/drivers/mtd/nand/nand_bch.c b/drivers/mtd/nand/raw/nand_bch.c
similarity index 100%
rename from drivers/mtd/nand/nand_bch.c
rename to drivers/mtd/nand/raw/nand_bch.c
diff --git a/drivers/mtd/nand/nand_ecc.c b/drivers/mtd/nand/raw/nand_ecc.c
similarity index 99%
rename from drivers/mtd/nand/nand_ecc.c
rename to drivers/mtd/nand/raw/nand_ecc.c
index 05e55fce9a..2bc329be1a 100644
--- a/drivers/mtd/nand/nand_ecc.c
+++ b/drivers/mtd/nand/raw/nand_ecc.c
@@ -3,7 +3,7 @@
* This file contains an ECC algorithm from Toshiba that detects and
* corrects 1 bit errors in a 256 byte block of data.
*
- * drivers/mtd/nand/nand_ecc.c
+ * drivers/mtd/nand/raw/nand_ecc.c
*
* Copyright (C) 2000-2004 Steven J. Hill (sjhill at realitydiluted.com)
* Toshiba America Electronics Components, Inc.
diff --git a/drivers/mtd/nand/nand_ids.c b/drivers/mtd/nand/raw/nand_ids.c
similarity index 100%
rename from drivers/mtd/nand/nand_ids.c
rename to drivers/mtd/nand/raw/nand_ids.c
diff --git a/drivers/mtd/nand/nand_plat.c b/drivers/mtd/nand/raw/nand_plat.c
similarity index 100%
rename from drivers/mtd/nand/nand_plat.c
rename to drivers/mtd/nand/raw/nand_plat.c
diff --git a/drivers/mtd/nand/nand_spl_load.c b/drivers/mtd/nand/raw/nand_spl_load.c
similarity index 100%
rename from drivers/mtd/nand/nand_spl_load.c
rename to drivers/mtd/nand/raw/nand_spl_load.c
diff --git a/drivers/mtd/nand/nand_spl_loaders.c b/drivers/mtd/nand/raw/nand_spl_loaders.c
similarity index 100%
rename from drivers/mtd/nand/nand_spl_loaders.c
rename to drivers/mtd/nand/raw/nand_spl_loaders.c
diff --git a/drivers/mtd/nand/nand_spl_simple.c b/drivers/mtd/nand/raw/nand_spl_simple.c
similarity index 100%
rename from drivers/mtd/nand/nand_spl_simple.c
rename to drivers/mtd/nand/raw/nand_spl_simple.c
diff --git a/drivers/mtd/nand/nand_timings.c b/drivers/mtd/nand/raw/nand_timings.c
similarity index 100%
rename from drivers/mtd/nand/nand_timings.c
rename to drivers/mtd/nand/raw/nand_timings.c
diff --git a/drivers/mtd/nand/nand_util.c b/drivers/mtd/nand/raw/nand_util.c
similarity index 99%
rename from drivers/mtd/nand/nand_util.c
rename to drivers/mtd/nand/raw/nand_util.c
index 1ded7aa920..fc2235c1a0 100644
--- a/drivers/mtd/nand/nand_util.c
+++ b/drivers/mtd/nand/raw/nand_util.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0
/*
- * drivers/mtd/nand/nand_util.c
+ * drivers/mtd/nand/raw/nand_util.c
*
* Copyright (C) 2006 by Weiss-Electronic GmbH.
* All rights reserved.
diff --git a/drivers/mtd/nand/omap_elm.c b/drivers/mtd/nand/raw/omap_elm.c
similarity index 100%
rename from drivers/mtd/nand/omap_elm.c
rename to drivers/mtd/nand/raw/omap_elm.c
diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/raw/omap_gpmc.c
similarity index 100%
rename from drivers/mtd/nand/omap_gpmc.c
rename to drivers/mtd/nand/raw/omap_gpmc.c
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/raw/pxa3xx_nand.c
similarity index 99%
rename from drivers/mtd/nand/pxa3xx_nand.c
rename to drivers/mtd/nand/raw/pxa3xx_nand.c
index 9d02fd8eb1..67b2b62f76 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/raw/pxa3xx_nand.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0
/*
- * drivers/mtd/nand/pxa3xx_nand.c
+ * drivers/mtd/nand/raw/pxa3xx_nand.c
*
* Copyright © 2005 Intel Corporation
* Copyright © 2006 Marvell International Ltd.
diff --git a/drivers/mtd/nand/pxa3xx_nand.h b/drivers/mtd/nand/raw/pxa3xx_nand.h
similarity index 100%
rename from drivers/mtd/nand/pxa3xx_nand.h
rename to drivers/mtd/nand/raw/pxa3xx_nand.h
diff --git a/drivers/mtd/nand/sunxi_nand.c b/drivers/mtd/nand/raw/sunxi_nand.c
similarity index 100%
rename from drivers/mtd/nand/sunxi_nand.c
rename to drivers/mtd/nand/raw/sunxi_nand.c
diff --git a/drivers/mtd/nand/sunxi_nand_spl.c b/drivers/mtd/nand/raw/sunxi_nand_spl.c
similarity index 100%
rename from drivers/mtd/nand/sunxi_nand_spl.c
rename to drivers/mtd/nand/raw/sunxi_nand_spl.c
diff --git a/drivers/mtd/nand/tegra_nand.c b/drivers/mtd/nand/raw/tegra_nand.c
similarity index 100%
rename from drivers/mtd/nand/tegra_nand.c
rename to drivers/mtd/nand/raw/tegra_nand.c
diff --git a/drivers/mtd/nand/tegra_nand.h b/drivers/mtd/nand/raw/tegra_nand.h
similarity index 100%
rename from drivers/mtd/nand/tegra_nand.h
rename to drivers/mtd/nand/raw/tegra_nand.h
diff --git a/drivers/mtd/nand/vf610_nfc.c b/drivers/mtd/nand/raw/vf610_nfc.c
similarity index 100%
rename from drivers/mtd/nand/vf610_nfc.c
rename to drivers/mtd/nand/raw/vf610_nfc.c
diff --git a/drivers/mtd/nand/zynq_nand.c b/drivers/mtd/nand/raw/zynq_nand.c
similarity index 100%
rename from drivers/mtd/nand/zynq_nand.c
rename to drivers/mtd/nand/raw/zynq_nand.c
diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h
index 1f56deb151..2a58058ebb 100644
--- a/include/configs/MPC8313ERDB.h
+++ b/include/configs/MPC8313ERDB.h
@@ -242,7 +242,7 @@
/* LB refresh timer prescal, 266MHz/32 */
#define CONFIG_SYS_LBC_MRTPR 0x20000000 /*TODO */
-/* drivers/mtd/nand/nand.c */
+/* drivers/mtd/nand/raw/nand.c */
#if defined(CONFIG_NAND) && defined(CONFIG_SPL_BUILD)
#define CONFIG_SYS_NAND_BASE 0xFFF00000
#else
--
2.14.1
More information about the U-Boot
mailing list