[U-Boot] [PATCH] drivers: esdhc: add support for coldfire mcf5441x family

[Angelo Dureghello]

Signed-off-by: Angelo Dureghello <angelo at sysam.it>
---
 drivers/mmc/fsl_esdhc.c | 21 ++++++++++++++++-----
 include/fsl_esdhc.h     |  1 +
 2 files changed, 17 insertions(+), 5 deletions(-)

diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
index 4528345c67..e376926c53 100644
--- a/drivers/mmc/fsl_esdhc.c
+++ b/drivers/mmc/fsl_esdhc.c
@@ -26,6 +26,12 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#ifdef CONFIG_MCF5441x
+#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
+#define CONFIG_SYS_FSL_ESDHC_USE_PIO
+#endif
+#endif
+
 #define SDHCI_IRQ_EN_BITS		(IRQSTATEN_CC | IRQSTATEN_TC | \
 				IRQSTATEN_CINT | \
 				IRQSTATEN_CTOE | IRQSTATEN_CCE | IRQSTATEN_CEBE | \
@@ -399,7 +405,6 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc,
 	if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
 		return 0;
 #endif
-
 	esdhc_write32(&regs->irqstat, -1);
 
 	sync();
@@ -987,8 +992,12 @@ static int esdhc_init_common(struct fsl_esdhc_priv *priv, struct mmc *mmc)
 	/* Disable the BRR and BWR bits in IRQSTAT */
 	esdhc_clrbits32(&regs->irqstaten, IRQSTATEN_BRR | IRQSTATEN_BWR);
 
+#ifdef CONFIG_MCF5441x
+	esdhc_write32(&regs->proctl, PROCTL_INIT | PROCTL_D3CD);
+#else
 	/* Put the PROCTL reg back to the default */
 	esdhc_write32(&regs->proctl, PROCTL_INIT);
+#endif
 
 	/* Set timout to the maximum value */
 	esdhc_clrsetbits32(&regs->sysctl, SYSCTL_TIMEOUT_MASK, 14 << 16);
@@ -1014,7 +1023,6 @@ static int esdhc_getcd_common(struct fsl_esdhc_priv *priv)
 		return dm_gpio_get_value(&priv->cd_gpio);
 #endif
 #endif
-
 	while (!(esdhc_read32(&regs->prsstat) & PRSSTAT_CINS) && --timeout)
 		udelay(1000);
 
@@ -1112,11 +1120,16 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
 		esdhc_setbits32(&regs->vendorspec, ESDHC_VENDORSPEC_VSELECT);
 
 	writel(SDHCI_IRQ_EN_BITS, &regs->irqstaten);
+
+#ifdef CONFIG_MCF5441x
+	/* ColdFire, using SDHC_DATA[3] for card detection */
+	esdhc_write32(&regs->proctl, esdhc_read32(&regs->proctl) | PROCTL_D3CD);
+#endif
+
 	cfg = &plat->cfg;
 #ifndef CONFIG_DM_MMC
 	memset(cfg, '\0', sizeof(*cfg));
 #endif
-
 	voltage_caps = 0;
 	caps = esdhc_read32(&regs->hostcapblt);
 
@@ -1129,7 +1142,6 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
 #ifdef CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 	caps = caps | ESDHC_HOSTCAPBLT_VS33;
 #endif
-
 	if (caps & ESDHC_HOSTCAPBLT_VS18)
 		voltage_caps |= MMC_VDD_165_195;
 	if (caps & ESDHC_HOSTCAPBLT_VS30)
@@ -1150,7 +1162,6 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
 		printf("voltage not supported by controller\n");
 		return -1;
 	}
-
 	if (priv->bus_width == 8)
 		cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT;
 	else if (priv->bus_width == 4)
diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h
index acd8dd06f8..8dbd5249a7 100644
--- a/include/fsl_esdhc.h
+++ b/include/fsl_esdhc.h
@@ -106,6 +106,7 @@
 #define PROCTL_INIT		0x00000020
 #define PROCTL_DTW_4		0x00000002
 #define PROCTL_DTW_8		0x00000004
+#define PROCTL_D3CD		0x00000008
 
 #define CMDARG			0x0002e008
 
-- 
2.18.0