[U-Boot] [PATCH v4] spi: Add SPI driver for MT76xx SoCs

Stefan Roese sr at denx.de
Wed Aug 15 15:19:11 UTC 2018


This patch adds the SPI driver for the MediaTek MT7688 SoC (and
derivates). Its been tested on the LinkIt Smart 7688 and the Gardena
Smart Gateway with and SPI NOR on CS0 and on the Gardena Smart
Gateway additionally with an SPI NAND on CS1.

Note that the SPI controller only supports a max transfer size of 32
bytes. This driver implementes a workaround to enable bigger xfer
sizes to speed up the transfer especially for the SPI NAND support.

Signed-off-by: Stefan Roese <sr at denx.de>
Cc: Jagan Teki <jagan at openedev.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck at gmail.com>
Reviewed-by: Jagan Teki <jagan at openedev.com>
---
v4:
- Rename functions and macros from mt7621 to mt76xx to better
  reflect the SoC usage and match the driver name

v3:
- Drop IO wrappers completely as suggested by Daniel
- Read "clock-frequency" DT property instead of using 
  CONFIG_SYS_MIPS_TIMER_FREQ

v2:
- Add some macros instead of hardcoded numbers
- Move compatible DT struct down in the file 

 drivers/spi/Kconfig      |   8 +
 drivers/spi/Makefile     |   1 +
 drivers/spi/mt76xx_spi.c | 312 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 321 insertions(+)
 create mode 100644 drivers/spi/mt76xx_spi.c

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 9fbd26740d..6c4e50d3e9 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -116,6 +116,14 @@ config ICH_SPI
 	  access the SPI NOR flash on platforms embedding this Intel
 	  ICH IP core.
 
+config MT76XX_SPI
+	bool "MediaTek MT76XX SPI driver"
+	depends on ARCH_MT7620
+	help
+	  Enable the MT76XX SPI driver. This driver can be used to access
+	  the SPI NOR flash on platforms embedding these MediaTek
+	  SPI cores.
+
 config MVEBU_A3700_SPI
 	bool "Marvell Armada 3700 SPI driver"
 	select CLK_ARMADA_3720
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index bdb5b5a02f..3d13ba1b21 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -33,6 +33,7 @@ obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o
 obj-$(CONFIG_LPC32XX_SSP) += lpc32xx_ssp.o
 obj-$(CONFIG_MPC8XX_SPI) += mpc8xx_spi.o
 obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
+obj-$(CONFIG_MT76XX_SPI) += mt76xx_spi.o
 obj-$(CONFIG_MVEBU_A3700_SPI) += mvebu_a3700_spi.o
 obj-$(CONFIG_MXC_SPI) += mxc_spi.o
 obj-$(CONFIG_MXS_SPI) += mxs_spi.o
diff --git a/drivers/spi/mt76xx_spi.c b/drivers/spi/mt76xx_spi.c
new file mode 100644
index 0000000000..71ded3fe71
--- /dev/null
+++ b/drivers/spi/mt76xx_spi.c
@@ -0,0 +1,312 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Stefan Roese <sr at denx.de>
+ *
+ * Derived from the Linux driver version drivers/spi/spi-mt7621.c
+ *   Copyright (C) 2011 Sergiy <piratfm at gmail.com>
+ *   Copyright (C) 2011-2013 Gabor Juhos <juhosg at openwrt.org>
+ *   Copyright (C) 2014-2015 Felix Fietkau <nbd at nbd.name>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <spi.h>
+#include <wait_bit.h>
+#include <linux/io.h>
+
+#define SPI_MSG_SIZE_MAX	32	/* SPI message chunk size */
+/* Enough for SPI NAND page read / write with page size 2048 bytes */
+#define SPI_MSG_SIZE_OVERALL	(2048 + 16)
+
+#define MT76XX_SPI_TRANS	0x00
+#define MT76XX_SPI_TRANS_START	BIT(8)
+#define MT76XX_SPI_TRANS_BUSY	BIT(16)
+
+#define MT76XX_SPI_OPCODE	0x04
+#define MT76XX_SPI_DATA0	0x08
+#define MT76XX_SPI_DATA4	0x18
+#define MT76XX_SPI_MASTER	0x28
+#define MT76XX_SPI_MOREBUF	0x2c
+#define MT76XX_SPI_POLAR	0x38
+
+#define MT76XX_LSB_FIRST	BIT(3)
+#define MT76XX_CPOL		BIT(4)
+#define MT76XX_CPHA		BIT(5)
+
+#define MASTER_MORE_BUFMODE	BIT(2)
+#define MASTER_RS_CLK_SEL	GENMASK(27, 16)
+#define MASTER_RS_CLK_SEL_SHIFT	16
+#define MASTER_RS_SLAVE_SEL	GENMASK(31, 29)
+
+struct mt76xx_spi {
+	void __iomem *base;
+	unsigned int sys_freq;
+	u32 data[(SPI_MSG_SIZE_OVERALL / 4) + 1];
+	int tx_len;
+};
+
+static void mt76xx_spi_reset(struct mt76xx_spi *rs, int duplex)
+{
+	setbits_le32(rs->base + MT76XX_SPI_MASTER,
+		     MASTER_RS_SLAVE_SEL | MASTER_MORE_BUFMODE);
+}
+
+static void mt76xx_spi_set_cs(struct mt76xx_spi *rs, int cs, int enable)
+{
+	u32 val = 0;
+
+	debug("%s: cs#%d -> %s\n", __func__, cs, enable ? "enable" : "disable");
+	if (enable)
+		val = BIT(cs);
+	iowrite32(val, rs->base + MT76XX_SPI_POLAR);
+}
+
+static int mt76xx_spi_set_mode(struct udevice *bus, uint mode)
+{
+	struct mt76xx_spi *rs = dev_get_priv(bus);
+	u32 reg;
+
+	debug("%s: mode=0x%08x\n", __func__, mode);
+	reg = ioread32(rs->base + MT76XX_SPI_MASTER);
+
+	reg &= ~MT76XX_LSB_FIRST;
+	if (mode & SPI_LSB_FIRST)
+		reg |= MT76XX_LSB_FIRST;
+
+	reg &= ~(MT76XX_CPHA | MT76XX_CPOL);
+	switch (mode & (SPI_CPOL | SPI_CPHA)) {
+	case SPI_MODE_0:
+		break;
+	case SPI_MODE_1:
+		reg |= MT76XX_CPHA;
+		break;
+	case SPI_MODE_2:
+		reg |= MT76XX_CPOL;
+		break;
+	case SPI_MODE_3:
+		reg |= MT76XX_CPOL | MT76XX_CPHA;
+		break;
+	}
+	iowrite32(reg, rs->base + MT76XX_SPI_MASTER);
+
+	return 0;
+}
+
+static int mt76xx_spi_set_speed(struct udevice *bus, uint speed)
+{
+	struct mt76xx_spi *rs = dev_get_priv(bus);
+	u32 rate;
+	u32 reg;
+
+	debug("%s: speed=%d\n", __func__, speed);
+	rate = DIV_ROUND_UP(rs->sys_freq, speed);
+	debug("rate:%u\n", rate);
+
+	if (rate > 4097)
+		return -EINVAL;
+
+	if (rate < 2)
+		rate = 2;
+
+	reg = ioread32(rs->base + MT76XX_SPI_MASTER);
+	reg &= ~MASTER_RS_CLK_SEL;
+	reg |= (rate - 2) << MASTER_RS_CLK_SEL_SHIFT;
+	iowrite32(reg, rs->base + MT76XX_SPI_MASTER);
+
+	return 0;
+}
+
+static inline int mt76xx_spi_wait_till_ready(struct mt76xx_spi *rs)
+{
+	int ret;
+
+	ret =  wait_for_bit_le32(rs->base + MT76XX_SPI_TRANS,
+				 MT76XX_SPI_TRANS_BUSY, 0, 10, 0);
+	if (ret)
+		pr_err("Timeout in %s!\n", __func__);
+
+	return ret;
+}
+
+static int mt76xx_spi_xfer(struct udevice *dev, unsigned int bitlen,
+			   const void *dout, void *din, unsigned long flags)
+{
+	struct udevice *bus = dev->parent;
+	struct mt76xx_spi *rs = dev_get_priv(bus);
+	const u8 *tx_buf = dout;
+	u8 *ptr = (u8 *)dout;
+	u8 *rx_buf = din;
+	int total_size = bitlen >> 3;
+	int chunk_size;
+	int rx_len = 0;
+	u32 data[(SPI_MSG_SIZE_MAX / 4) + 1] = { 0 };
+	u32 val;
+	int i;
+
+	debug("%s: dout=%p, din=%p, len=%x, flags=%lx\n", __func__, dout, din,
+	      total_size, flags);
+
+	/*
+	 * This driver only supports half-duplex, so complain and bail out
+	 * upon full-duplex messages
+	 */
+	if (dout && din) {
+		printf("Only half-duplex SPI transfer supported\n");
+		return -EIO;
+	}
+
+	if (dout) {
+		debug("TX-DATA: ");
+		for (i = 0; i < total_size; i++)
+			debug("%02x ", *ptr++);
+		debug("\n");
+	}
+
+	mt76xx_spi_wait_till_ready(rs);
+
+	/*
+	 * Set CS active upon start of SPI message. This message can
+	 * be split upon multiple calls to this xfer function
+	 */
+	if (flags & SPI_XFER_BEGIN)
+		mt76xx_spi_set_cs(rs, spi_chip_select(dev), 1);
+
+	while (total_size > 0) {
+		/* Don't exceed the max xfer size */
+		chunk_size = min_t(int, total_size, SPI_MSG_SIZE_MAX);
+
+		/*
+		 * We might have some TX data buffered from the last xfer
+		 * message. Make sure, that this does not exceed the max
+		 * xfer size
+		 */
+		if (rs->tx_len > 4)
+			chunk_size -= rs->tx_len;
+		if (din)
+			rx_len = chunk_size;
+
+		if (tx_buf) {
+			/* Check if this message does not exceed the buffer */
+			if ((chunk_size + rs->tx_len) > SPI_MSG_SIZE_OVERALL) {
+				printf("TX message size too big (%d)\n",
+				       chunk_size + rs->tx_len);
+				return -EMSGSIZE;
+			}
+
+			/*
+			 * Write all TX data into internal buffer to collect
+			 * all TX messages into one buffer (might be split into
+			 * multiple calls to this function)
+			 */
+			for (i = 0; i < chunk_size; i++, rs->tx_len++) {
+				rs->data[rs->tx_len / 4] |=
+					tx_buf[i] << (8 * (rs->tx_len & 3));
+			}
+		}
+
+		if (flags & SPI_XFER_END) {
+			/* Write TX data into controller */
+			if (rs->tx_len) {
+				rs->data[0] = swab32(rs->data[0]);
+				if (rs->tx_len < 4)
+					rs->data[0] >>= (4 - rs->tx_len) * 8;
+
+				for (i = 0; i < rs->tx_len; i += 4) {
+					iowrite32(rs->data[i / 4], rs->base +
+						  MT76XX_SPI_OPCODE + i);
+				}
+			}
+
+			/* Write length into controller */
+			val = (min_t(int, rs->tx_len, 4) * 8) << 24;
+			if (rs->tx_len > 4)
+				val |= (rs->tx_len - 4) * 8;
+			val |= (rx_len * 8) << 12;
+			iowrite32(val, rs->base + MT76XX_SPI_MOREBUF);
+
+			/* Start the xfer */
+			setbits_le32(rs->base + MT76XX_SPI_TRANS,
+				     MT76XX_SPI_TRANS_START);
+
+			/* Wait until xfer is finished on bus */
+			mt76xx_spi_wait_till_ready(rs);
+
+			/* Reset TX length and TX buffer for next xfer */
+			rs->tx_len = 0;
+			memset(rs->data, 0, sizeof(rs->data));
+		}
+
+		for (i = 0; i < rx_len; i += 4)
+			data[i / 4] = ioread32(rs->base + MT76XX_SPI_DATA0 + i);
+
+		if (rx_len) {
+			debug("RX-DATA: ");
+			for (i = 0; i < rx_len; i++) {
+				rx_buf[i] = data[i / 4] >> (8 * (i & 3));
+				debug("%02x ", rx_buf[i]);
+			}
+			debug("\n");
+		}
+
+		if (tx_buf)
+			tx_buf += chunk_size;
+		if (rx_buf)
+			rx_buf += chunk_size;
+		total_size -= chunk_size;
+	}
+
+	/* Wait until xfer is finished on bus and de-assert CS */
+	mt76xx_spi_wait_till_ready(rs);
+	if (flags & SPI_XFER_END)
+		mt76xx_spi_set_cs(rs, spi_chip_select(dev), 0);
+
+	return 0;
+}
+
+static int mt76xx_spi_probe(struct udevice *dev)
+{
+	struct mt76xx_spi *rs = dev_get_priv(dev);
+
+	rs->base = dev_remap_addr(dev);
+	if (!rs->base)
+		return -EINVAL;
+
+	/*
+	 * Read input clock via DT for now. At some point this should be
+	 * replaced by implementing a clock driver for this SoC and getting
+	 * the SPI frequency via this clock driver.
+	 */
+	rs->sys_freq = dev_read_u32_default(dev, "clock-frequency", 0);
+	if (!rs->sys_freq) {
+		printf("Please provide clock-frequency!\n");
+		return -EINVAL;
+	}
+
+	mt76xx_spi_reset(rs, 0);
+
+	return 0;
+}
+
+static const struct dm_spi_ops mt76xx_spi_ops = {
+	.set_mode = mt76xx_spi_set_mode,
+	.set_speed = mt76xx_spi_set_speed,
+	.xfer = mt76xx_spi_xfer,
+	/*
+	 * cs_info is not needed, since we require all chip selects to be
+	 * in the device tree explicitly
+	 */
+};
+
+static const struct udevice_id mt76xx_spi_ids[] = {
+	{ .compatible = "ralink,mt76xx-spi" },
+	{ }
+};
+
+U_BOOT_DRIVER(mt76xx_spi) = {
+	.name = "mt76xx_spi",
+	.id = UCLASS_SPI,
+	.of_match = mt76xx_spi_ids,
+	.ops = &mt76xx_spi_ops,
+	.priv_auto_alloc_size = sizeof(struct mt76xx_spi),
+	.probe = mt76xx_spi_probe,
+};
-- 
2.18.0



More information about the U-Boot mailing list