[U-Boot] [PATCH v4 2/3] net: phy: ti: Recover from "port mirroring" N/A MODE4

[Janine Hagemann]

The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.

To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).

To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.

Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"

https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954

Based on commit ac6e058b75be ("net: phy: dp83867: Recover from "port mirroring"
N/A MODE4") of mainline linux kernel.

Signed-off-by: Janine Hagemann <j.hagemann at phytec.de>
Acked-by: Joe Hershberger <joe.hershberger at ni.com>
Acked-by: Lukasz Majewski <lukma at denx.de>
---
 drivers/net/phy/ti.c | 26 +++++++++++++++++++++++++-
 1 file changed, 25 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/ti.c b/drivers/net/phy/ti.c
index b5fa687..120867e 100644
--- a/drivers/net/phy/ti.c
+++ b/drivers/net/phy/ti.c
@@ -24,6 +24,7 @@
 /* Extended Registers */
 #define DP83867_CFG4		0x0031
 #define DP83867_RGMIICTL	0x0032
+#define DP83867_STRAP_STS1	0x006E
 #define DP83867_RGMIIDCTL	0x0086
 #define DP83867_IO_MUX_CFG	0x0170
 
@@ -48,8 +49,12 @@
 #define DP83867_RGMII_TX_CLK_DELAY_EN		BIT(1)
 #define DP83867_RGMII_RX_CLK_DELAY_EN		BIT(0)
 
+/* STRAP_STS1 bits */
+#define DP83867_STRAP_STS1_RESERVED		BIT(11)
+
 /* PHY CTRL bits */
 #define DP83867_PHYCR_FIFO_DEPTH_SHIFT		14
+#define DP83867_PHYCR_RESERVED_MASK	BIT(11)
 #define DP83867_MDI_CROSSOVER		5
 #define DP83867_MDI_CROSSOVER_AUTO	2
 #define DP83867_MDI_CROSSOVER_MDIX	2
@@ -254,7 +259,7 @@ static int dp83867_config(struct phy_device *phydev)
 {
 	struct dp83867_private *dp83867;
 	unsigned int val, delay, cfg2;
-	int ret;
+	int ret, bs;
 
 	if (!phydev->priv) {
 		dp83867 = kzalloc(sizeof(*dp83867), GFP_KERNEL);
@@ -289,6 +294,25 @@ static int dp83867_config(struct phy_device *phydev)
 			(dp83867->fifo_depth << DP83867_PHYCR_FIFO_DEPTH_SHIFT));
 		if (ret)
 			goto err_out;
+
+		/* The code below checks if "port mirroring" N/A MODE4 has been
+		 * enabled during power on bootstrap.
+		 *
+		 * Such N/A mode enabled by mistake can put PHY IC in some
+		 * internal testing mode and disable RGMII transmission.
+		 *
+		 * In this particular case one needs to check STRAP_STS1
+		 * register's bit 11 (marked as RESERVED).
+		 */
+
+		bs = phy_read_mmd_indirect(phydev, DP83867_STRAP_STS1,
+						DP83867_DEVADDR, phydev->addr);
+		val = phy_read(phydev, MDIO_DEVAD_NONE, MII_DP83867_PHYCTRL);
+		if (bs & DP83867_STRAP_STS1_RESERVED) {
+			val &= ~DP83867_PHYCR_RESERVED_MASK;
+			phy_write(phydev, MDIO_DEVAD_NONE, MII_DP83867_PHYCTRL, val);
+		}
+
 	} else if (phy_interface_is_sgmii(phydev)) {
 		phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR,
 			  (BMCR_ANENABLE | BMCR_FULLDPLX | BMCR_SPEED1000));
-- 
2.7.4