[U-Boot] [PATCH v2 4/7] ARM: mach-omap2: Kconfig: Allow OMAP5 devices to set entry point

[Andrew F. Davis]

Like AM33xx and AM43xx, DRA7xx and AM57xx devices may need to
have an non-standard boot address in memory. This may be due
to the device being a high security variant, which place the
Initial SoftWare (ISW) after certificates and secure software.

Allow these devices to set this from Kconfig.

Signed-off-by: Andrew F. Davis <afd at ti.com>
---
 arch/arm/mach-omap2/Kconfig        | 13 +++++++++++++
 arch/arm/mach-omap2/am33xx/Kconfig | 15 ---------------
 include/configs/ti_omap5_common.h  |  2 +-
 3 files changed, 14 insertions(+), 16 deletions(-)

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 58e545a45b..ebe3c0f39a 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -167,6 +167,19 @@ config TI_SECURE_EMIF_PROTECTED_REGION_SIZE
 	  using hardware memory firewalls. This value must be smaller than the
 	  TI_SECURE_EMIF_TOTAL_REGION_SIZE value.
 
+config ISW_ENTRY_ADDR
+	hex "Address in memory or XIP address of bootloader entry point"
+	default 0x402F4000 if AM43XX
+	default 0x402F0400 if AM33XX
+	default 0x40301350 if OMAP54XX
+	help
+	  After any reset, the boot ROM searches the boot media for a valid
+	  boot image. For non-XIP devices, the ROM then copies the image into
+	  internal memory. For all boot modes, after the ROM processes the
+	  boot image it eventually computes the entry point address depending
+	  on the device type (secure/non-secure), boot media (xip/non-xip) and
+	  image headers.
+
 source "arch/arm/mach-omap2/omap3/Kconfig"
 
 source "arch/arm/mach-omap2/omap4/Kconfig"
diff --git a/arch/arm/mach-omap2/am33xx/Kconfig b/arch/arm/mach-omap2/am33xx/Kconfig
index 3529607479..5f2ee83c27 100644
--- a/arch/arm/mach-omap2/am33xx/Kconfig
+++ b/arch/arm/mach-omap2/am33xx/Kconfig
@@ -274,21 +274,6 @@ config SPL_RTC_DDR_SUPPORT
 endif
 
 if AM43XX || AM33XX
-config ISW_ENTRY_ADDR
-	hex "Address in memory or XIP flash of bootloader entry point"
-	default 0x402F4000 if AM43XX
-	default 0x402F0400 if AM33XX
-	help
-	  After any reset, the boot ROM on the AM43XX SOC
-	  searches the boot media for a valid boot image.
-	  For non-XIP devices, the ROM then copies the
-	  image into internal memory.
-	  For all boot modes, after the ROM processes the
-	  boot image it eventually computes the entry
-	  point address depending on the device type
-	  (secure/non-secure), boot media (xip/non-xip) and
-	  image headers.
-
 config PUB_ROM_DATA_SIZE
 	hex "Size in bytes of the L3 SRAM reserved by ROM to store data"
 	default 0x8400
diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h
index 8bf4a6b7e9..ba57c40182 100644
--- a/include/configs/ti_omap5_common.h
+++ b/include/configs/ti_omap5_common.h
@@ -81,7 +81,7 @@
  * RAM from address 0x40301350 (0x40300000+0x1000(reserved)+0x350(cert)).
  */
 #define TI_OMAP5_SECURE_BOOT_RESV_SRAM_SZ	0x1000
-#define CONFIG_SPL_TEXT_BASE	0x40301350
+#define CONFIG_SPL_TEXT_BASE	CONFIG_ISW_ENTRY_ADDR
 /* If no specific start address is specified then the secure EMIF
  * region will be placed at the end of the DDR space. In order to prevent
  * the main u-boot relocation from clobbering that memory and causing a
-- 
2.19.1