[U-Boot] [PATCH 1/7] spi: update management of default speed and mode

Simon Goldschmidt simon.k.r.goldschmidt at gmail.com
Mon Dec 10 11:24:59 UTC 2018


On Mon, Dec 10, 2018 at 11:53 AM Patrick Delaunay
<patrick.delaunay at st.com> wrote:
>
> The 2 default values for SPI mode and speed are
> only if CONFIG_DM_SPI_FLASH is not defined
> - CONFIG_SF_DEFAULT_SPEED
> - CONFIG_SF_DEFAULT_MODE
>
> Inverse the logic of the test to remove these two defines.
>
> Signed-off-by: Patrick Delaunay <patrick.delaunay at st.com>
> ---
>
>  cmd/sf.c               | 10 ++++++----
>  common/spl/spl_spi.c   | 11 ++++++-----
>  common/splash_source.c | 11 ++++++-----
>  3 files changed, 18 insertions(+), 14 deletions(-)
>
> diff --git a/cmd/sf.c b/cmd/sf.c
> index 84bb057..cfea545 100644
> --- a/cmd/sf.c
> +++ b/cmd/sf.c
> @@ -81,16 +81,18 @@ static int do_spi_flash_probe(int argc, char * const argv[])
>  {
>         unsigned int bus = CONFIG_SF_DEFAULT_BUS;
>         unsigned int cs = CONFIG_SF_DEFAULT_CS;
> -       unsigned int speed = CONFIG_SF_DEFAULT_SPEED;
> -       unsigned int mode = CONFIG_SF_DEFAULT_MODE;
> +       /* In DM mode, defaults will be taken from DT */
> +       unsigned int speed = 0;
> +       unsigned int mode = 0;
>         char *endp;
>  #ifdef CONFIG_DM_SPI_FLASH
>         struct udevice *new, *bus_dev;
>         int ret;
> -       /* In DM mode defaults will be taken from DT */
> -       speed = 0, mode = 0;
>  #else
>         struct spi_flash *new;
> +
> +       speed = CONFIG_SF_DEFAULT_SPEED;
> +       mode = CONFIG_SF_DEFAULT_MODE;
>  #endif
>
>         if (argc >= 2) {
> diff --git a/common/spl/spl_spi.c b/common/spl/spl_spi.c
> index b348b45..c1c1fcb 100644
> --- a/common/spl/spl_spi.c
> +++ b/common/spl/spl_spi.c
> @@ -74,12 +74,13 @@ static int spl_spi_load_image(struct spl_image_info *spl_image,
>         unsigned payload_offs = CONFIG_SYS_SPI_U_BOOT_OFFS;
>         struct spi_flash *flash;
>         struct image_header *header;
> -       unsigned int max_hz = CONFIG_SF_DEFAULT_SPEED;
> -       unsigned int spi_mode = CONFIG_SF_DEFAULT_MODE;
> +       /* In DM mode, defaults will be taken from DT */
> +       unsigned int max_hz = 0;
> +       unsigned int spi_mode = 0;
>
> -#ifdef CONFIG_DM_SPI_FLASH
> -       /* In DM mode defaults will be taken from DT */
> -       max_hz = 0, spi_mode = 0;
> +#ifndef CONFIG_DM_SPI_FLASH
> +       max_hz = CONFIG_SF_DEFAULT_SPEED;
> +       spi_mode = CONFIG_SF_DEFAULT_MODE;
>  #endif
>         /*
>          * Load U-Boot image from SPI flash into RAM
> diff --git a/common/splash_source.c b/common/splash_source.c
> index 427196c..d5d5550 100644
> --- a/common/splash_source.c
> +++ b/common/splash_source.c
> @@ -24,12 +24,13 @@ DECLARE_GLOBAL_DATA_PTR;
>  static struct spi_flash *sf;
>  static int splash_sf_read_raw(u32 bmp_load_addr, int offset, size_t read_size)
>  {
> -       unsigned int max_hz = CONFIG_SF_DEFAULT_SPEED;
> -       unsigned int spi_mode = CONFIG_SF_DEFAULT_MODE;
> +       /* In DM mode, defaults will be taken from DT */
> +       unsigned int max_hz = 0;
> +       unsigned int spi_mode = 0;
>
> -#ifdef CONFIG_DM_SPI_FLASH
> -       /* In DM mode defaults will be taken from DT */
> -       max_hz = 0, spi_mode = 0;
> +#ifndef CONFIG_DM_SPI_FLASH
> +       max_hz = CONFIG_SF_DEFAULT_SPEED;
> +       spi_mode = CONFIG_SF_DEFAULT_MODE;
>  #endif
>
>         if (!sf) {

Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt at gmail.com>

Regards,
Simon


More information about the U-Boot mailing list