[U-Boot] [RESEND PATCH v3 3/3] imx: Add PHYTEC phyBOARD-i.MX6UL-Segin
Martyn Welch
martyn.welch at collabora.com
Mon Dec 10 12:18:37 UTC 2018
On Mon, 2018-12-10 at 12:49 +0100, Lukasz Majewski wrote:
> Hi Martyn,
>
> > Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer.
> > Based on the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
> >
> > CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
> > CPU: Industrial temperature grade (-40C to 105C) at 44C
> > Reset cause: POR
> > Board: PHYTEC phyCORE-i.MX6UL
> > I2C: ready
> > DRAM: 256 MiB
> > NAND: 512 MiB
> > MMC: FSL_SDHC: 0
> > In: serial
> > Out: serial
> > Err: serial
> > Net: FEC0
> >
> > Working:
> > - Eth0
> > - i2C
>
> I've noticed that you are using non DM I2C driver for IMX6Q. Was
> there
> any reason not to use it?
>
I didn't think I was, though now that you mention it I can see I've
left the defines in the board header. I'll remove them.
Martyn
> > - MMC/SD
> > - NAND
> > - UART (1 & 5)
> > - USB (host & otg)
> >
> > Signed-off-by: Martyn Welch <martyn.welch at collabora.com>
> >
> > ---
> >
> > Changes in v3:
> > - Correct spelling of Phytec
> > - Remove unneeded license information
> > - Correct image name in documentation
> > - Correct whitespacing
> > - Enable SPL to boot from MMC
> > - Simplify defconfig, remove non-SPL build
> >
> > Changes in v2:
> > - Switch to driver model
> >
> > arch/arm/dts/Makefile | 3 +-
> > arch/arm/dts/imx6ul-pcl063.dtsi | 173 +++++++++++++++++++++
> > arch/arm/dts/imx6ul-phycore-segin.dts | 76 ++++++++++
> > arch/arm/mach-imx/mx6/Kconfig | 13 ++
> > board/phytec/pcl063/Kconfig | 12 ++
> > board/phytec/pcl063/MAINTAINERS | 8 +
> > board/phytec/pcl063/Makefile | 7 +
> > board/phytec/pcl063/README | 26 ++++
> > board/phytec/pcl063/pcl063.c | 206
> > ++++++++++++++++++++++++++ board/phytec/pcl063/spl.c |
> > 160 ++++++++++++++++++++
> > configs/phycore_pcl063_defconfig | 61
> > ++++++++ include/configs/pcl063.h | 100 +++++++++++++
> > 12 files changed, 844 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm/dts/imx6ul-pcl063.dtsi
> > create mode 100644 arch/arm/dts/imx6ul-phycore-segin.dts
> > create mode 100644 board/phytec/pcl063/Kconfig
> > create mode 100644 board/phytec/pcl063/MAINTAINERS
> > create mode 100644 board/phytec/pcl063/Makefile
> > create mode 100644 board/phytec/pcl063/README
> > create mode 100644 board/phytec/pcl063/pcl063.c
> > create mode 100644 board/phytec/pcl063/spl.c
> > create mode 100644 configs/phycore_pcl063_defconfig
> > create mode 100644 include/configs/pcl063.h
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > index 949ee472fc..68411623e5 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -453,7 +453,8 @@ dtb-$(CONFIG_MX6UL) += \
> > imx6ul-isiot-nand.dtb \
> > imx6ul-opos6uldev.dtb \
> > imx6ul-14x14-evk.dtb \
> > - imx6ul-9x9-evk.dtb
> > + imx6ul-9x9-evk.dtb \
> > + imx6ul-phycore-segin.dtb
> >
> > dtb-$(CONFIG_MX6ULL) += imx6ull-14x14-evk.dtb
> >
> > diff --git a/arch/arm/dts/imx6ul-pcl063.dtsi
> > b/arch/arm/dts/imx6ul-pcl063.dtsi new file mode 100644
> > index 0000000000..24a6a47983
> > --- /dev/null
> > +++ b/arch/arm/dts/imx6ul-pcl063.dtsi
> > @@ -0,0 +1,173 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright (C) 2018 Collabora Ltd.
> > + *
> > + * Based on dts[i] from Phytec barebox port:
> > + * Copyright (C) 2016 PHYTEC Messtechnik GmbH
> > + * Author: Christian Hemp <c.hemp at phytec.de>
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "imx6ul.dtsi"
> > +
> > +/ {
> > + model = "Phytec phyCORE-i.MX6 Ultra Lite SOM";
> > + compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul";
> > +
> > + memory {
> > + reg = <0x80000000 0x20000000>;
> > + };
> > +
> > + chosen {
> > + stdout-path = &uart1;
> > + };
> > +};
> > +
> > +&fec1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet1>;
> > + phy-mode = "rmii";
> > + phy-handle = <ðphy0>;
> > + status = "okay";
> > +
> > + mdio: mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + ethphy0: ethernet-phy at 1 {
> > + reg = <1>;
> > + micrel,led-mode = <1>;
> > + };
> > + };
> > +};
> > +
> > +&gpmi {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_gpmi_nand>;
> > + nand-on-flash-bbt;
> > + fsl,no-blockmark-swap;
> > + status = "okay";
> > +
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + partition at 0 {
> > + label = "uboot";
> > + reg = <0x0 0x400000>;
> > + };
> > +
> > + partition at 400000 {
> > + label = "uboot-env";
> > + reg = <0x400000 0x100000>;
> > + };
> > +
> > + partition at 500000 {
> > + label = "root";
> > + reg = <0x500000 0x0>;
> > + };
> > +};
> > +
> > +&i2c1 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default", "gpio";
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + pinctrl-1 = <&pinctrl_i2c1_gpio>;
> > + scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
> > + sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
> > + status = "okay";
> > +
> > + eeprom at 52 {
> > + compatible = "cat,24c32";
> > + reg = <0x52>;
> > + };
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
> > + status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
> > + bus-width = <0x4>;
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + no-1-8-v;
> > + status = "okay";
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > +
> > + pinctrl_enet1: enet1grp {
> > + fsl,pins = <
> > + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO
> > 0x1b0b0
> > +
> > MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0X1b0b0
> > + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN
> > 0x1b0b0
> > + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER
> > 0x1b0b0
> > +
> > MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
> > +
> > MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
> > + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN
> > 0x1b0b0
> > +
> > MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
> > +
> > MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
> > +
> > MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
> > + >;
> > + };
> > +
> > + pinctrl_gpmi_nand: gpminandgrp {
> > + fsl,pins = <
> > +
> > MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
> > +
> > MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
> > + MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B
> > 0x0b0b1
> > +
> > MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
> > + MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B
> > 0x0b0b1
> > + MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B
> > 0x0b0b1
> > + MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B
> > 0x0b0b1
> > + MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00
> > 0x0b0b1
> > + MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01
> > 0x0b0b1
> > + MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02
> > 0x0b0b1
> > + MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03
> > 0x0b0b1
> > + MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04
> > 0x0b0b1
> > + MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05
> > 0x0b0b1
> > + MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06
> > 0x0b0b1
> > + MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07
> > 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c1: i2cgrp {
> > + fsl,pins = <
> > + MX6UL_PAD_UART4_TX_DATA__I2C1_SCL
> > 0x4001b8b0
> > + MX6UL_PAD_UART4_RX_DATA__I2C1_SDA
> > 0x4001b8b0
> > + >;
> > + };
> > +
> > + pinctrl_i2c1_gpio: i2c1grp_gpio {
> > + fsl,pins = <
> > + MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
> > + MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
> > + >;
> > + };
> > +
> > + pinctrl_uart1: uart1grp {
> > + fsl,pins = <
> > + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX
> > 0x1b0b1
> > + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX
> > 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1: usdhc1grp {
> > + fsl,pins = <
> > + MX6UL_PAD_SD1_CMD__USDHC1_CMD
> > 0x17059
> > + MX6UL_PAD_SD1_CLK__USDHC1_CLK
> > 0x10059
> > + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0
> > 0x17059
> > + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1
> > 0x17059
> > + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2
> > 0x17059
> > + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3
> > 0x17059
> > + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19
> > 0x17059 +
> > + >;
> > + };
> > +};
> > diff --git a/arch/arm/dts/imx6ul-phycore-segin.dts
> > b/arch/arm/dts/imx6ul-phycore-segin.dts new file mode 100644
> > index 0000000000..a46012e2b4
> > --- /dev/null
> > +++ b/arch/arm/dts/imx6ul-phycore-segin.dts
> > @@ -0,0 +1,76 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright (C) 2018 Collabora Ltd.
> > + *
> > + * Based on dts[i] from Phytec barebox port:
> > + * Copyright (C) 2016 PHYTEC Messtechnik GmbH
> > + * Author: Christian Hemp <c.hemp at phytec.de>
> > + *
> > + * The code contained herein is licensed under the GNU General
> > Public
> > + * License. You may obtain a copy of the GNU General Public
> > License
> > + * Version 2 or later at the following locations:
> > + *
> > + * http://www.opensource.org/licenses/gpl-license.html
> > + * http://www.gnu.org/copyleft/gpl.html
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "imx6ul-pcl063.dtsi"
> > +
> > +/ {
> > + model = "Phytec phyBOARD-i.MX6UL-Segin SBC";
> > + compatible = "phytec,phyboard-imx6ul-segin",
> > "phytec,imx6ul-pcl063",
> > + "fsl,imx6ul";
> > +};
> > +
> > +&i2c1 {
> > + i2c_rtc: rtc at 68 {
> > + compatible = "microcrystal,rv4162";
> > + reg = <0x68>;
> > + status = "okay";
> > + };
> > +};
> > +
> > +&uart5 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart5>;
> > + uart-has-rtscts;
> > + status = "okay";
> > +};
> > +
> > +&usbotg1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usb_otg1_id>;
> > + dr_mode = "otg";
> > + srp-disable;
> > + hnp-disable;
> > + adp-disable;
> > + status = "okay";
> > +};
> > +
> > +&usbotg2 {
> > + dr_mode = "host";
> > + disable-over-current;
> > + status = "okay";
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > +
> > + pinctrl_uart5: uart5grp {
> > + fsl,pins = <
> > + MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX
> > 0x1b0b1
> > + MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX
> > 0x1b0b1
> > + MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS
> > 0x1b0b1
> > + MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS
> > 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usb_otg1_id: usbotg1idgrp {
> > + fsl,pins = <
> > + MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID
> > 0x17059
> > + >;
> > + };
> > +
> > +};
> > diff --git a/arch/arm/mach-imx/mx6/Kconfig
> > b/arch/arm/mach-imx/mx6/Kconfig index 06c25bae36..e253f495c5 100644
> > --- a/arch/arm/mach-imx/mx6/Kconfig
> > +++ b/arch/arm/mach-imx/mx6/Kconfig
> > @@ -428,6 +428,18 @@ config TARGET_PFLA02
> > select MX6QDL
> > select SUPPORT_SPL
> >
> > +config TARGET_PCL063
> > + bool "PHYTEC PCL063 (phyCORE-i.MX6UL)"
> > + select MX6UL
> > + select DM
> > + select DM_ETH
> > + select DM_GPIO
> > + select DM_I2C
> > + select DM_MMC
> > + select DM_SERIAL
> > + select DM_THERMAL
> > + select SUPPORT_SPL
> > +
> > config TARGET_SECOMX6
> > bool "secomx6 boards"
> >
> > @@ -550,6 +562,7 @@ source "board/freescale/mx6ullevk/Kconfig"
> > source "board/grinn/liteboard/Kconfig"
> > source "board/phytec/pcm058/Kconfig"
> > source "board/phytec/pfla02/Kconfig"
> > +source "board/phytec/pcl063/Kconfig"
> > source "board/gateworks/gw_ventana/Kconfig"
> > source "board/kosagi/novena/Kconfig"
> > source "board/samtec/vining_2000/Kconfig"
> > diff --git a/board/phytec/pcl063/Kconfig
> > b/board/phytec/pcl063/Kconfig
> > new file mode 100644
> > index 0000000000..977db70f64
> > --- /dev/null
> > +++ b/board/phytec/pcl063/Kconfig
> > @@ -0,0 +1,12 @@
> > +if TARGET_PCL063
> > +
> > +config SYS_BOARD
> > + default "pcl063"
> > +
> > +config SYS_VENDOR
> > + default "phytec"
> > +
> > +config SYS_CONFIG_NAME
> > + default "pcl063"
> > +
> > +endif
> > diff --git a/board/phytec/pcl063/MAINTAINERS
> > b/board/phytec/pcl063/MAINTAINERS new file mode 100644
> > index 0000000000..c65a951f3d
> > --- /dev/null
> > +++ b/board/phytec/pcl063/MAINTAINERS
> > @@ -0,0 +1,8 @@
> > +PCL063 BOARD
> > +M: Martyn Welch <martyn.welch at collabora.com>
> > +S: Maintained
> > +F: arch/arm/dts/imx6ul-pcl063.dtsi
> > +F: arch/arm/dts/imx6ul-phycore-segin.dts
> > +F: board/phytec/pcl063/
> > +F: configs/phycore_pcl063_defconfig
> > +F: include/configs/pcl063.h
> > diff --git a/board/phytec/pcl063/Makefile
> > b/board/phytec/pcl063/Makefile new file mode 100644
> > index 0000000000..53c73c9b08
> > --- /dev/null
> > +++ b/board/phytec/pcl063/Makefile
> > @@ -0,0 +1,7 @@
> > +# Copyright (C) 2018 Collabora Ltd.
> > +#
> > +# SPDX-License-Identifier: GPL-2.0+
> > +#
> > +
> > +obj-y := pcl063.o
> > +obj-$(CONFIG_SPL_BUILD) += spl.o
> > diff --git a/board/phytec/pcl063/README
> > b/board/phytec/pcl063/README
> > new file mode 100644
> > index 0000000000..be83bdb0d8
> > --- /dev/null
> > +++ b/board/phytec/pcl063/README
> > @@ -0,0 +1,26 @@
> > +How to use U-Boot on PHYTEC phyBOARD-i.MX6UL-Segin
> > +--------------------------------------------------
> > +
> > +- Configure and build U-Boot for phyCORE-i.MX6UL:
> > +
> > + $ make mrproper
> > + $ make phycore_pcl063_defconfig
> > + $ make
> > +
> > + This will generate SPL and u-boot-dtb.img images.
> > +
> > +- The SPL and u-boot-dtb.img images need to be flashed into the
> > micro SD card: +
> > + $ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
> > + $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69;
> > sync
> > +
> > +- Jumper settings:
> > +
> > + JP1: Open: Boot from NAND
> > + Closed: Boot from SD/MMC1
> > +
> > +- Connect the Serial cable to UART0 and the PC for the console.
> > +
> > +- Insert the micro SD card in the board and power it up.
> > +
> > +- U-Boot messages should come up.
> > diff --git a/board/phytec/pcl063/pcl063.c
> > b/board/phytec/pcl063/pcl063.c new file mode 100644
> > index 0000000000..38b233d1b0
> > --- /dev/null
> > +++ b/board/phytec/pcl063/pcl063.c
> > @@ -0,0 +1,206 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright (C) 2018 Collabora Ltd.
> > + *
> > + * Based on board/ccv/xpress/xpress.c:
> > + * Copyright (C) 2015-2016 Stefan Roese <sr at denx.de>
> > + */
> > +
> > +#include <asm/arch/clock.h>
> > +#include <asm/arch/crm_regs.h>
> > +#include <asm/arch/mx6-pins.h>
> > +#include <asm/arch/sys_proto.h>
> > +#include <asm/mach-imx/iomux-v3.h>
> > +#include <asm/mach-imx/mxc_i2c.h>
> > +#include <fsl_esdhc.h>
> > +#include <linux/bitops.h>
> > +#include <miiphy.h>
> > +#include <netdev.h>
> > +#include <usb.h>
> > +#include <usb/ehci-ci.h>
> > +
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +int dram_init(void)
> > +{
> > + gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
> > PHYS_SDRAM_SIZE); +
> > + return 0;
> > +}
> > +
> > +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |
> > \
> > + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
> > + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | \
> > + PAD_CTL_HYS)
> > +
> > +static iomux_v3_cfg_t const uart1_pads[] = {
> > + MX6_PAD_UART1_TX_DATA__UART1_DCE_TX |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > + MX6_PAD_UART1_RX_DATA__UART1_DCE_RX |
> > MUX_PAD_CTRL(UART_PAD_CTRL), +};
> > +
> > +static iomux_v3_cfg_t const uart5_pads[] = {
> > + MX6_PAD_UART5_TX_DATA__UART5_DCE_TX |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > + MX6_PAD_UART5_RX_DATA__UART5_DCE_RX |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > + MX6_PAD_GPIO1_IO09__UART5_DCE_CTS |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > + MX6_PAD_GPIO1_IO08__UART5_DCE_RTS |
> > MUX_PAD_CTRL(UART_PAD_CTRL), +};
> > +
> > +static void setup_iomux_uart(void)
> > +{
> > + imx_iomux_v3_setup_multiple_pads(uart1_pads,
> > ARRAY_SIZE(uart1_pads));
> > + imx_iomux_v3_setup_multiple_pads(uart5_pads,
> > ARRAY_SIZE(uart5_pads)); +}
> > +
> > +#ifdef CONFIG_NAND_MXS
> > +
> > +#define NAND_PAD_CTRL (PAD_CTL_DSE_48ohm | PAD_CTL_SRE_SLOW |
> > PAD_CTL_HYS) +
> > +#define NAND_PAD_READY0_CTRL (PAD_CTL_DSE_48ohm |
> > PAD_CTL_PUS_22K_UP)
> > +
> > +#define NANDREADYPC MUX_PAD_CTRL(NAND_PAD_READY0_CTRL)
> > +
> > +static iomux_v3_cfg_t const gpmi_pads[] = {
> > + MX6_PAD_NAND_DATA00__RAWNAND_DATA00 |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_DATA01__RAWNAND_DATA01 |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_DATA02__RAWNAND_DATA02 |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_DATA03__RAWNAND_DATA03 |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_DATA04__RAWNAND_DATA04 |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_DATA05__RAWNAND_DATA05 |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_DATA06__RAWNAND_DATA06 |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_DATA07__RAWNAND_DATA07 |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_CLE__RAWNAND_CLE |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_ALE__RAWNAND_ALE |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_RE_B__RAWNAND_RE_B |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_WE_B__RAWNAND_WE_B |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B |
> > MUX_PAD_CTRL(NAND_PAD_CTRL),
> > + MX6_PAD_NAND_READY_B__RAWNAND_READY_B | NANDREADYPC,
> > +};
> > +
> > +static void setup_gpmi_nand(void)
> > +{
> > + imx_iomux_v3_setup_multiple_pads(gpmi_pads,
> > ARRAY_SIZE(gpmi_pads)); +
> > + setup_gpmi_io_clk((3 << MXC_CCM_CSCDR1_BCH_PODF_OFFSET) |
> > + (3 << MXC_CCM_CSCDR1_GPMI_PODF_OFFSET));
> > +}
> > +
> > +#endif /* CONFIG_NAND_MXS */
> > +
> > +#ifdef CONFIG_FEC_MXC
> > +
> > +#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
> > +
> > +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP |
> > PAD_CTL_PUE |
> > \
> > + PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm |
> > \
> > + PAD_CTL_SRE_FAST)
> > +
> > +#define MDIO_PAD_CTRL (PAD_CTL_PUS_100K_UP |
> > PAD_CTL_PUE | \
> > + PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST | \
> > + PAD_CTL_ODE)
> > +
> > +static iomux_v3_cfg_t const fec1_pads[] = {
> > + MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
> > + MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_TX_EN__ENET1_TX_EN |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 |
> > MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
> > + MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_RX_ER__ENET1_RX_ER |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_RX_EN__ENET1_RX_EN |
> > MUX_PAD_CTRL(ENET_PAD_CTRL), +};
> > +
> > +static iomux_v3_cfg_t const fec2_pads[] = {
> > + MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET2_TX_EN__ENET2_TX_EN |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 |
> > MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
> > + MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET2_RX_ER__ENET2_RX_ER |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET2_RX_EN__ENET2_RX_EN |
> > MUX_PAD_CTRL(ENET_PAD_CTRL), +};
> > +
> > +static void setup_iomux_fec(void)
> > +{
> > + imx_iomux_v3_setup_multiple_pads(fec1_pads,
> > ARRAY_SIZE(fec1_pads));
> > + imx_iomux_v3_setup_multiple_pads(fec2_pads,
> > ARRAY_SIZE(fec2_pads)); +}
> > +
> > +static int setup_fec(void)
> > +{
> > + struct iomuxc *const iomuxc_regs = (struct iomuxc
> > *)IOMUXC_BASE_ADDR;
> > + int ret;
> > +
> > + /*
> > + * Use 50M anatop loopback REF_CLK1 for ENET1,
> > + * clear gpr1[13], set gpr1[17].
> > + */
> > + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
> > + IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
> > +
> > + ret = enable_fec_anatop_clock(0, ENET_50MHZ);
> > + if (ret)
> > + return ret;
> > +
> > + /*
> > + * Use 50M anatop loopback REF_CLK2 for ENET2,
> > + * clear gpr1[14], set gpr1[18].
> > + */
> > + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
> > + IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
> > +
> > + ret = enable_fec_anatop_clock(1, ENET_50MHZ);
> > + if (ret)
> > + return ret;
> > +
> > + enable_enet_clk(1);
> > +
> > + return 0;
> > +}
> > +
> > +int board_phy_config(struct phy_device *phydev)
> > +{
> > + /*
> > + * Defaults + Enable status LEDs (LED1: Activity, LED0:
> > Link) & select
> > + * 50 MHz RMII clock mode.
> > + */
> > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
> > +
> > + if (phydev->drv->config)
> > + phydev->drv->config(phydev);
> > +
> > + return 0;
> > +}
> > +#endif /* CONFIG_FEC_MXC */
> > +
> > +int board_early_init_f(void)
> > +{
> > + setup_iomux_uart();
> > + setup_iomux_fec();
> > +
> > + return 0;
> > +}
> > +
> > +int board_init(void)
> > +{
> > + /* Address of boot parameters */
> > + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
> > +
> > +#ifdef CONFIG_NAND_MXS
> > + setup_gpmi_nand();
> > +#endif
> > +
> > +#ifdef CONFIG_FEC_MXC
> > + setup_fec();
> > +#endif
> > + return 0;
> > +}
> > +
> > +int checkboard(void)
> > +{
> > + puts("Board: PHYTEC phyCORE-i.MX6UL\n");
> > +
> > + return 0;
> > +}
> > diff --git a/board/phytec/pcl063/spl.c b/board/phytec/pcl063/spl.c
> > new file mode 100644
> > index 0000000000..d071e16576
> > --- /dev/null
> > +++ b/board/phytec/pcl063/spl.c
> > @@ -0,0 +1,160 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright (C) 2018 Collabora Ltd.
> > + *
> > + * Based on board/ccv/xpress/spl.c:
> > + * Copyright (C) 2015-2016 Stefan Roese <sr at denx.de>
> > + */
> > +
> > +#include <common.h>
> > +#include <spl.h>
> > +#include <asm/arch/clock.h>
> > +#include <asm/io.h>
> > +#include <asm/arch/mx6-ddr.h>
> > +#include <asm/arch/mx6-pins.h>
> > +#include <asm/arch/crm_regs.h>
> > +#include <fsl_esdhc.h>
> > +
> > +/* Configuration for Micron MT41K256M16TW-107 IT:P, 32M x 16 x 8
> > ->
> > 256MiB */ +
> > +static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
> > + .grp_addds = 0x00000030,
> > + .grp_ddrmode_ctl = 0x00020000,
> > + .grp_b0ds = 0x00000030,
> > + .grp_ctlds = 0x00000030,
> > + .grp_b1ds = 0x00000030,
> > + .grp_ddrpke = 0x00000000,
> > + .grp_ddrmode = 0x00020000,
> > + .grp_ddr_type = 0x000c0000,
> > +};
> > +
> > +static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
> > + .dram_dqm0 = 0x00000030,
> > + .dram_dqm1 = 0x00000030,
> > + .dram_ras = 0x00000030,
> > + .dram_cas = 0x00000030,
> > + .dram_odt0 = 0x00000030,
> > + .dram_odt1 = 0x00000030,
> > + .dram_sdba2 = 0x00000000,
> > + .dram_sdclk_0 = 0x00000030,
> > + .dram_sdqs0 = 0x00000030,
> > + .dram_sdqs1 = 0x00000030,
> > + .dram_reset = 0x00000030,
> > +};
> > +
> > +static struct mx6_mmdc_calibration mx6_mmcd_calib = {
> > + .p0_mpwldectrl0 = 0x00000000,
> > + .p0_mpdgctrl0 = 0x41480148,
> > + .p0_mprddlctl = 0x40403E42,
> > + .p0_mpwrdlctl = 0x40405852,
> > +};
> > +
> > +struct mx6_ddr_sysinfo ddr_sysinfo = {
> > + .dsize = 0, /* Bus size = 16bit */
> > + .cs_density = 18,
> > + .ncs = 1,
> > + .cs1_mirror = 0,
> > + .rtt_wr = 1,
> > + .rtt_nom = 1,
> > + .walat = 1, /* Write additional latency */
> > + .ralat = 5, /* Read additional latency */
> > + .mif3_mode = 3, /* Command prediction working
> > mode */
> > + .bi_on = 1, /* Bank interleaving enabled */
> > + .pd_fast_exit = 1,
> > + .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC
> > default) */
> > + .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC
> > default) */
> > + .ddr_type = DDR_TYPE_DDR3,
> > + .refsel = 1, /* Refresh cycles at 32KHz */
> > + .refr = 7, /* 8 refresh commands per refresh
> > cycle */ +};
> > +
> > +static struct mx6_ddr3_cfg mem_ddr = {
> > + .mem_speed = 933,
> > + .density = 4,
> > + .width = 16,
> > + .banks = 8,
> > + .rowaddr = 14,
> > + .coladdr = 10,
> > + .pagesz = 1,
> > + .trcd = 1391,
> > + .trcmin = 4791,
> > + .trasmin = 3400,
> > +};
> > +
> > +static void ccgr_init(void)
> > +{
> > + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg
> > *)CCM_BASE_ADDR; +
> > + writel(0xFFFFFFFF, &ccm->CCGR0);
> > + writel(0xFFFFFFFF, &ccm->CCGR1);
> > + writel(0xFFFFFFFF, &ccm->CCGR2);
> > + writel(0xFFFFFFFF, &ccm->CCGR3);
> > + writel(0xFFFFFFFF, &ccm->CCGR4);
> > + writel(0xFFFFFFFF, &ccm->CCGR5);
> > + writel(0xFFFFFFFF, &ccm->CCGR6);
> > +}
> > +
> > +static void spl_dram_init(void)
> > +{
> > + mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs,
> > &mx6_grp_ioregs);
> > + mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
> > +}
> > +
> > +#ifdef CONFIG_FSL_ESDHC
> > +
> > +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |
> > \
> > + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
> > + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | \
> > + PAD_CTL_HYS)
> > +
> > +static iomux_v3_cfg_t const usdhc1_pads[] = {
> > + MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_SD1_DATA0__USDHC1_DATA0 |
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_SD1_DATA1__USDHC1_DATA1 |
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_SD1_DATA2__USDHC1_DATA2 |
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_SD1_DATA3__USDHC1_DATA3 |
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_UART1_RTS_B__USDHC1_CD_B |
> > MUX_PAD_CTRL(USDHC_PAD_CTRL), +};
> > +
> > +static struct fsl_esdhc_cfg usdhc_cfg[] = {
> > + {
> > + .esdhc_base = USDHC1_BASE_ADDR,
> > + .max_bus_width = 4,
> > + },
> > +};
> > +
> > +int board_mmc_getcd(struct mmc *mmc)
> > +{
> > + return 1;
> > +}
> > +
> > +int board_mmc_init(bd_t *bis)
> > +{
> > + imx_iomux_v3_setup_multiple_pads(usdhc1_pads,
> > ARRAY_SIZE(usdhc1_pads));
> > + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
> > +
> > + return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
> > +}
> > +
> > +#endif /* CONFIG_FSL_ESDHC */
> > +
> > +void board_init_f(ulong dummy)
> > +{
> > + ccgr_init();
> > +
> > + /* Setup AIPS and disable watchdog */
> > + arch_cpu_init();
> > +
> > + /* Setup iomux and i2c */
> > + board_early_init_f();
> > +
> > + /* Setup GP timer */
> > + timer_init();
> > +
> > + /* UART clocks enabled and gd valid - init serial console */
> > + preloader_console_init();
> > +
> > + /* DDR initialization */
> > + spl_dram_init();
> > +}
> > diff --git a/configs/phycore_pcl063_defconfig
> > b/configs/phycore_pcl063_defconfig new file mode 100644
> > index 0000000000..bc6ebe68c8
> > --- /dev/null
> > +++ b/configs/phycore_pcl063_defconfig
> > @@ -0,0 +1,61 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_MX6=y
> > +CONFIG_SYS_TEXT_BASE=0x87800000
> > +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> > +CONFIG_SPL_LIBGENERIC_SUPPORT=y
> > +CONFIG_TARGET_PCL063=y
> > +CONFIG_SPL_MMC_SUPPORT=y
> > +CONFIG_SPL_SERIAL_SUPPORT=y
> > +CONFIG_SPL=y
> > +CONFIG_DISTRO_DEFAULTS=y
> > +CONFIG_NR_DRAM_BANKS=8
> > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
> > +CONFIG_BOOTDELAY=3
> > +# CONFIG_USE_BOOTCOMMAND is not set
> > +CONFIG_BOARD_EARLY_INIT_F=y
> > +CONFIG_SPL_USB_HOST_SUPPORT=y
> > +CONFIG_SPL_USB_GADGET_SUPPORT=y
> > +CONFIG_SPL_USB_SDP_SUPPORT=y
> > +CONFIG_SPL_WATCHDOG_SUPPORT=y
> > +CONFIG_CMD_MEMTEST=y
> > +CONFIG_CMD_DM=y
> > +CONFIG_CMD_GPIO=y
> > +CONFIG_CMD_GPT=y
> > +# CONFIG_RANDOM_UUID is not set
> > +CONFIG_CMD_I2C=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_CMD_MTD=y
> > +CONFIG_CMD_USB=y
> > +CONFIG_CMD_USB_SDP=y
> > +CONFIG_CMD_CACHE=y
> > +CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
> > +CONFIG_MTDPARTS_DEFAULT="gpmi-nand:4m(uboot),1m(env),-(root)"
> > +CONFIG_CMD_UBI=y
> > +# CONFIG_ISO_PARTITION is not set
> > +CONFIG_OF_CONTROL=y
> > +CONFIG_DEFAULT_DEVICE_TREE="imx6ul-phycore-segin"
> > +CONFIG_DM_I2C_GPIO=y
> > +CONFIG_FSL_ESDHC=y
> > +CONFIG_MTD=y
> > +CONFIG_NAND=y
> > +CONFIG_NAND_MXS=y
> > +CONFIG_NAND_MXS_DT=y
> > +CONFIG_PHYLIB=y
> > +CONFIG_PHY_MICREL=y
> > +CONFIG_FEC_MXC=y
> > +CONFIG_MII=y
> > +CONFIG_PINCTRL=y
> > +CONFIG_PINCTRL_IMX6=y
> > +CONFIG_DM_PMIC=y
> > +# CONFIG_SPL_PMIC_CHILDREN is not set
> > +CONFIG_DM_REGULATOR=y
> > +CONFIG_DM_REGULATOR_FIXED=y
> > +CONFIG_MXC_UART=y
> > +CONFIG_USB=y
> > +CONFIG_DM_USB=y
> > +CONFIG_USB_GADGET=y
> > +CONFIG_USB_GADGET_MANUFACTURER="Phytec"
> > +CONFIG_USB_GADGET_VENDOR_NUM=0x01b67
> > +CONFIG_USB_GADGET_PRODUCT_NUM=0x4fff
> > +CONFIG_CI_UDC=y
> > +CONFIG_USB_GADGET_DOWNLOAD=y
> > diff --git a/include/configs/pcl063.h b/include/configs/pcl063.h
> > new file mode 100644
> > index 0000000000..d8856b3e5d
> > --- /dev/null
> > +++ b/include/configs/pcl063.h
> > @@ -0,0 +1,100 @@
> > +/* SPDX-License-Identifier: GPL-2.0+ */
> > +/*
> > + * Copyright (C) 2018 Collabora Ltd.
> > + *
> > + * Based on include/configs/xpress.h:
> > + * Copyright (C) 2015-2016 Stefan Roese <sr at denx.de>
> > + */
> > +#ifndef __PCL063_H
> > +#define __PCL063_H
> > +
> > +#include <linux/sizes.h>
> > +#include "mx6_common.h"
> > +
> > +/* SPL options */
> > +#include "imx6_spl.h"
> > +
> > +/*
> > + * There is a bug in some i.MX6UL processors that results in the
> > initial
> > + * portion of OCRAM being unavailable when booting from (at least)
> > an SD
> > + * card.
> > + *
> > + * Tweak the SPL text base address to avoid this.
> > + */
> > +#undef CONFIG_SPL_TEXT_BASE
> > +#define CONFIG_SPL_TEXT_BASE 0x00909000
> > +
> > +/* Size of malloc() pool */
> > +#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
> > +
> > +/* Console configs */
> > +#define CONFIG_MXC_UART_BASE UART1_BASE
> > +
> > +/* MMC Configs */
> > +#define CONFIG_FSL_USDHC
> > +
> > +#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC1_BASE_ADDR
> > +
> > +/* I2C configs */
> > +#ifdef CONFIG_CMD_I2C
> > +#define CONFIG_SYS_I2C_MXC
> > +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
> > +#define CONFIG_SYS_I2C_SPEED 100000
> > +#endif
> > +
> > +/* Miscellaneous configurable options */
> > +#define CONFIG_SYS_MEMTEST_START 0x80000000
> > +#define CONFIG_SYS_MEMTEST_END
> > (CONFIG_SYS_MEMTEST_START + 0x10000000) +
> > +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
> > +#define CONFIG_SYS_HZ 1000
> > +
> > +/* Physical Memory Map */
> > +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
> > +#define PHYS_SDRAM_SIZE SZ_256M
> > +
> > +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
> > +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
> > +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
> > +
> > +#define CONFIG_SYS_INIT_SP_OFFSET \
> > + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> > +#define CONFIG_SYS_INIT_SP_ADDR \
> > + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> > +
> > +#define CONFIG_ENV_SIZE (16 << 10)
> > +#define CONFIG_ENV_OFFSET (512 << 10)
> > +
> > +/* NAND */
> > +#define CONFIG_SYS_MAX_NAND_DEVICE 1
> > +#define CONFIG_SYS_NAND_BASE 0x40000000
> > +
> > +/* USB Configs */
> > +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
> > +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI |
> > PORT_PTS_PTW) +#define CONFIG_MXC_USB_FLAGS 0
> > +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
> > +
> > +#define CONFIG_IMX_THERMAL
> > +
> > +#define CONFIG_EXTRA_ENV_SETTINGS \
> > + "console=ttymxc0,115200n8\0" \
> > + "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
> > + "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
> > + "fdt_addr_r=0x82000000\0" \
> > + "fdt_high=0xffffffff\0" \
> > + "initrd_high=0xffffffff\0" \
> > + "kernel_addr_r=0x81000000\0" \
> > + "pxefile_addr_r=0x87100000\0" \
> > + "ramdisk_addr_r=0x82100000\0" \
> > + "scriptaddr=0x87000000\0" \
> > + BOOTENV
> > +
> > +#define BOOT_TARGET_DEVICES(func) \
> > + func(MMC, mmc, 0) \
> > + func(UBIFS, ubifs, 0) \
> > + func(DHCP, dhcp, na)
> > +
> > +#include <config_distro_bootcmd.h>
> > +
> > +#endif /* __PCL063_H */
>
>
>
> Best regards,
>
> Lukasz Majewski
>
> --
>
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
> lukma at denx.de
More information about the U-Boot
mailing list