[U-Boot] [PATCH 05/16] mtd: spi: Port SPI NOR framework from Linux
Vignesh R
vigneshr at ti.com
Wed Dec 12 17:32:17 UTC 2018
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
support 4 byte addressing opcodes, SFDP table parsing and different types of
quad mode enable sequences. Many newer flashes no longer support BANK
registers used by sf layer to a access >16MB space.
Also, many SPI controllers have special MMIO interfaces which provide
accelerated read/write access but require knowledge of flash parameters
to make use of it. Recent spi-mem layer provides a way to support such
flashes but sf layer isn't using that.
So sync SPI NOR framework from Linux v4.19 and add spi-mem support on top.
in order to gain 4 byte addressing support, SFDP support and a way to
support SPI controllers with MMIO flash interface.
Signed-off-by: Vignesh R <vigneshr at ti.com>
---
drivers/mtd/spi/spi-nor-core.c | 2647 ++++++++++++++++++++++++++++++++
include/linux/mtd/cfi.h | 32 +
include/linux/mtd/spi-nor.h | 421 +++++
3 files changed, 3100 insertions(+)
create mode 100644 drivers/mtd/spi/spi-nor-core.c
create mode 100644 include/linux/mtd/cfi.h
create mode 100644 include/linux/mtd/spi-nor.h
diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c
new file mode 100644
index 000000000000..4563cd74c2e8
--- /dev/null
+++ b/drivers/mtd/spi/spi-nor-core.c
@@ -0,0 +1,2647 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Based on m25p80.c, by Mike Lavender (mike at steroidmicros.com), with
+ * influence from lart.c (Abraham Van Der Merwe) and mtd_dataflash.c
+ *
+ * Copyright (C) 2005, Intec Automation Inc.
+ * Copyright (C) 2014, Freescale Semiconductor, Inc.
+ *
+ * Synced from Linux v4.19
+ */
+
+#include <common.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/log2.h>
+#include <linux/math64.h>
+#include <linux/sizes.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/spi-nor.h>
+#include <spi-mem.h>
+#include <spi.h>
+
+/* Define max times to check status register before we give up. */
+
+/*
+ * For everything but full-chip erase; probably could be much smaller, but kept
+ * around for safety for now
+ */
+
+#define HZ CONFIG_SYS_HZ
+
+#define DEFAULT_READY_WAIT_JIFFIES (40UL * HZ)
+
+#define SPI_NOR_MAX_ID_LEN 6
+#define SPI_NOR_MAX_ADDR_WIDTH 4
+
+struct flash_info {
+ char *name;
+
+ /*
+ * This array stores the ID bytes.
+ * The first three bytes are the JEDIC ID.
+ * JEDEC ID zero means "no ID" (mostly older chips).
+ */
+ u8 id[SPI_NOR_MAX_ID_LEN];
+ u8 id_len;
+
+ /* The size listed here is what works with SPINOR_OP_SE, which isn't
+ * necessarily called a "sector" by the vendor.
+ */
+ unsigned int sector_size;
+ u16 n_sectors;
+
+ u16 page_size;
+ u16 addr_width;
+
+ u16 flags;
+#define SECT_4K BIT(0) /* SPINOR_OP_BE_4K works uniformly */
+#define SPI_NOR_NO_ERASE BIT(1) /* No erase command needed */
+#define SST_WRITE BIT(2) /* use SST byte programming */
+#define SPI_NOR_NO_FR BIT(3) /* Can't do fastread */
+#define SECT_4K_PMC BIT(4) /* SPINOR_OP_BE_4K_PMC works uniformly */
+#define SPI_NOR_DUAL_READ BIT(5) /* Flash supports Dual Read */
+#define SPI_NOR_QUAD_READ BIT(6) /* Flash supports Quad Read */
+#define USE_FSR BIT(7) /* use flag status register */
+#define SPI_NOR_HAS_LOCK BIT(8) /* Flash supports lock/unlock via SR */
+#define SPI_NOR_HAS_TB BIT(9) /*
+ * Flash SR has Top/Bottom (TB) protect
+ * bit. Must be used with
+ * SPI_NOR_HAS_LOCK.
+ */
+#define SPI_S3AN BIT(10) /*
+ * Xilinx Spartan 3AN In-System Flash
+ * (MFR cannot be used for probing
+ * because it has the same value as
+ * ATMEL flashes)
+ */
+#define SPI_NOR_4B_OPCODES BIT(11) /*
+ * Use dedicated 4byte address op codes
+ * to support memory size above 128Mib.
+ */
+#define NO_CHIP_ERASE BIT(12) /* Chip does not support chip erase */
+#define SPI_NOR_SKIP_SFDP BIT(13) /* Skip parsing of SFDP tables */
+#define USE_CLSR BIT(14) /* use CLSR command */
+
+ int (*quad_enable)(struct spi_nor *nor);
+};
+
+#define JEDEC_MFR(info) ((info)->id[0])
+
+static int spi_nor_read_write_reg(struct spi_nor *nor, struct spi_mem_op
+ *op, void *buf)
+{
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ op->data.buf.in = buf;
+ else
+ op->data.buf.out = buf;
+ return spi_mem_exec_op(nor->spi, op);
+}
+
+static int spi_nor_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len)
+{
+ struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(code, 1),
+ SPI_MEM_OP_NO_ADDR,
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_IN(len, NULL, 1));
+ int ret;
+
+ ret = spi_nor_read_write_reg(nor, &op, val);
+ if (ret < 0)
+ dev_dbg(&flash->spimem->spi->dev, "error %d reading %x\n", ret,
+ code);
+
+ return ret;
+}
+
+static int spi_nor_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
+{
+ struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(opcode, 1),
+ SPI_MEM_OP_NO_ADDR,
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_OUT(len, NULL, 1));
+
+ return spi_nor_read_write_reg(nor, &op, buf);
+}
+
+static ssize_t spi_nor_read_data(struct spi_nor *nor, loff_t from, size_t len,
+ u_char *buf)
+{
+ struct spi_mem_op op =
+ SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 1),
+ SPI_MEM_OP_ADDR(nor->addr_width, from, 1),
+ SPI_MEM_OP_DUMMY(nor->read_dummy, 1),
+ SPI_MEM_OP_DATA_IN(len, buf, 1));
+ size_t remaining = len;
+ int ret;
+
+ /* get transfer protocols. */
+ op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->read_proto);
+ op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->read_proto);
+ op.dummy.buswidth = op.addr.buswidth;
+ op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->read_proto);
+
+ /* convert the dummy cycles to the number of bytes */
+ op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
+
+ while (remaining) {
+ op.data.nbytes = remaining < UINT_MAX ? remaining : UINT_MAX;
+ ret = spi_mem_adjust_op_size(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ ret = spi_mem_exec_op(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ op.addr.val += op.data.nbytes;
+ remaining -= op.data.nbytes;
+ op.data.buf.in += op.data.nbytes;
+ }
+
+ return len;
+}
+
+static ssize_t spi_nor_write_data(struct spi_nor *nor, loff_t to, size_t len,
+ const u_char *buf)
+{
+ struct spi_mem_op op =
+ SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 1),
+ SPI_MEM_OP_ADDR(nor->addr_width, to, 1),
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_OUT(len, buf, 1));
+ size_t remaining = len;
+ int ret;
+
+ /* get transfer protocols. */
+ op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->write_proto);
+ op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->write_proto);
+ op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->write_proto);
+
+ if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second)
+ op.addr.nbytes = 0;
+
+ while (remaining) {
+ op.data.nbytes = remaining < UINT_MAX ? remaining : UINT_MAX;
+ ret = spi_mem_adjust_op_size(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ ret = spi_mem_exec_op(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ op.addr.val += op.data.nbytes;
+ remaining -= op.data.nbytes;
+ op.data.buf.out += op.data.nbytes;
+ }
+
+ return len;
+}
+
+/*
+ * Read the status register, returning its value in the location
+ * Return the status register value.
+ * Returns negative if error occurred.
+ */
+static int read_sr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RDSR, &val, 1);
+ if (ret < 0) {
+ pr_debug("error %d reading SR\n", (int)ret);
+ return ret;
+ }
+
+ return val;
+}
+
+/*
+ * Read the flag status register, returning its value in the location
+ * Return the status register value.
+ * Returns negative if error occurred.
+ */
+static int read_fsr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RDFSR, &val, 1);
+ if (ret < 0) {
+ pr_debug("error %d reading FSR\n", ret);
+ return ret;
+ }
+
+ return val;
+}
+
+/*
+ * Read configuration register, returning its value in the
+ * location. Return the configuration register value.
+ * Returns negative if error occurred.
+ */
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+static int read_cr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RDCR, &val, 1);
+ if (ret < 0) {
+ dev_dbg(nor->dev, "error %d reading CR\n", ret);
+ return ret;
+ }
+
+ return val;
+}
+#endif
+
+/*
+ * Write status register 1 byte
+ * Returns negative if error occurred.
+ */
+static inline int write_sr(struct spi_nor *nor, u8 val)
+{
+ nor->cmd_buf[0] = val;
+ return nor->write_reg(nor, SPINOR_OP_WRSR, nor->cmd_buf, 1);
+}
+
+/*
+ * Set write enable latch with Write Enable command.
+ * Returns negative if error occurred.
+ */
+static inline int write_enable(struct spi_nor *nor)
+{
+ return nor->write_reg(nor, SPINOR_OP_WREN, NULL, 0);
+}
+
+/*
+ * Send write disable instruction to the chip.
+ */
+static inline int write_disable(struct spi_nor *nor)
+{
+ return nor->write_reg(nor, SPINOR_OP_WRDI, NULL, 0);
+}
+
+static inline struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd)
+{
+ return mtd->priv;
+}
+
+static u8 spi_nor_convert_opcode(u8 opcode, const u8 table[][2], size_t size)
+{
+ size_t i;
+
+ for (i = 0; i < size; i++)
+ if (table[i][0] == opcode)
+ return table[i][1];
+
+ /* No conversion found, keep input op code. */
+ return opcode;
+}
+
+static inline u8 spi_nor_convert_3to4_read(u8 opcode)
+{
+ static const u8 spi_nor_3to4_read[][2] = {
+ { SPINOR_OP_READ, SPINOR_OP_READ_4B },
+ { SPINOR_OP_READ_FAST, SPINOR_OP_READ_FAST_4B },
+ { SPINOR_OP_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B },
+ { SPINOR_OP_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B },
+ { SPINOR_OP_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B },
+ { SPINOR_OP_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B },
+ };
+
+ return spi_nor_convert_opcode(opcode, spi_nor_3to4_read,
+ ARRAY_SIZE(spi_nor_3to4_read));
+}
+
+static inline u8 spi_nor_convert_3to4_program(u8 opcode)
+{
+ static const u8 spi_nor_3to4_program[][2] = {
+ { SPINOR_OP_PP, SPINOR_OP_PP_4B },
+ { SPINOR_OP_PP_1_1_4, SPINOR_OP_PP_1_1_4_4B },
+ { SPINOR_OP_PP_1_4_4, SPINOR_OP_PP_1_4_4_4B },
+ };
+
+ return spi_nor_convert_opcode(opcode, spi_nor_3to4_program,
+ ARRAY_SIZE(spi_nor_3to4_program));
+}
+
+static inline u8 spi_nor_convert_3to4_erase(u8 opcode)
+{
+ static const u8 spi_nor_3to4_erase[][2] = {
+ { SPINOR_OP_BE_4K, SPINOR_OP_BE_4K_4B },
+ { SPINOR_OP_BE_32K, SPINOR_OP_BE_32K_4B },
+ { SPINOR_OP_SE, SPINOR_OP_SE_4B },
+ };
+
+ return spi_nor_convert_opcode(opcode, spi_nor_3to4_erase,
+ ARRAY_SIZE(spi_nor_3to4_erase));
+}
+
+static void spi_nor_set_4byte_opcodes(struct spi_nor *nor,
+ const struct flash_info *info)
+{
+ /* Do some manufacturer fixups first */
+ switch (JEDEC_MFR(info)) {
+ case SNOR_MFR_SPANSION:
+ /* No small sector erase for 4-byte command set */
+ nor->erase_opcode = SPINOR_OP_SE;
+ nor->mtd.erasesize = info->sector_size;
+ break;
+
+ default:
+ break;
+ }
+
+ nor->read_opcode = spi_nor_convert_3to4_read(nor->read_opcode);
+ nor->program_opcode = spi_nor_convert_3to4_program(nor->program_opcode);
+ nor->erase_opcode = spi_nor_convert_3to4_erase(nor->erase_opcode);
+}
+
+/* Enable/disable 4-byte addressing mode. */
+static inline int set_4byte(struct spi_nor *nor, const struct flash_info *info,
+ int enable)
+{
+ int status;
+ bool need_wren = false;
+ u8 cmd;
+
+ switch (JEDEC_MFR(info)) {
+ case SNOR_MFR_ST:
+ case SNOR_MFR_MICRON:
+ /* Some Micron need WREN command; all will accept it */
+ need_wren = true;
+ case SNOR_MFR_MACRONIX:
+ case SNOR_MFR_WINBOND:
+ if (need_wren)
+ write_enable(nor);
+
+ cmd = enable ? SPINOR_OP_EN4B : SPINOR_OP_EX4B;
+ status = nor->write_reg(nor, cmd, NULL, 0);
+ if (need_wren)
+ write_disable(nor);
+
+ if (!status && !enable &&
+ JEDEC_MFR(info) == SNOR_MFR_WINBOND) {
+ /*
+ * On Winbond W25Q256FV, leaving 4byte mode causes
+ * the Extended Address Register to be set to 1, so all
+ * 3-byte-address reads come from the second 16M.
+ * We must clear the register to enable normal behavior.
+ */
+ write_enable(nor);
+ nor->cmd_buf[0] = 0;
+ nor->write_reg(nor, SPINOR_OP_WREAR, nor->cmd_buf, 1);
+ write_disable(nor);
+ }
+
+ return status;
+ default:
+ /* Spansion style */
+ nor->cmd_buf[0] = enable << 7;
+ return nor->write_reg(nor, SPINOR_OP_BRWR, nor->cmd_buf, 1);
+ }
+}
+
+static int spi_nor_sr_ready(struct spi_nor *nor)
+{
+ int sr = read_sr(nor);
+
+ if (sr < 0)
+ return sr;
+
+#ifndef CONFIG_SPL_BUILD
+ if (nor->flags & SNOR_F_USE_CLSR && sr & (SR_E_ERR | SR_P_ERR)) {
+ if (sr & SR_E_ERR)
+ dev_dbg(nor->dev, "Erase Error occurred\n");
+ else
+ dev_dbg(nor->dev, "Programming Error occurred\n");
+
+ nor->write_reg(nor, SPINOR_OP_CLSR, NULL, 0);
+ return -EIO;
+ }
+#endif
+
+ return !(sr & SR_WIP);
+}
+
+static int spi_nor_fsr_ready(struct spi_nor *nor)
+{
+ int fsr = read_fsr(nor);
+
+ if (fsr < 0)
+ return fsr;
+#ifndef CONFIG_SPL_BUILD
+ if (fsr & (FSR_E_ERR | FSR_P_ERR)) {
+ if (fsr & FSR_E_ERR)
+ dev_dbg(nor->dev, "Erase operation failed.\n");
+ else
+ dev_dbg(nor->dev, "Program operation failed.\n");
+
+ if (fsr & FSR_PT_ERR)
+ dev_dbg(nor->dev,
+ "Attempted to modify a protected sector.\n");
+
+ nor->write_reg(nor, SPINOR_OP_CLFSR, NULL, 0);
+ return -EIO;
+ }
+#endif
+ return fsr & FSR_READY;
+}
+
+static int spi_nor_ready(struct spi_nor *nor)
+{
+ int sr, fsr;
+
+ sr = spi_nor_sr_ready(nor);
+ if (sr < 0)
+ return sr;
+ fsr = nor->flags & SNOR_F_USE_FSR ? spi_nor_fsr_ready(nor) : 1;
+ if (fsr < 0)
+ return fsr;
+ return sr && fsr;
+}
+
+/*
+ * Service routine to read status register until ready, or timeout occurs.
+ * Returns non-zero if error.
+ */
+static int spi_nor_wait_till_ready_with_timeout(struct spi_nor *nor,
+ unsigned long timeout)
+{
+ unsigned long timebase;
+ int ret;
+
+ timebase = get_timer(0);
+
+ while (get_timer(timebase) < timeout) {
+ ret = spi_nor_ready(nor);
+ if (ret < 0)
+ return ret;
+ if (ret)
+ return 0;
+ }
+
+ dev_err(nor->dev, "flash operation timed out\n");
+
+ return -ETIMEDOUT;
+}
+
+static int spi_nor_wait_till_ready(struct spi_nor *nor)
+{
+ return spi_nor_wait_till_ready_with_timeout(nor,
+ DEFAULT_READY_WAIT_JIFFIES);
+}
+
+/*
+ * Initiate the erasure of a single sector
+ */
+static int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
+{
+ u8 buf[SPI_NOR_MAX_ADDR_WIDTH];
+ int i;
+
+ if (nor->erase)
+ return nor->erase(nor, addr);
+
+ /*
+ * Default implementation, if driver doesn't have a specialized HW
+ * control
+ */
+ for (i = nor->addr_width - 1; i >= 0; i--) {
+ buf[i] = addr & 0xff;
+ addr >>= 8;
+ }
+
+ return nor->write_reg(nor, nor->erase_opcode, buf, nor->addr_width);
+}
+
+/*
+ * Erase an address range on the nor chip. The address range may extend
+ * one or more erase sectors. Return an error is there is a problem erasing.
+ */
+static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ u32 addr, len, rem;
+ int ret;
+
+ dev_dbg(nor->dev, "at 0x%llx, len %lld\n", (long long)instr->addr,
+ (long long)instr->len);
+
+ div_u64_rem(instr->len, mtd->erasesize, &rem);
+ if (rem)
+ return -EINVAL;
+
+ addr = instr->addr;
+ len = instr->len;
+
+ while (len) {
+ write_enable(nor);
+
+ ret = spi_nor_erase_sector(nor, addr);
+ if (ret)
+ goto erase_err;
+
+ addr += mtd->erasesize;
+ len -= mtd->erasesize;
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto erase_err;
+ }
+
+ write_disable(nor);
+
+erase_err:
+ return ret;
+}
+
+#if defined(CONFIG_SPI_FLASH_STMICRO) || defined(CONFIG_SPI_FLASH_SST)
+/* Write status register and ensure bits in mask match written values */
+static int write_sr_and_check(struct spi_nor *nor, u8 status_new, u8 mask)
+{
+ int ret;
+
+ write_enable(nor);
+ ret = write_sr(nor, status_new);
+ if (ret)
+ return ret;
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ return ret;
+
+ ret = read_sr(nor);
+ if (ret < 0)
+ return ret;
+
+ return ((ret & mask) != (status_new & mask)) ? -EIO : 0;
+}
+
+static void stm_get_locked_range(struct spi_nor *nor, u8 sr, loff_t *ofs,
+ uint64_t *len)
+{
+ struct mtd_info *mtd = &nor->mtd;
+ u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
+ int shift = ffs(mask) - 1;
+ int pow;
+
+ if (!(sr & mask)) {
+ /* No protection */
+ *ofs = 0;
+ *len = 0;
+ } else {
+ pow = ((sr & mask) ^ mask) >> shift;
+ *len = mtd->size >> pow;
+ if (nor->flags & SNOR_F_HAS_SR_TB && sr & SR_TB)
+ *ofs = 0;
+ else
+ *ofs = mtd->size - *len;
+ }
+}
+
+/*
+ * Return 1 if the entire region is locked (if @locked is true) or unlocked (if
+ * @locked is false); 0 otherwise
+ */
+static int stm_check_lock_status_sr(struct spi_nor *nor, loff_t ofs, u64 len,
+ u8 sr, bool locked)
+{
+ loff_t lock_offs;
+ uint64_t lock_len;
+
+ if (!len)
+ return 1;
+
+ stm_get_locked_range(nor, sr, &lock_offs, &lock_len);
+
+ if (locked)
+ /* Requested range is a sub-range of locked range */
+ return (ofs + len <= lock_offs + lock_len) && (ofs >= lock_offs);
+ else
+ /* Requested range does not overlap with locked range */
+ return (ofs >= lock_offs + lock_len) || (ofs + len <= lock_offs);
+}
+
+static int stm_is_locked_sr(struct spi_nor *nor, loff_t ofs, uint64_t len,
+ u8 sr)
+{
+ return stm_check_lock_status_sr(nor, ofs, len, sr, true);
+}
+
+static int stm_is_unlocked_sr(struct spi_nor *nor, loff_t ofs, uint64_t len,
+ u8 sr)
+{
+ return stm_check_lock_status_sr(nor, ofs, len, sr, false);
+}
+
+/*
+ * Lock a region of the flash. Compatible with ST Micro and similar flash.
+ * Supports the block protection bits BP{0,1,2} in the status register
+ * (SR). Does not support these features found in newer SR bitfields:
+ * - SEC: sector/block protect - only handle SEC=0 (block protect)
+ * - CMP: complement protect - only support CMP=0 (range is not complemented)
+ *
+ * Support for the following is provided conditionally for some flash:
+ * - TB: top/bottom protect
+ *
+ * Sample table portion for 8MB flash (Winbond w25q64fw):
+ *
+ * SEC | TB | BP2 | BP1 | BP0 | Prot Length | Protected Portion
+ * --------------------------------------------------------------------------
+ * X | X | 0 | 0 | 0 | NONE | NONE
+ * 0 | 0 | 0 | 0 | 1 | 128 KB | Upper 1/64
+ * 0 | 0 | 0 | 1 | 0 | 256 KB | Upper 1/32
+ * 0 | 0 | 0 | 1 | 1 | 512 KB | Upper 1/16
+ * 0 | 0 | 1 | 0 | 0 | 1 MB | Upper 1/8
+ * 0 | 0 | 1 | 0 | 1 | 2 MB | Upper 1/4
+ * 0 | 0 | 1 | 1 | 0 | 4 MB | Upper 1/2
+ * X | X | 1 | 1 | 1 | 8 MB | ALL
+ * ------|-------|-------|-------|-------|---------------|-------------------
+ * 0 | 1 | 0 | 0 | 1 | 128 KB | Lower 1/64
+ * 0 | 1 | 0 | 1 | 0 | 256 KB | Lower 1/32
+ * 0 | 1 | 0 | 1 | 1 | 512 KB | Lower 1/16
+ * 0 | 1 | 1 | 0 | 0 | 1 MB | Lower 1/8
+ * 0 | 1 | 1 | 0 | 1 | 2 MB | Lower 1/4
+ * 0 | 1 | 1 | 1 | 0 | 4 MB | Lower 1/2
+ *
+ * Returns negative on errors, 0 on success.
+ */
+static int stm_lock(struct spi_nor *nor, loff_t ofs, uint64_t len)
+{
+ struct mtd_info *mtd = &nor->mtd;
+ int status_old, status_new;
+ u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
+ u8 shift = ffs(mask) - 1, pow, val;
+ loff_t lock_len;
+ bool can_be_top = true, can_be_bottom = nor->flags & SNOR_F_HAS_SR_TB;
+ bool use_top;
+
+ status_old = read_sr(nor);
+ if (status_old < 0)
+ return status_old;
+
+ /* If nothing in our range is unlocked, we don't need to do anything */
+ if (stm_is_locked_sr(nor, ofs, len, status_old))
+ return 0;
+
+ /* If anything below us is unlocked, we can't use 'bottom' protection */
+ if (!stm_is_locked_sr(nor, 0, ofs, status_old))
+ can_be_bottom = false;
+
+ /* If anything above us is unlocked, we can't use 'top' protection */
+ if (!stm_is_locked_sr(nor, ofs + len, mtd->size - (ofs + len),
+ status_old))
+ can_be_top = false;
+
+ if (!can_be_bottom && !can_be_top)
+ return -EINVAL;
+
+ /* Prefer top, if both are valid */
+ use_top = can_be_top;
+
+ /* lock_len: length of region that should end up locked */
+ if (use_top)
+ lock_len = mtd->size - ofs;
+ else
+ lock_len = ofs + len;
+
+ /*
+ * Need smallest pow such that:
+ *
+ * 1 / (2^pow) <= (len / size)
+ *
+ * so (assuming power-of-2 size) we do:
+ *
+ * pow = ceil(log2(size / len)) = log2(size) - floor(log2(len))
+ */
+ pow = ilog2(mtd->size) - ilog2(lock_len);
+ val = mask - (pow << shift);
+ if (val & ~mask)
+ return -EINVAL;
+ /* Don't "lock" with no region! */
+ if (!(val & mask))
+ return -EINVAL;
+
+ status_new = (status_old & ~mask & ~SR_TB) | val;
+
+ /* Disallow further writes if WP pin is asserted */
+ status_new |= SR_SRWD;
+
+ if (!use_top)
+ status_new |= SR_TB;
+
+ /* Don't bother if they're the same */
+ if (status_new == status_old)
+ return 0;
+
+ /* Only modify protection if it will not unlock other areas */
+ if ((status_new & mask) < (status_old & mask))
+ return -EINVAL;
+
+ return write_sr_and_check(nor, status_new, mask);
+}
+
+/*
+ * Unlock a region of the flash. See stm_lock() for more info
+ *
+ * Returns negative on errors, 0 on success.
+ */
+static int stm_unlock(struct spi_nor *nor, loff_t ofs, uint64_t len)
+{
+ struct mtd_info *mtd = &nor->mtd;
+ int status_old, status_new;
+ u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
+ u8 shift = ffs(mask) - 1, pow, val;
+ loff_t lock_len;
+ bool can_be_top = true, can_be_bottom = nor->flags & SNOR_F_HAS_SR_TB;
+ bool use_top;
+
+ status_old = read_sr(nor);
+ if (status_old < 0)
+ return status_old;
+
+ /* If nothing in our range is locked, we don't need to do anything */
+ if (stm_is_unlocked_sr(nor, ofs, len, status_old))
+ return 0;
+
+ /* If anything below us is locked, we can't use 'top' protection */
+ if (!stm_is_unlocked_sr(nor, 0, ofs, status_old))
+ can_be_top = false;
+
+ /* If anything above us is locked, we can't use 'bottom' protection */
+ if (!stm_is_unlocked_sr(nor, ofs + len, mtd->size - (ofs + len),
+ status_old))
+ can_be_bottom = false;
+
+ if (!can_be_bottom && !can_be_top)
+ return -EINVAL;
+
+ /* Prefer top, if both are valid */
+ use_top = can_be_top;
+
+ /* lock_len: length of region that should remain locked */
+ if (use_top)
+ lock_len = mtd->size - (ofs + len);
+ else
+ lock_len = ofs;
+
+ /*
+ * Need largest pow such that:
+ *
+ * 1 / (2^pow) >= (len / size)
+ *
+ * so (assuming power-of-2 size) we do:
+ *
+ * pow = floor(log2(size / len)) = log2(size) - ceil(log2(len))
+ */
+ pow = ilog2(mtd->size) - order_base_2(lock_len);
+ if (lock_len == 0) {
+ val = 0; /* fully unlocked */
+ } else {
+ val = mask - (pow << shift);
+ /* Some power-of-two sizes are not supported */
+ if (val & ~mask)
+ return -EINVAL;
+ }
+
+ status_new = (status_old & ~mask & ~SR_TB) | val;
+
+ /* Don't protect status register if we're fully unlocked */
+ if (lock_len == 0)
+ status_new &= ~SR_SRWD;
+
+ if (!use_top)
+ status_new |= SR_TB;
+
+ /* Don't bother if they're the same */
+ if (status_new == status_old)
+ return 0;
+
+ /* Only modify protection if it will not lock other areas */
+ if ((status_new & mask) > (status_old & mask))
+ return -EINVAL;
+
+ return write_sr_and_check(nor, status_new, mask);
+}
+
+/*
+ * Check if a region of the flash is (completely) locked. See stm_lock() for
+ * more info.
+ *
+ * Returns 1 if entire region is locked, 0 if any portion is unlocked, and
+ * negative on errors.
+ */
+static int stm_is_locked(struct spi_nor *nor, loff_t ofs, uint64_t len)
+{
+ int status;
+
+ status = read_sr(nor);
+ if (status < 0)
+ return status;
+
+ return stm_is_locked_sr(nor, ofs, len, status);
+}
+#endif /* CONFIG_SPI_FLASH_STMICRO */
+
+static int spi_nor_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ int ret;
+
+ ret = nor->flash_lock(nor, ofs, len);
+
+ return ret;
+}
+
+static int spi_nor_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ int ret;
+
+ ret = nor->flash_unlock(nor, ofs, len);
+
+ return ret;
+}
+
+static int spi_nor_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ int ret;
+
+ ret = nor->flash_is_locked(nor, ofs, len);
+
+ return ret;
+}
+
+/* Used when the "_ext_id" is two bytes at most */
+#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
+ .id = { \
+ ((_jedec_id) >> 16) & 0xff, \
+ ((_jedec_id) >> 8) & 0xff, \
+ (_jedec_id) & 0xff, \
+ ((_ext_id) >> 8) & 0xff, \
+ (_ext_id) & 0xff, \
+ }, \
+ .id_len = (!(_jedec_id) ? 0 : (3 + ((_ext_id) ? 2 : 0))), \
+ .sector_size = (_sector_size), \
+ .n_sectors = (_n_sectors), \
+ .page_size = 256, \
+ .flags = (_flags),
+
+#define INFO6(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
+ .id = { \
+ ((_jedec_id) >> 16) & 0xff, \
+ ((_jedec_id) >> 8) & 0xff, \
+ (_jedec_id) & 0xff, \
+ ((_ext_id) >> 16) & 0xff, \
+ ((_ext_id) >> 8) & 0xff, \
+ (_ext_id) & 0xff, \
+ }, \
+ .id_len = 6, \
+ .sector_size = (_sector_size), \
+ .n_sectors = (_n_sectors), \
+ .page_size = 256, \
+ .flags = (_flags),
+
+/* NOTE: double check command sets and memory organization when you add
+ * more nor chips. This current list focusses on newer chips, which
+ * have been converging on command sets which including JEDEC ID.
+ *
+ * All newly added entries should describe *hardware* and should use SECT_4K
+ * (or SECT_4K_PMC) if hardware supports erasing 4 KiB sectors. For usage
+ * scenarios excluding small sectors there is config option that can be
+ * disabled: CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.
+ * For historical (and compatibility) reasons (before we got above config) some
+ * old entries may be missing 4K flag.
+ */
+const struct flash_info spi_nor_ids[] = {
+#ifdef CONFIG_SPI_FLASH_ATMEL /* ATMEL */
+ /* Atmel -- some are (confusingly) marketed as "DataFlash" */
+ { "at26df321", INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) },
+ { "at25df321a", INFO(0x1f4701, 0, 64 * 1024, 64, SECT_4K) },
+
+ { "at45db011d", INFO(0x1f2200, 0, 64 * 1024, 4, SECT_4K) },
+ { "at45db021d", INFO(0x1f2300, 0, 64 * 1024, 8, SECT_4K) },
+ { "at45db041d", INFO(0x1f2400, 0, 64 * 1024, 8, SECT_4K) },
+ { "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) },
+ { "at45db161d", INFO(0x1f2600, 0, 64 * 1024, 32, SECT_4K) },
+ { "at45db321d", INFO(0x1f2700, 0, 64 * 1024, 64, SECT_4K) },
+ { "at45db641d", INFO(0x1f2800, 0, 64 * 1024, 128, SECT_4K) },
+ { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) },
+#endif
+#ifdef CONFIG_SPI_FLASH_EON /* EON */
+ /* EON -- en25xxx */
+ { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) },
+ { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) },
+ { "en25qh128", INFO(0x1c7018, 0, 64 * 1024, 256, 0) },
+ { "en25s64", INFO(0x1c3817, 0, 64 * 1024, 128, SECT_4K) },
+#endif
+#ifdef CONFIG_SPI_FLASH_GIGADEVICE /* GIGADEVICE */
+ /* GigaDevice */
+ {
+ "gd25q16", INFO(0xc84015, 0, 64 * 1024, 32,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ "gd25q32", INFO(0xc84016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ "gd25lq32", INFO(0xc86016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ "gd25q64", INFO(0xc84017, 0, 64 * 1024, 128,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+#endif
+#ifdef CONFIG_SPI_FLASH_ISSI /* ISSI */
+ /* ISSI */
+ { "is25lq040b", INFO(0x9d4013, 0, 64 * 1024, 8,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "is25lp032", INFO(0x9d6016, 0, 64 * 1024, 64, 0) },
+ { "is25lp064", INFO(0x9d6017, 0, 64 * 1024, 128, 0) },
+ { "is25lp128", INFO(0x9d6018, 0, 64 * 1024, 256,
+ SECT_4K | SPI_NOR_DUAL_READ) },
+ { "is25lp256", INFO(0x9d6019, 0, 64 * 1024, 512,
+ SECT_4K | SPI_NOR_DUAL_READ) },
+ { "is25wp032", INFO(0x9d7016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "is25wp064", INFO(0x9d7017, 0, 64 * 1024, 128,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "is25wp128", INFO(0x9d7018, 0, 64 * 1024, 256,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+#endif
+#ifdef CONFIG_SPI_FLASH_MACRONIX /* MACRONIX */
+ /* Macronix */
+ { "mx25l2005a", INFO(0xc22012, 0, 64 * 1024, 4, SECT_4K) },
+ { "mx25l4005a", INFO(0xc22013, 0, 64 * 1024, 8, SECT_4K) },
+ { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) },
+ { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) },
+ { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, SECT_4K) },
+ { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, SECT_4K) },
+ { "mx25u2033e", INFO(0xc22532, 0, 64 * 1024, 4, SECT_4K) },
+ { "mx25u1635e", INFO(0xc22535, 0, 64 * 1024, 32, SECT_4K) },
+ { "mx25u6435f", INFO(0xc22537, 0, 64 * 1024, 128, SECT_4K) },
+ { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
+ { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
+ { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "mx25u25635f", INFO(0xc22539, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_4B_OPCODES) },
+ { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
+ { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+ { "mx66u51235f", INFO(0xc2253a, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+ { "mx66l1g45g", INFO(0xc2201b, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "mx25l1633e", INFO(0xc22415, 0, 64 * 1024, 32, SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES | SECT_4K) },
+#endif
+
+#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
+ /* Micron */
+ { "n25q016a", INFO(0x20bb15, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
+ { "n25q032a", INFO(0x20bb16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
+ { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q064a", INFO(0x20bb17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "n25q256ax1", INFO(0x20bb19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
+ { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
+ { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
+ { "n25q00a", INFO(0x20bb21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
+ { "mt25qu02g", INFO(0x20bb22, 0, 64 * 1024, 4096, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
+#endif
+#ifdef CONFIG_SPI_FLASH_SPANSION /* SPANSION */
+ /* Spansion/Cypress -- single (large) sector size only, at least
+ * for the chips listed here (without boot sectors).
+ */
+ { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR) },
+ { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl512s", INFO6(0x010220, 0x4d0081, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl512s_256k", INFO(0x010220, 0x4d00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl512s_64k", INFO(0x010220, 0x4d01, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl512s_512k", INFO(0x010220, 0x4f00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
+ { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
+ { "s25fl128s", INFO6(0x012018, 0x4d0180, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
+ { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
+ { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) },
+ { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) },
+ { "s25fl116k", INFO(0x014015, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "s25fl164k", INFO(0x014017, 0, 64 * 1024, 128, SECT_4K) },
+ { "s25fl208k", INFO(0x014014, 0, 64 * 1024, 16, SECT_4K | SPI_NOR_DUAL_READ) },
+ { "s25fl128l", INFO(0x016018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+#endif
+#ifdef CONFIG_SPI_FLASH_SST /* SST */
+ /* SST -- large erase sizes are "overlays", "sectors" are 4K */
+ { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
+ { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
+ { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K | SST_WRITE) },
+ { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K | SST_WRITE) },
+ { "sst25vf064c", INFO(0xbf254b, 0, 64 * 1024, 128, SECT_4K) },
+ { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1, SECT_4K | SST_WRITE) },
+ { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2, SECT_4K | SST_WRITE) },
+ { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4, SECT_4K | SST_WRITE) },
+ { "sst25wf020a", INFO(0x621612, 0, 64 * 1024, 4, SECT_4K) },
+ { "sst25wf040b", INFO(0x621613, 0, 64 * 1024, 8, SECT_4K) },
+ { "sst25wf040", INFO(0xbf2504, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
+ { "sst25wf080", INFO(0xbf2505, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
+ { "sst26vf064b", INFO(0xbf2643, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "sst26wf016", INFO(0xbf2651, 0, 64 * 1024, 32, SECT_4K) },
+ { "sst26wf032", INFO(0xbf2622, 0, 64 * 1024, 64, SECT_4K) },
+ { "sst26wf064", INFO(0xbf2643, 0, 64 * 1024, 128, SECT_4K) },
+#endif
+#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
+ /* ST Microelectronics -- newer production may have feature updates */
+ { "m25p10", INFO(0x202011, 0, 32 * 1024, 4, 0) },
+ { "m25p20", INFO(0x202012, 0, 64 * 1024, 4, 0) },
+ { "m25p40", INFO(0x202013, 0, 64 * 1024, 8, 0) },
+ { "m25p80", INFO(0x202014, 0, 64 * 1024, 16, 0) },
+ { "m25p16", INFO(0x202015, 0, 64 * 1024, 32, 0) },
+ { "m25p32", INFO(0x202016, 0, 64 * 1024, 64, 0) },
+ { "m25p64", INFO(0x202017, 0, 64 * 1024, 128, 0) },
+ { "m25p128", INFO(0x202018, 0, 256 * 1024, 64, 0) },
+ { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) },
+ { "m25px16", INFO(0x207115, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "m25px64", INFO(0x207117, 0, 64 * 1024, 128, 0) },
+#endif
+#ifdef CONFIG_SPI_FLASH_WINBOND /* WINBOND */
+ /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
+ { "w25x05", INFO(0xef3010, 0, 64 * 1024, 1, SECT_4K) },
+ { "w25x10", INFO(0xef3011, 0, 64 * 1024, 2, SECT_4K) },
+ { "w25x20", INFO(0xef3012, 0, 64 * 1024, 4, SECT_4K) },
+ { "w25x40", INFO(0xef3013, 0, 64 * 1024, 8, SECT_4K) },
+ { "w25x80", INFO(0xef3014, 0, 64 * 1024, 16, SECT_4K) },
+ { "w25x16", INFO(0xef3015, 0, 64 * 1024, 32, SECT_4K) },
+ {
+ "w25q16dw", INFO(0xef6015, 0, 64 * 1024, 32,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ { "w25x32", INFO(0xef3016, 0, 64 * 1024, 64, SECT_4K) },
+ { "w25q20cl", INFO(0xef4012, 0, 64 * 1024, 4, SECT_4K) },
+ { "w25q20bw", INFO(0xef5012, 0, 64 * 1024, 4, SECT_4K) },
+ { "w25q20ew", INFO(0xef6012, 0, 64 * 1024, 4, SECT_4K) },
+ { "w25q32", INFO(0xef4016, 0, 64 * 1024, 64, SECT_4K) },
+ {
+ "w25q32dw", INFO(0xef6016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ "w25q32jv", INFO(0xef7016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
+ { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
+ {
+ "w25q64dw", INFO(0xef6017, 0, 64 * 1024, 128,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ "w25q128fw", INFO(0xef6018, 0, 64 * 1024, 256,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) },
+ { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) },
+ { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) },
+ { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024,
+ SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ) },
+#endif
+#ifdef CONFIG_SPI_FLASH_XMC
+ /* XMC (Wuhan Xinxin Semiconductor Manufacturing Corp.) */
+ { "XM25QH64A", INFO(0x207017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "XM25QH128A", INFO(0x207018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+#endif
+ { },
+};
+
+static const struct flash_info *spi_nor_read_id(struct spi_nor *nor)
+{
+ int tmp;
+ u8 id[SPI_NOR_MAX_ID_LEN];
+ const struct flash_info *info;
+
+ if (!ARRAY_SIZE(spi_nor_ids))
+ return ERR_PTR(-ENODEV);
+
+ tmp = nor->read_reg(nor, SPINOR_OP_RDID, id, SPI_NOR_MAX_ID_LEN);
+ if (tmp < 0) {
+ dev_dbg(nor->dev, "error %d reading JEDEC ID\n", tmp);
+ return ERR_PTR(tmp);
+ }
+
+ for (tmp = 0; tmp < ARRAY_SIZE(spi_nor_ids) - 1; tmp++) {
+ info = &spi_nor_ids[tmp];
+ if (info->id_len) {
+ if (!memcmp(info->id, id, info->id_len))
+ return &spi_nor_ids[tmp];
+ }
+ }
+ dev_err(nor->dev, "unrecognized JEDEC id bytes: %02x, %02x, %02x\n",
+ id[0], id[1], id[2]);
+ return ERR_PTR(-ENODEV);
+}
+
+static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ int ret;
+
+ dev_dbg(nor->dev, "from 0x%08x, len %zd\n", (u32)from, len);
+
+ while (len) {
+ loff_t addr = from;
+
+ ret = nor->read(nor, addr, len, buf);
+ if (ret == 0) {
+ /* We shouldn't see 0-length reads */
+ ret = -EIO;
+ goto read_err;
+ }
+ if (ret < 0)
+ goto read_err;
+
+ *retlen += ret;
+ buf += ret;
+ from += ret;
+ len -= ret;
+ }
+ ret = 0;
+
+read_err:
+ return ret;
+}
+
+#ifdef CONFIG_SPI_FLASH_SST
+static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ size_t actual;
+ int ret;
+
+ dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+
+ write_enable(nor);
+
+ nor->sst_write_second = false;
+
+ actual = to % 2;
+ /* Start write from odd address. */
+ if (actual) {
+ nor->program_opcode = SPINOR_OP_BP;
+
+ /* write one byte. */
+ ret = nor->write(nor, to, 1, buf);
+ if (ret < 0)
+ goto sst_write_err;
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto sst_write_err;
+ }
+ to += actual;
+
+ /* Write out most of the data here. */
+ for (; actual < len - 1; actual += 2) {
+ nor->program_opcode = SPINOR_OP_AAI_WP;
+
+ /* write two bytes. */
+ ret = nor->write(nor, to, 2, buf + actual);
+ if (ret < 0)
+ goto sst_write_err;
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto sst_write_err;
+ to += 2;
+ nor->sst_write_second = true;
+ }
+ nor->sst_write_second = false;
+
+ write_disable(nor);
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto sst_write_err;
+
+ /* Write out trailing byte if it exists. */
+ if (actual != len) {
+ write_enable(nor);
+
+ nor->program_opcode = SPINOR_OP_BP;
+ ret = nor->write(nor, to, 1, buf + actual);
+ if (ret < 0)
+ goto sst_write_err;
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto sst_write_err;
+ write_disable(nor);
+ actual += 1;
+ }
+sst_write_err:
+ *retlen += actual;
+ return ret;
+}
+#endif
+/*
+ * Write an address range to the nor chip. Data must be written in
+ * FLASH_PAGESIZE chunks. The address range may be any size provided
+ * it is within the physical boundaries.
+ */
+static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ size_t page_offset, page_remain, i;
+ ssize_t ret;
+
+ dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+
+ for (i = 0; i < len; ) {
+ ssize_t written;
+ loff_t addr = to + i;
+
+ /*
+ * If page_size is a power of two, the offset can be quickly
+ * calculated with an AND operation. On the other cases we
+ * need to do a modulus operation (more expensive).
+ * Power of two numbers have only one bit set and we can use
+ * the instruction hweight32 to detect if we need to do a
+ * modulus (do_div()) or not.
+ */
+ if (hweight32(nor->page_size) == 1) {
+ page_offset = addr & (nor->page_size - 1);
+ } else {
+ u64 aux = addr;
+
+ page_offset = do_div(aux, nor->page_size);
+ }
+ /* the size of data remaining on the first page */
+ page_remain = min_t(size_t,
+ nor->page_size - page_offset, len - i);
+
+ write_enable(nor);
+ ret = nor->write(nor, addr, page_remain, buf + i);
+ if (ret < 0)
+ goto write_err;
+ written = ret;
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto write_err;
+ *retlen += written;
+ i += written;
+ if (written != page_remain) {
+ dev_dbg(nor->dev,
+ "While writing %zu bytes written %zd bytes\n",
+ page_remain, written);
+ ret = -EIO;
+ goto write_err;
+ }
+ }
+
+write_err:
+ return ret;
+}
+
+#ifdef CONFIG_SPI_FLASH_MACRONIX
+/**
+ * macronix_quad_enable() - set QE bit in Status Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Status Register.
+ *
+ * bit 6 of the Status Register is the QE bit for Macronix like QSPI memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int macronix_quad_enable(struct spi_nor *nor)
+{
+ int ret, val;
+
+ val = read_sr(nor);
+ if (val < 0)
+ return val;
+ if (val & SR_QUAD_EN_MX)
+ return 0;
+
+ write_enable(nor);
+
+ write_sr(nor, val | SR_QUAD_EN_MX);
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ return ret;
+
+ ret = read_sr(nor);
+ if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) {
+ dev_err(nor->dev, "Macronix Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+/*
+ * Write status Register and configuration register with 2 bytes
+ * The first byte will be written to the status register, while the
+ * second byte will be written to the configuration register.
+ * Return negative if error occurred.
+ */
+static int write_sr_cr(struct spi_nor *nor, u8 *sr_cr)
+{
+ int ret;
+
+ write_enable(nor);
+
+ ret = nor->write_reg(nor, SPINOR_OP_WRSR, sr_cr, 2);
+ if (ret < 0) {
+ dev_dbg(nor->dev,
+ "error while writing configuration register\n");
+ return -EINVAL;
+ }
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret) {
+ dev_dbg(nor->dev,
+ "timeout while writing configuration register\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+/**
+ * spansion_read_cr_quad_enable() - set QE bit in Configuration Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Configuration Register.
+ * This function should be used with QSPI memories supporting the Read
+ * Configuration Register (35h) instruction.
+ *
+ * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
+ * memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spansion_read_cr_quad_enable(struct spi_nor *nor)
+{
+ u8 sr_cr[2];
+ int ret;
+
+ /* Check current Quad Enable bit value. */
+ ret = read_cr(nor);
+ if (ret < 0) {
+ dev_dbg(dev, "error while reading configuration register\n");
+ return -EINVAL;
+ }
+
+ if (ret & CR_QUAD_EN_SPAN)
+ return 0;
+
+ sr_cr[1] = ret | CR_QUAD_EN_SPAN;
+
+ /* Keep the current value of the Status Register. */
+ ret = read_sr(nor);
+ if (ret < 0) {
+ dev_dbg(dev, "error while reading status register\n");
+ return -EINVAL;
+ }
+ sr_cr[0] = ret;
+
+ ret = write_sr_cr(nor, sr_cr);
+ if (ret)
+ return ret;
+
+ /* Read back and check it. */
+ ret = read_cr(nor);
+ if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) {
+ dev_dbg(nor->dev, "Spansion Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+#if CONFIG_IS_ENABLED(SPI_FLASH_SFDP_SUPPORT)
+/**
+ * spansion_no_read_cr_quad_enable() - set QE bit in Configuration Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Configuration Register.
+ * This function should be used with QSPI memories not supporting the Read
+ * Configuration Register (35h) instruction.
+ *
+ * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
+ * memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spansion_no_read_cr_quad_enable(struct spi_nor *nor)
+{
+ u8 sr_cr[2];
+ int ret;
+
+ /* Keep the current value of the Status Register. */
+ ret = read_sr(nor);
+ if (ret < 0) {
+ dev_dbg(nor->dev, "error while reading status register\n");
+ return -EINVAL;
+ }
+ sr_cr[0] = ret;
+ sr_cr[1] = CR_QUAD_EN_SPAN;
+
+ return write_sr_cr(nor, sr_cr);
+}
+
+#endif /* CONFIG_SPI_FLASH_SFDP_SUPPORT */
+#endif /* CONFIG_SPI_FLASH_SPANSION */
+
+struct spi_nor_read_command {
+ u8 num_mode_clocks;
+ u8 num_wait_states;
+ u8 opcode;
+ enum spi_nor_protocol proto;
+};
+
+struct spi_nor_pp_command {
+ u8 opcode;
+ enum spi_nor_protocol proto;
+};
+
+enum spi_nor_read_command_index {
+ SNOR_CMD_READ,
+ SNOR_CMD_READ_FAST,
+ SNOR_CMD_READ_1_1_1_DTR,
+
+ /* Dual SPI */
+ SNOR_CMD_READ_1_1_2,
+ SNOR_CMD_READ_1_2_2,
+ SNOR_CMD_READ_2_2_2,
+ SNOR_CMD_READ_1_2_2_DTR,
+
+ /* Quad SPI */
+ SNOR_CMD_READ_1_1_4,
+ SNOR_CMD_READ_1_4_4,
+ SNOR_CMD_READ_4_4_4,
+ SNOR_CMD_READ_1_4_4_DTR,
+
+ /* Octo SPI */
+ SNOR_CMD_READ_1_1_8,
+ SNOR_CMD_READ_1_8_8,
+ SNOR_CMD_READ_8_8_8,
+ SNOR_CMD_READ_1_8_8_DTR,
+
+ SNOR_CMD_READ_MAX
+};
+
+enum spi_nor_pp_command_index {
+ SNOR_CMD_PP,
+
+ /* Quad SPI */
+ SNOR_CMD_PP_1_1_4,
+ SNOR_CMD_PP_1_4_4,
+ SNOR_CMD_PP_4_4_4,
+
+ /* Octo SPI */
+ SNOR_CMD_PP_1_1_8,
+ SNOR_CMD_PP_1_8_8,
+ SNOR_CMD_PP_8_8_8,
+
+ SNOR_CMD_PP_MAX
+};
+
+struct spi_nor_flash_parameter {
+ u64 size;
+ u32 page_size;
+
+ struct spi_nor_hwcaps hwcaps;
+ struct spi_nor_read_command reads[SNOR_CMD_READ_MAX];
+ struct spi_nor_pp_command page_programs[SNOR_CMD_PP_MAX];
+
+ int (*quad_enable)(struct spi_nor *nor);
+};
+
+static void
+spi_nor_set_read_settings(struct spi_nor_read_command *read,
+ u8 num_mode_clocks,
+ u8 num_wait_states,
+ u8 opcode,
+ enum spi_nor_protocol proto)
+{
+ read->num_mode_clocks = num_mode_clocks;
+ read->num_wait_states = num_wait_states;
+ read->opcode = opcode;
+ read->proto = proto;
+}
+
+static void
+spi_nor_set_pp_settings(struct spi_nor_pp_command *pp,
+ u8 opcode,
+ enum spi_nor_protocol proto)
+{
+ pp->opcode = opcode;
+ pp->proto = proto;
+}
+
+#if CONFIG_IS_ENABLED(SPI_FLASH_SFDP_SUPPORT)
+/*
+ * Serial Flash Discoverable Parameters (SFDP) parsing.
+ */
+
+/**
+ * spi_nor_read_sfdp() - read Serial Flash Discoverable Parameters.
+ * @nor: pointer to a 'struct spi_nor'
+ * @addr: offset in the SFDP area to start reading data from
+ * @len: number of bytes to read
+ * @buf: buffer where the SFDP data are copied into (dma-safe memory)
+ *
+ * Whatever the actual numbers of bytes for address and dummy cycles are
+ * for (Fast) Read commands, the Read SFDP (5Ah) instruction is always
+ * followed by a 3-byte address and 8 dummy clock cycles.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr,
+ size_t len, void *buf)
+{
+ u8 addr_width, read_opcode, read_dummy;
+ int ret;
+
+ read_opcode = nor->read_opcode;
+ addr_width = nor->addr_width;
+ read_dummy = nor->read_dummy;
+
+ nor->read_opcode = SPINOR_OP_RDSFDP;
+ nor->addr_width = 3;
+ nor->read_dummy = 8;
+
+ while (len) {
+ ret = nor->read(nor, addr, len, (u8 *)buf);
+ if (!ret || ret > len) {
+ ret = -EIO;
+ goto read_err;
+ }
+ if (ret < 0)
+ goto read_err;
+
+ buf += ret;
+ addr += ret;
+ len -= ret;
+ }
+ ret = 0;
+
+read_err:
+ nor->read_opcode = read_opcode;
+ nor->addr_width = addr_width;
+ nor->read_dummy = read_dummy;
+
+ return ret;
+}
+
+struct sfdp_parameter_header {
+ u8 id_lsb;
+ u8 minor;
+ u8 major;
+ u8 length; /* in double words */
+ u8 parameter_table_pointer[3]; /* byte address */
+ u8 id_msb;
+};
+
+#define SFDP_PARAM_HEADER_ID(p) (((p)->id_msb << 8) | (p)->id_lsb)
+#define SFDP_PARAM_HEADER_PTP(p) \
+ (((p)->parameter_table_pointer[2] << 16) | \
+ ((p)->parameter_table_pointer[1] << 8) | \
+ ((p)->parameter_table_pointer[0] << 0))
+
+#define SFDP_BFPT_ID 0xff00 /* Basic Flash Parameter Table */
+#define SFDP_SECTOR_MAP_ID 0xff81 /* Sector Map Table */
+
+#define SFDP_SIGNATURE 0x50444653U
+#define SFDP_JESD216_MAJOR 1
+#define SFDP_JESD216_MINOR 0
+#define SFDP_JESD216A_MINOR 5
+#define SFDP_JESD216B_MINOR 6
+
+struct sfdp_header {
+ u32 signature; /* Ox50444653U <=> "SFDP" */
+ u8 minor;
+ u8 major;
+ u8 nph; /* 0-base number of parameter headers */
+ u8 unused;
+
+ /* Basic Flash Parameter Table. */
+ struct sfdp_parameter_header bfpt_header;
+};
+
+/* Basic Flash Parameter Table */
+
+/*
+ * JESD216 rev B defines a Basic Flash Parameter Table of 16 DWORDs.
+ * They are indexed from 1 but C arrays are indexed from 0.
+ */
+#define BFPT_DWORD(i) ((i) - 1)
+#define BFPT_DWORD_MAX 16
+
+/* The first version of JESB216 defined only 9 DWORDs. */
+#define BFPT_DWORD_MAX_JESD216 9
+
+/* 1st DWORD. */
+#define BFPT_DWORD1_FAST_READ_1_1_2 BIT(16)
+#define BFPT_DWORD1_ADDRESS_BYTES_MASK GENMASK(18, 17)
+#define BFPT_DWORD1_ADDRESS_BYTES_3_ONLY (0x0UL << 17)
+#define BFPT_DWORD1_ADDRESS_BYTES_3_OR_4 (0x1UL << 17)
+#define BFPT_DWORD1_ADDRESS_BYTES_4_ONLY (0x2UL << 17)
+#define BFPT_DWORD1_DTR BIT(19)
+#define BFPT_DWORD1_FAST_READ_1_2_2 BIT(20)
+#define BFPT_DWORD1_FAST_READ_1_4_4 BIT(21)
+#define BFPT_DWORD1_FAST_READ_1_1_4 BIT(22)
+
+/* 5th DWORD. */
+#define BFPT_DWORD5_FAST_READ_2_2_2 BIT(0)
+#define BFPT_DWORD5_FAST_READ_4_4_4 BIT(4)
+
+/* 11th DWORD. */
+#define BFPT_DWORD11_PAGE_SIZE_SHIFT 4
+#define BFPT_DWORD11_PAGE_SIZE_MASK GENMASK(7, 4)
+
+/* 15th DWORD. */
+
+/*
+ * (from JESD216 rev B)
+ * Quad Enable Requirements (QER):
+ * - 000b: Device does not have a QE bit. Device detects 1-1-4 and 1-4-4
+ * reads based on instruction. DQ3/HOLD# functions are hold during
+ * instruction phase.
+ * - 001b: QE is bit 1 of status register 2. It is set via Write Status with
+ * two data bytes where bit 1 of the second byte is one.
+ * [...]
+ * Writing only one byte to the status register has the side-effect of
+ * clearing status register 2, including the QE bit. The 100b code is
+ * used if writing one byte to the status register does not modify
+ * status register 2.
+ * - 010b: QE is bit 6 of status register 1. It is set via Write Status with
+ * one data byte where bit 6 is one.
+ * [...]
+ * - 011b: QE is bit 7 of status register 2. It is set via Write status
+ * register 2 instruction 3Eh with one data byte where bit 7 is one.
+ * [...]
+ * The status register 2 is read using instruction 3Fh.
+ * - 100b: QE is bit 1 of status register 2. It is set via Write Status with
+ * two data bytes where bit 1 of the second byte is one.
+ * [...]
+ * In contrast to the 001b code, writing one byte to the status
+ * register does not modify status register 2.
+ * - 101b: QE is bit 1 of status register 2. Status register 1 is read using
+ * Read Status instruction 05h. Status register2 is read using
+ * instruction 35h. QE is set via Writ Status instruction 01h with
+ * two data bytes where bit 1 of the second byte is one.
+ * [...]
+ */
+#define BFPT_DWORD15_QER_MASK GENMASK(22, 20)
+#define BFPT_DWORD15_QER_NONE (0x0UL << 20) /* Micron */
+#define BFPT_DWORD15_QER_SR2_BIT1_BUGGY (0x1UL << 20)
+#define BFPT_DWORD15_QER_SR1_BIT6 (0x2UL << 20) /* Macronix */
+#define BFPT_DWORD15_QER_SR2_BIT7 (0x3UL << 20)
+#define BFPT_DWORD15_QER_SR2_BIT1_NO_RD (0x4UL << 20)
+#define BFPT_DWORD15_QER_SR2_BIT1 (0x5UL << 20) /* Spansion */
+
+struct sfdp_bfpt {
+ u32 dwords[BFPT_DWORD_MAX];
+};
+
+/* Fast Read settings. */
+
+static inline void
+spi_nor_set_read_settings_from_bfpt(struct spi_nor_read_command *read,
+ u16 half,
+ enum spi_nor_protocol proto)
+{
+ read->num_mode_clocks = (half >> 5) & 0x07;
+ read->num_wait_states = (half >> 0) & 0x1f;
+ read->opcode = (half >> 8) & 0xff;
+ read->proto = proto;
+}
+
+struct sfdp_bfpt_read {
+ /* The Fast Read x-y-z hardware capability in params->hwcaps.mask. */
+ u32 hwcaps;
+
+ /*
+ * The <supported_bit> bit in <supported_dword> BFPT DWORD tells us
+ * whether the Fast Read x-y-z command is supported.
+ */
+ u32 supported_dword;
+ u32 supported_bit;
+
+ /*
+ * The half-word at offset <setting_shift> in <setting_dword> BFPT DWORD
+ * encodes the op code, the number of mode clocks and the number of wait
+ * states to be used by Fast Read x-y-z command.
+ */
+ u32 settings_dword;
+ u32 settings_shift;
+
+ /* The SPI protocol for this Fast Read x-y-z command. */
+ enum spi_nor_protocol proto;
+};
+
+static const struct sfdp_bfpt_read sfdp_bfpt_reads[] = {
+ /* Fast Read 1-1-2 */
+ {
+ SNOR_HWCAPS_READ_1_1_2,
+ BFPT_DWORD(1), BIT(16), /* Supported bit */
+ BFPT_DWORD(4), 0, /* Settings */
+ SNOR_PROTO_1_1_2,
+ },
+
+ /* Fast Read 1-2-2 */
+ {
+ SNOR_HWCAPS_READ_1_2_2,
+ BFPT_DWORD(1), BIT(20), /* Supported bit */
+ BFPT_DWORD(4), 16, /* Settings */
+ SNOR_PROTO_1_2_2,
+ },
+
+ /* Fast Read 2-2-2 */
+ {
+ SNOR_HWCAPS_READ_2_2_2,
+ BFPT_DWORD(5), BIT(0), /* Supported bit */
+ BFPT_DWORD(6), 16, /* Settings */
+ SNOR_PROTO_2_2_2,
+ },
+
+ /* Fast Read 1-1-4 */
+ {
+ SNOR_HWCAPS_READ_1_1_4,
+ BFPT_DWORD(1), BIT(22), /* Supported bit */
+ BFPT_DWORD(3), 16, /* Settings */
+ SNOR_PROTO_1_1_4,
+ },
+
+ /* Fast Read 1-4-4 */
+ {
+ SNOR_HWCAPS_READ_1_4_4,
+ BFPT_DWORD(1), BIT(21), /* Supported bit */
+ BFPT_DWORD(3), 0, /* Settings */
+ SNOR_PROTO_1_4_4,
+ },
+
+ /* Fast Read 4-4-4 */
+ {
+ SNOR_HWCAPS_READ_4_4_4,
+ BFPT_DWORD(5), BIT(4), /* Supported bit */
+ BFPT_DWORD(7), 16, /* Settings */
+ SNOR_PROTO_4_4_4,
+ },
+};
+
+struct sfdp_bfpt_erase {
+ /*
+ * The half-word at offset <shift> in DWORD <dwoard> encodes the
+ * op code and erase sector size to be used by Sector Erase commands.
+ */
+ u32 dword;
+ u32 shift;
+};
+
+static const struct sfdp_bfpt_erase sfdp_bfpt_erases[] = {
+ /* Erase Type 1 in DWORD8 bits[15:0] */
+ {BFPT_DWORD(8), 0},
+
+ /* Erase Type 2 in DWORD8 bits[31:16] */
+ {BFPT_DWORD(8), 16},
+
+ /* Erase Type 3 in DWORD9 bits[15:0] */
+ {BFPT_DWORD(9), 0},
+
+ /* Erase Type 4 in DWORD9 bits[31:16] */
+ {BFPT_DWORD(9), 16},
+};
+
+static int spi_nor_hwcaps2cmd(u32 hwcaps, const int table[][2], size_t size)
+{
+ size_t i;
+
+ for (i = 0; i < size; i++)
+ if (table[i][0] == (int)hwcaps)
+ return table[i][1];
+
+ return -EINVAL;
+}
+
+static int spi_nor_hwcaps_read2cmd(u32 hwcaps)
+{
+ static const int hwcaps_read2cmd[][2] = {
+ { SNOR_HWCAPS_READ, SNOR_CMD_READ },
+ { SNOR_HWCAPS_READ_FAST, SNOR_CMD_READ_FAST },
+ { SNOR_HWCAPS_READ_1_1_1_DTR, SNOR_CMD_READ_1_1_1_DTR },
+ { SNOR_HWCAPS_READ_1_1_2, SNOR_CMD_READ_1_1_2 },
+ { SNOR_HWCAPS_READ_1_2_2, SNOR_CMD_READ_1_2_2 },
+ { SNOR_HWCAPS_READ_2_2_2, SNOR_CMD_READ_2_2_2 },
+ { SNOR_HWCAPS_READ_1_2_2_DTR, SNOR_CMD_READ_1_2_2_DTR },
+ { SNOR_HWCAPS_READ_1_1_4, SNOR_CMD_READ_1_1_4 },
+ { SNOR_HWCAPS_READ_1_4_4, SNOR_CMD_READ_1_4_4 },
+ { SNOR_HWCAPS_READ_4_4_4, SNOR_CMD_READ_4_4_4 },
+ { SNOR_HWCAPS_READ_1_4_4_DTR, SNOR_CMD_READ_1_4_4_DTR },
+ { SNOR_HWCAPS_READ_1_1_8, SNOR_CMD_READ_1_1_8 },
+ { SNOR_HWCAPS_READ_1_8_8, SNOR_CMD_READ_1_8_8 },
+ { SNOR_HWCAPS_READ_8_8_8, SNOR_CMD_READ_8_8_8 },
+ { SNOR_HWCAPS_READ_1_8_8_DTR, SNOR_CMD_READ_1_8_8_DTR },
+ };
+
+ return spi_nor_hwcaps2cmd(hwcaps, hwcaps_read2cmd,
+ ARRAY_SIZE(hwcaps_read2cmd));
+}
+
+/**
+ * spi_nor_parse_bfpt() - read and parse the Basic Flash Parameter Table.
+ * @nor: pointer to a 'struct spi_nor'
+ * @bfpt_header: pointer to the 'struct sfdp_parameter_header' describing
+ * the Basic Flash Parameter Table length and version
+ * @params: pointer to the 'struct spi_nor_flash_parameter' to be
+ * filled
+ *
+ * The Basic Flash Parameter Table is the main and only mandatory table as
+ * defined by the SFDP (JESD216) specification.
+ * It provides us with the total size (memory density) of the data array and
+ * the number of address bytes for Fast Read, Page Program and Sector Erase
+ * commands.
+ * For Fast READ commands, it also gives the number of mode clock cycles and
+ * wait states (regrouped in the number of dummy clock cycles) for each
+ * supported instruction op code.
+ * For Page Program, the page size is now available since JESD216 rev A, however
+ * the supported instruction op codes are still not provided.
+ * For Sector Erase commands, this table stores the supported instruction op
+ * codes and the associated sector sizes.
+ * Finally, the Quad Enable Requirements (QER) are also available since JESD216
+ * rev A. The QER bits encode the manufacturer dependent procedure to be
+ * executed to set the Quad Enable (QE) bit in some internal register of the
+ * Quad SPI memory. Indeed the QE bit, when it exists, must be set before
+ * sending any Quad SPI command to the memory. Actually, setting the QE bit
+ * tells the memory to reassign its WP# and HOLD#/RESET# pins to functions IO2
+ * and IO3 hence enabling 4 (Quad) I/O lines.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_parse_bfpt(struct spi_nor *nor,
+ const struct sfdp_parameter_header *bfpt_header,
+ struct spi_nor_flash_parameter *params)
+{
+ struct mtd_info *mtd = &nor->mtd;
+ struct sfdp_bfpt bfpt;
+ size_t len;
+ int i, cmd, err;
+ u32 addr;
+ u16 half;
+
+ /* JESD216 Basic Flash Parameter Table length is at least 9 DWORDs. */
+ if (bfpt_header->length < BFPT_DWORD_MAX_JESD216)
+ return -EINVAL;
+
+ /* Read the Basic Flash Parameter Table. */
+ len = min_t(size_t, sizeof(bfpt),
+ bfpt_header->length * sizeof(u32));
+ addr = SFDP_PARAM_HEADER_PTP(bfpt_header);
+ memset(&bfpt, 0, sizeof(bfpt));
+ err = spi_nor_read_sfdp(nor, addr, len, &bfpt);
+ if (err < 0)
+ return err;
+
+ /* Fix endianness of the BFPT DWORDs. */
+ for (i = 0; i < BFPT_DWORD_MAX; i++)
+ bfpt.dwords[i] = le32_to_cpu(bfpt.dwords[i]);
+
+ /* Number of address bytes. */
+ switch (bfpt.dwords[BFPT_DWORD(1)] & BFPT_DWORD1_ADDRESS_BYTES_MASK) {
+ case BFPT_DWORD1_ADDRESS_BYTES_3_ONLY:
+ nor->addr_width = 3;
+ break;
+
+ case BFPT_DWORD1_ADDRESS_BYTES_4_ONLY:
+ nor->addr_width = 4;
+ break;
+
+ default:
+ break;
+ }
+
+ /* Flash Memory Density (in bits). */
+ params->size = bfpt.dwords[BFPT_DWORD(2)];
+ if (params->size & BIT(31)) {
+ params->size &= ~BIT(31);
+
+ /*
+ * Prevent overflows on params->size. Anyway, a NOR of 2^64
+ * bits is unlikely to exist so this error probably means
+ * the BFPT we are reading is corrupted/wrong.
+ */
+ if (params->size > 63)
+ return -EINVAL;
+
+ params->size = 1ULL << params->size;
+ } else {
+ params->size++;
+ }
+ params->size >>= 3; /* Convert to bytes. */
+
+ /* Fast Read settings. */
+ for (i = 0; i < ARRAY_SIZE(sfdp_bfpt_reads); i++) {
+ const struct sfdp_bfpt_read *rd = &sfdp_bfpt_reads[i];
+ struct spi_nor_read_command *read;
+
+ if (!(bfpt.dwords[rd->supported_dword] & rd->supported_bit)) {
+ params->hwcaps.mask &= ~rd->hwcaps;
+ continue;
+ }
+
+ params->hwcaps.mask |= rd->hwcaps;
+ cmd = spi_nor_hwcaps_read2cmd(rd->hwcaps);
+ read = ¶ms->reads[cmd];
+ half = bfpt.dwords[rd->settings_dword] >> rd->settings_shift;
+ spi_nor_set_read_settings_from_bfpt(read, half, rd->proto);
+ }
+
+ /* Sector Erase settings. */
+ for (i = 0; i < ARRAY_SIZE(sfdp_bfpt_erases); i++) {
+ const struct sfdp_bfpt_erase *er = &sfdp_bfpt_erases[i];
+ u32 erasesize;
+ u8 opcode;
+
+ half = bfpt.dwords[er->dword] >> er->shift;
+ erasesize = half & 0xff;
+
+ /* erasesize == 0 means this Erase Type is not supported. */
+ if (!erasesize)
+ continue;
+
+ erasesize = 1U << erasesize;
+ opcode = (half >> 8) & 0xff;
+#ifdef CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
+ if (erasesize == SZ_4K) {
+ nor->erase_opcode = opcode;
+ mtd->erasesize = erasesize;
+ break;
+ }
+#endif
+ if (!mtd->erasesize || mtd->erasesize < erasesize) {
+ nor->erase_opcode = opcode;
+ mtd->erasesize = erasesize;
+ }
+ }
+
+ /* Stop here if not JESD216 rev A or later. */
+ if (bfpt_header->length < BFPT_DWORD_MAX)
+ return 0;
+
+ /* Page size: this field specifies 'N' so the page size = 2^N bytes. */
+ params->page_size = bfpt.dwords[BFPT_DWORD(11)];
+ params->page_size &= BFPT_DWORD11_PAGE_SIZE_MASK;
+ params->page_size >>= BFPT_DWORD11_PAGE_SIZE_SHIFT;
+ params->page_size = 1U << params->page_size;
+
+ /* Quad Enable Requirements. */
+ switch (bfpt.dwords[BFPT_DWORD(15)] & BFPT_DWORD15_QER_MASK) {
+ case BFPT_DWORD15_QER_NONE:
+ params->quad_enable = NULL;
+ break;
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+ case BFPT_DWORD15_QER_SR2_BIT1_BUGGY:
+ case BFPT_DWORD15_QER_SR2_BIT1_NO_RD:
+ params->quad_enable = spansion_no_read_cr_quad_enable;
+ break;
+#endif
+#ifdef CONFIG_SPI_FLASH_MACRONIX
+ case BFPT_DWORD15_QER_SR1_BIT6:
+ params->quad_enable = macronix_quad_enable;
+ break;
+#endif
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+ case BFPT_DWORD15_QER_SR2_BIT1:
+ params->quad_enable = spansion_read_cr_quad_enable;
+ break;
+#endif
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * spi_nor_parse_sfdp() - parse the Serial Flash Discoverable Parameters.
+ * @nor: pointer to a 'struct spi_nor'
+ * @params: pointer to the 'struct spi_nor_flash_parameter' to be
+ * filled
+ *
+ * The Serial Flash Discoverable Parameters are described by the JEDEC JESD216
+ * specification. This is a standard which tends to supported by almost all
+ * (Q)SPI memory manufacturers. Those hard-coded tables allow us to learn at
+ * runtime the main parameters needed to perform basic SPI flash operations such
+ * as Fast Read, Page Program or Sector Erase commands.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_parse_sfdp(struct spi_nor *nor,
+ struct spi_nor_flash_parameter *params)
+{
+ const struct sfdp_parameter_header *param_header, *bfpt_header;
+ struct sfdp_parameter_header *param_headers = NULL;
+ struct sfdp_header header;
+ size_t psize;
+ int i, err;
+
+ /* Get the SFDP header. */
+ err = spi_nor_read_sfdp(nor, 0, sizeof(header), &header);
+ if (err < 0)
+ return err;
+
+ /* Check the SFDP header version. */
+ if (le32_to_cpu(header.signature) != SFDP_SIGNATURE ||
+ header.major != SFDP_JESD216_MAJOR)
+ return -EINVAL;
+
+ /*
+ * Verify that the first and only mandatory parameter header is a
+ * Basic Flash Parameter Table header as specified in JESD216.
+ */
+ bfpt_header = &header.bfpt_header;
+ if (SFDP_PARAM_HEADER_ID(bfpt_header) != SFDP_BFPT_ID ||
+ bfpt_header->major != SFDP_JESD216_MAJOR)
+ return -EINVAL;
+
+ /*
+ * Allocate memory then read all parameter headers with a single
+ * Read SFDP command. These parameter headers will actually be parsed
+ * twice: a first time to get the latest revision of the basic flash
+ * parameter table, then a second time to handle the supported optional
+ * tables.
+ * Hence we read the parameter headers once for all to reduce the
+ * processing time. Also we use kmalloc() instead of devm_kmalloc()
+ * because we don't need to keep these parameter headers: the allocated
+ * memory is always released with kfree() before exiting this function.
+ */
+ if (header.nph) {
+ psize = header.nph * sizeof(*param_headers);
+
+ param_headers = kmalloc(psize, GFP_KERNEL);
+ if (!param_headers)
+ return -ENOMEM;
+
+ err = spi_nor_read_sfdp(nor, sizeof(header),
+ psize, param_headers);
+ if (err < 0) {
+ dev_err(dev, "failed to read SFDP parameter headers\n");
+ goto exit;
+ }
+ }
+
+ /*
+ * Check other parameter headers to get the latest revision of
+ * the basic flash parameter table.
+ */
+ for (i = 0; i < header.nph; i++) {
+ param_header = ¶m_headers[i];
+
+ if (SFDP_PARAM_HEADER_ID(param_header) == SFDP_BFPT_ID &&
+ param_header->major == SFDP_JESD216_MAJOR &&
+ (param_header->minor > bfpt_header->minor ||
+ (param_header->minor == bfpt_header->minor &&
+ param_header->length > bfpt_header->length)))
+ bfpt_header = param_header;
+ }
+
+ err = spi_nor_parse_bfpt(nor, bfpt_header, params);
+ if (err)
+ goto exit;
+
+ /* Parse other parameter headers. */
+ for (i = 0; i < header.nph; i++) {
+ param_header = ¶m_headers[i];
+
+ switch (SFDP_PARAM_HEADER_ID(param_header)) {
+ case SFDP_SECTOR_MAP_ID:
+ dev_info(dev, "non-uniform erase sector maps are not supported yet.\n");
+ break;
+
+ default:
+ break;
+ }
+
+ if (err)
+ goto exit;
+ }
+
+exit:
+ kfree(param_headers);
+ return err;
+}
+#else
+static int spi_nor_parse_sfdp(struct spi_nor *nor,
+ struct spi_nor_flash_parameter *params)
+{
+ return -EINVAL;
+}
+#endif /* SPI_FLASH_SFDP_SUPPORT */
+
+static int spi_nor_init_params(struct spi_nor *nor,
+ const struct flash_info *info,
+ struct spi_nor_flash_parameter *params)
+{
+ /* Set legacy flash parameters as default. */
+ memset(params, 0, sizeof(*params));
+
+ /* Set SPI NOR sizes. */
+ params->size = info->sector_size * info->n_sectors;
+ params->page_size = info->page_size;
+
+ /* (Fast) Read settings. */
+ params->hwcaps.mask |= SNOR_HWCAPS_READ;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ],
+ 0, 0, SPINOR_OP_READ,
+ SNOR_PROTO_1_1_1);
+
+ if (!(info->flags & SPI_NOR_NO_FR)) {
+ params->hwcaps.mask |= SNOR_HWCAPS_READ_FAST;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_FAST],
+ 0, 8, SPINOR_OP_READ_FAST,
+ SNOR_PROTO_1_1_1);
+ }
+
+ if (info->flags & SPI_NOR_DUAL_READ) {
+ params->hwcaps.mask |= SNOR_HWCAPS_READ_1_1_2;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_1_1_2],
+ 0, 8, SPINOR_OP_READ_1_1_2,
+ SNOR_PROTO_1_1_2);
+ }
+
+ if (info->flags & SPI_NOR_QUAD_READ) {
+ params->hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_1_1_4],
+ 0, 8, SPINOR_OP_READ_1_1_4,
+ SNOR_PROTO_1_1_4);
+ }
+
+ /* Page Program settings. */
+ params->hwcaps.mask |= SNOR_HWCAPS_PP;
+ spi_nor_set_pp_settings(¶ms->page_programs[SNOR_CMD_PP],
+ SPINOR_OP_PP, SNOR_PROTO_1_1_1);
+
+ if (info->flags & SPI_NOR_QUAD_READ) {
+ params->hwcaps.mask |= SNOR_HWCAPS_PP_1_1_4;
+ spi_nor_set_pp_settings(¶ms->page_programs[SNOR_CMD_PP_1_1_4],
+ SPINOR_OP_PP_1_1_4, SNOR_PROTO_1_1_4);
+ }
+
+ /* Select the procedure to set the Quad Enable bit. */
+ if (params->hwcaps.mask & (SNOR_HWCAPS_READ_QUAD |
+ SNOR_HWCAPS_PP_QUAD)) {
+ switch (JEDEC_MFR(info)) {
+#ifdef CONFIG_SPI_FLASH_MACRONIX
+ case SNOR_MFR_MACRONIX:
+ params->quad_enable = macronix_quad_enable;
+ break;
+#endif
+ case SNOR_MFR_ST:
+ case SNOR_MFR_MICRON:
+ break;
+
+ default:
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+ /* Kept only for backward compatibility purpose. */
+ params->quad_enable = spansion_read_cr_quad_enable;
+#endif
+ break;
+ }
+#ifndef __UBOOT__
+ /*
+ * Some manufacturer like GigaDevice may use different
+ * bit to set QE on different memories, so the MFR can't
+ * indicate the quad_enable method for this case, we need
+ * set it in flash info list.
+ */
+ if (info->quad_enable)
+ params->quad_enable = info->quad_enable;
+#endif
+ }
+
+ /* Override the parameters with data read from SFDP tables. */
+ nor->addr_width = 0;
+ nor->mtd.erasesize = 0;
+ if ((info->flags & (SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)) &&
+ !(info->flags & SPI_NOR_SKIP_SFDP)) {
+ struct spi_nor_flash_parameter sfdp_params;
+
+ memcpy(&sfdp_params, params, sizeof(sfdp_params));
+ if (spi_nor_parse_sfdp(nor, &sfdp_params)) {
+ nor->addr_width = 0;
+ nor->mtd.erasesize = 0;
+ } else {
+ memcpy(params, &sfdp_params, sizeof(*params));
+ }
+ }
+
+ return 0;
+}
+
+static int spi_nor_select_read(struct spi_nor *nor,
+ const struct spi_nor_flash_parameter *params,
+ u32 shared_hwcaps)
+{
+ int best_match = shared_hwcaps & SNOR_HWCAPS_READ_MASK;
+ int cmd;
+ const struct spi_nor_read_command *read;
+
+ if (best_match < 0)
+ return -EINVAL;
+
+ if (best_match & SNOR_HWCAPS_READ_1_4_4)
+ cmd = SNOR_CMD_READ_1_4_4;
+ else if (best_match & SNOR_HWCAPS_READ_1_1_4)
+ cmd = SNOR_CMD_READ_1_1_4;
+ else if (best_match & SNOR_HWCAPS_READ_FAST)
+ cmd = SNOR_CMD_READ_FAST;
+ else
+ cmd = SNOR_CMD_READ;
+
+ read = ¶ms->reads[cmd];
+ nor->read_opcode = read->opcode;
+ nor->read_proto = read->proto;
+
+ /*
+ * In the spi-nor framework, we don't need to make the difference
+ * between mode clock cycles and wait state clock cycles.
+ * Indeed, the value of the mode clock cycles is used by a QSPI
+ * flash memory to know whether it should enter or leave its 0-4-4
+ * (Continuous Read / XIP) mode.
+ * eXecution In Place is out of the scope of the mtd sub-system.
+ * Hence we choose to merge both mode and wait state clock cycles
+ * into the so called dummy clock cycles.
+ */
+ nor->read_dummy = read->num_mode_clocks + read->num_wait_states;
+ return 0;
+}
+
+static int spi_nor_select_pp(struct spi_nor *nor,
+ const struct spi_nor_flash_parameter *params,
+ u32 shared_hwcaps)
+{
+ int best_match = shared_hwcaps & SNOR_HWCAPS_PP_MASK;
+ int cmd;
+ const struct spi_nor_pp_command *pp;
+
+ if (best_match < 0)
+ return -EINVAL;
+
+ if (best_match & SNOR_HWCAPS_PP_1_1_4)
+ cmd = SNOR_CMD_PP_1_1_4;
+ else
+ cmd = SNOR_CMD_PP;
+
+ pp = ¶ms->page_programs[cmd];
+ nor->program_opcode = pp->opcode;
+ nor->write_proto = pp->proto;
+ return 0;
+}
+
+static int spi_nor_select_erase(struct spi_nor *nor,
+ const struct flash_info *info)
+{
+ struct mtd_info *mtd = &nor->mtd;
+
+ /* Do nothing if already configured from SFDP. */
+ if (mtd->erasesize)
+ return 0;
+
+#ifdef CONFIG_SPI_FLASH_USE_4K_SECTORS
+ /* prefer "small sector" erase if possible */
+ if (info->flags & SECT_4K) {
+ nor->erase_opcode = SPINOR_OP_BE_4K;
+ mtd->erasesize = 4096;
+ } else if (info->flags & SECT_4K_PMC) {
+ nor->erase_opcode = SPINOR_OP_BE_4K_PMC;
+ mtd->erasesize = 4096;
+ } else
+#endif
+ {
+ nor->erase_opcode = SPINOR_OP_SE;
+ mtd->erasesize = info->sector_size;
+ }
+ return 0;
+}
+
+static int spi_nor_setup(struct spi_nor *nor, const struct flash_info *info,
+ const struct spi_nor_flash_parameter *params,
+ const struct spi_nor_hwcaps *hwcaps)
+{
+ u32 ignored_mask, shared_mask;
+ bool enable_quad_io;
+ int err;
+
+ /*
+ * Keep only the hardware capabilities supported by both the SPI
+ * controller and the SPI flash memory.
+ */
+ shared_mask = hwcaps->mask & params->hwcaps.mask;
+
+ /* SPI n-n-n protocols are not supported yet. */
+ ignored_mask = (SNOR_HWCAPS_READ_2_2_2 |
+ SNOR_HWCAPS_READ_4_4_4 |
+ SNOR_HWCAPS_READ_8_8_8 |
+ SNOR_HWCAPS_PP_4_4_4 |
+ SNOR_HWCAPS_PP_8_8_8);
+ if (shared_mask & ignored_mask) {
+ dev_dbg(nor->dev,
+ "SPI n-n-n protocols are not supported yet.\n");
+ shared_mask &= ~ignored_mask;
+ }
+
+ /* Select the (Fast) Read command. */
+ err = spi_nor_select_read(nor, params, shared_mask);
+ if (err) {
+ dev_dbg(nor->dev,
+ "can't select read settings supported by both the SPI controller and memory.\n");
+ return err;
+ }
+
+ /* Select the Page Program command. */
+ err = spi_nor_select_pp(nor, params, shared_mask);
+ if (err) {
+ dev_dbg(nor->dev,
+ "can't select write settings supported by both the SPI controller and memory.\n");
+ return err;
+ }
+
+ /* Select the Sector Erase command. */
+ err = spi_nor_select_erase(nor, info);
+ if (err) {
+ dev_dbg(nor->dev,
+ "can't select erase settings supported by both the SPI controller and memory.\n");
+ return err;
+ }
+
+ /* Enable Quad I/O if needed. */
+ enable_quad_io = (spi_nor_get_protocol_width(nor->read_proto) == 4 ||
+ spi_nor_get_protocol_width(nor->write_proto) == 4);
+ if (enable_quad_io && params->quad_enable)
+ nor->quad_enable = params->quad_enable;
+ else
+ nor->quad_enable = NULL;
+
+ return 0;
+}
+
+static int spi_nor_init(struct spi_nor *nor)
+{
+ int err;
+
+ /*
+ * Atmel, SST, Intel/Numonyx, and others serial NOR tend to power up
+ * with the software protection bits set
+ */
+ if (JEDEC_MFR(nor->info) == SNOR_MFR_ATMEL ||
+ JEDEC_MFR(nor->info) == SNOR_MFR_INTEL ||
+ JEDEC_MFR(nor->info) == SNOR_MFR_SST ||
+ nor->info->flags & SPI_NOR_HAS_LOCK) {
+ write_enable(nor);
+ write_sr(nor, 0);
+ spi_nor_wait_till_ready(nor);
+ }
+
+ if (nor->quad_enable) {
+ err = nor->quad_enable(nor);
+ if (err) {
+ dev_dbg(nor->dev, "quad mode not supported\n");
+ return err;
+ }
+ }
+
+ if (nor->addr_width == 4 &&
+ (JEDEC_MFR(nor->info) != SNOR_MFR_SPANSION) &&
+ !(nor->info->flags & SPI_NOR_4B_OPCODES)) {
+ /*
+ * If the RESET# pin isn't hooked up properly, or the system
+ * otherwise doesn't perform a reset command in the boot
+ * sequence, it's impossible to 100% protect against unexpected
+ * reboots (e.g., crashes). Warn the user (or hopefully, system
+ * designer) that this is bad.
+ */
+ if (nor->flags & SNOR_F_BROKEN_RESET)
+ printf("enabling reset hack; may not recover from unexpected reboots\n");
+ set_4byte(nor, nor->info, 1);
+ }
+
+ return 0;
+}
+
+int spi_nor_scan(struct spi_nor *nor)
+{
+ struct spi_nor_flash_parameter params;
+ const struct flash_info *info = NULL;
+ struct mtd_info *mtd = &nor->mtd;
+ struct spi_nor_hwcaps hwcaps = {
+ .mask = SNOR_HWCAPS_READ |
+ SNOR_HWCAPS_READ_FAST |
+ SNOR_HWCAPS_PP,
+ };
+ struct spi_slave *spi = nor->spi;
+ int ret;
+
+ /* Reset SPI protocol for all commands. */
+ nor->reg_proto = SNOR_PROTO_1_1_1;
+ nor->read_proto = SNOR_PROTO_1_1_1;
+ nor->write_proto = SNOR_PROTO_1_1_1;
+ nor->read = spi_nor_read_data;
+ nor->write = spi_nor_write_data;
+ nor->read_reg = spi_nor_read_reg;
+ nor->write_reg = spi_nor_write_reg;
+
+ if (spi->mode & SPI_RX_QUAD) {
+ hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4;
+
+ if (spi->mode & SPI_TX_QUAD)
+ hwcaps.mask |= (SNOR_HWCAPS_READ_1_4_4 |
+ SNOR_HWCAPS_PP_1_1_4 |
+ SNOR_HWCAPS_PP_1_4_4);
+ } else if (spi->mode & SPI_RX_DUAL) {
+ hwcaps.mask |= SNOR_HWCAPS_READ_1_1_2;
+
+ if (spi->mode & SPI_TX_DUAL)
+ hwcaps.mask |= SNOR_HWCAPS_READ_1_2_2;
+ }
+
+ info = spi_nor_read_id(nor);
+ if (IS_ERR_OR_NULL(info))
+ return -ENOENT;
+ /* Parse the Serial Flash Discoverable Parameters table. */
+ ret = spi_nor_init_params(nor, info, ¶ms);
+ if (ret)
+ return ret;
+
+ if (!mtd->name)
+ mtd->name = info->name;
+ mtd->priv = nor;
+ mtd->type = MTD_NORFLASH;
+ mtd->writesize = 1;
+ mtd->flags = MTD_CAP_NORFLASH;
+ mtd->size = params.size;
+ mtd->_erase = spi_nor_erase;
+ mtd->_read = spi_nor_read;
+
+#if defined(CONFIG_SPI_FLASH_STMICRO) || defined(CONFIG_SPI_FLASH_SST)
+ /* NOR protection support for STmicro/Micron chips and similar */
+ if (JEDEC_MFR(info) == SNOR_MFR_ST ||
+ JEDEC_MFR(info) == SNOR_MFR_MICRON ||
+ JEDEC_MFR(info) == SNOR_MFR_SST ||
+ info->flags & SPI_NOR_HAS_LOCK) {
+ nor->flash_lock = stm_lock;
+ nor->flash_unlock = stm_unlock;
+ nor->flash_is_locked = stm_is_locked;
+ }
+#endif
+
+ if (nor->flash_lock && nor->flash_unlock && nor->flash_is_locked) {
+ mtd->_lock = spi_nor_lock;
+ mtd->_unlock = spi_nor_unlock;
+ mtd->_is_locked = spi_nor_is_locked;
+ }
+
+#ifdef CONFIG_SPI_FLASH_SST
+ /* sst nor chips use AAI word program */
+ if (info->flags & SST_WRITE)
+ mtd->_write = sst_write;
+ else
+#endif
+ mtd->_write = spi_nor_write;
+
+ if (info->flags & USE_FSR)
+ nor->flags |= SNOR_F_USE_FSR;
+ if (info->flags & SPI_NOR_HAS_TB)
+ nor->flags |= SNOR_F_HAS_SR_TB;
+ if (info->flags & NO_CHIP_ERASE)
+ nor->flags |= SNOR_F_NO_OP_CHIP_ERASE;
+ if (info->flags & USE_CLSR)
+ nor->flags |= SNOR_F_USE_CLSR;
+
+ if (info->flags & SPI_NOR_NO_ERASE)
+ mtd->flags |= MTD_NO_ERASE;
+
+ nor->page_size = params.page_size;
+ mtd->writebufsize = nor->page_size;
+
+ /* Some devices cannot do fast-read, no matter what DT tells us */
+ if (info->flags & SPI_NOR_NO_FR)
+ params.hwcaps.mask &= ~SNOR_HWCAPS_READ_FAST;
+
+ /*
+ * Configure the SPI memory:
+ * - select op codes for (Fast) Read, Page Program and Sector Erase.
+ * - set the number of dummy cycles (mode cycles + wait states).
+ * - set the SPI protocols for register and memory accesses.
+ * - set the Quad Enable bit if needed (required by SPI x-y-4 protos).
+ */
+ ret = spi_nor_setup(nor, info, ¶ms, &hwcaps);
+ if (ret)
+ return ret;
+
+ if (nor->addr_width) {
+ /* already configured from SFDP */
+ } else if (info->addr_width) {
+ nor->addr_width = info->addr_width;
+ } else if (mtd->size > 0x1000000) {
+ /* enable 4-byte addressing if the device exceeds 16MiB */
+ nor->addr_width = 4;
+ if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
+ info->flags & SPI_NOR_4B_OPCODES)
+ spi_nor_set_4byte_opcodes(nor, info);
+ } else {
+ nor->addr_width = 3;
+ }
+
+ if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) {
+ dev_dbg(dev, "address width is too large: %u\n",
+ nor->addr_width);
+ return -EINVAL;
+ }
+
+ /* Send all the required SPI flash commands to initialize device */
+ nor->info = info;
+ ret = spi_nor_init(nor);
+ if (ret)
+ return ret;
+
+ nor->name = mtd->name;
+ nor->size = mtd->size;
+ nor->erase_size = mtd->erasesize;
+ nor->sector_size = mtd->erasesize;
+
+#ifndef CONFIG_SPL_BUILD
+ printf("SF: Detected %s with page size ", nor->name);
+ print_size(nor->page_size, ", erase size ");
+ print_size(nor->erase_size, ", total ");
+ print_size(nor->size, "");
+ puts("\n");
+#endif
+
+#ifndef __UBOOT__
+ dev_info(dev, "%s (%lld Kbytes)\n", info->name,
+ (long long)mtd->size >> 10);
+
+ dev_dbg(dev,
+ "mtd .name = %s, .size = 0x%llx (%lldMiB), "
+ ".erasesize = 0x%.8x (%uKiB) .numeraseregions = %d\n",
+ mtd->name, (long long)mtd->size, (long long)(mtd->size >> 20),
+ mtd->erasesize, mtd->erasesize / 1024, mtd->numeraseregions);
+
+ if (mtd->numeraseregions)
+ for (i = 0; i < mtd->numeraseregions; i++)
+ dev_dbg(dev,
+ "mtd.eraseregions[%d] = { .offset = 0x%llx, "
+ ".erasesize = 0x%.8x (%uKiB), "
+ ".numblocks = %d }\n",
+ i, (long long)mtd->eraseregions[i].offset,
+ mtd->eraseregions[i].erasesize,
+ mtd->eraseregions[i].erasesize / 1024,
+ mtd->eraseregions[i].numblocks);
+#endif
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(spi_nor_scan);
+
+/* U-Boot specific functions, need to extend MTD to support these */
+int spi_flash_cmd_get_sw_write_prot(struct spi_nor *nor)
+{
+ int sr = read_sr(nor);
+
+ if (sr < 0)
+ return sr;
+
+ return (sr >> 2) & 7;
+}
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Huang Shijie <shijie8 at gmail.com>");
+MODULE_AUTHOR("Mike Lavender");
+MODULE_DESCRIPTION("framework for SPI NOR");
diff --git a/include/linux/mtd/cfi.h b/include/linux/mtd/cfi.h
new file mode 100644
index 000000000000..3555518bd3f1
--- /dev/null
+++ b/include/linux/mtd/cfi.h
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright © 2000-2010 David Woodhouse <dwmw2 at infradead.org> et al.
+ *
+ */
+
+#ifndef __MTD_CFI_H__
+#define __MTD_CFI_H__
+
+#define CFI_MFR_ANY 0xFFFF
+#define CFI_ID_ANY 0xFFFF
+#define CFI_MFR_CONTINUATION 0x007F
+
+#define CFI_MFR_AMD 0x0001
+#define CFI_MFR_AMIC 0x0037
+#define CFI_MFR_ATMEL 0x001F
+#define CFI_MFR_EON 0x001C
+#define CFI_MFR_FUJITSU 0x0004
+#define CFI_MFR_HYUNDAI 0x00AD
+#define CFI_MFR_INTEL 0x0089
+#define CFI_MFR_MACRONIX 0x00C2
+#define CFI_MFR_NEC 0x0010
+#define CFI_MFR_PMC 0x009D
+#define CFI_MFR_SAMSUNG 0x00EC
+#define CFI_MFR_SHARP 0x00B0
+#define CFI_MFR_SST 0x00BF
+#define CFI_MFR_ST 0x0020 /* STMicroelectronics */
+#define CFI_MFR_MICRON 0x002C /* Micron */
+#define CFI_MFR_TOSHIBA 0x0098
+#define CFI_MFR_WINBOND 0x00DA
+
+#endif /* __MTD_CFI_H__ */
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
new file mode 100644
index 000000000000..2cc86b16030c
--- /dev/null
+++ b/include/linux/mtd/spi-nor.h
@@ -0,0 +1,421 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2014 Freescale Semiconductor, Inc.
+ * Synced from Linux v4.19
+ */
+
+#ifndef __LINUX_MTD_SPI_NOR_H
+#define __LINUX_MTD_SPI_NOR_H
+
+#include <linux/bitops.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/mtd.h>
+
+/*
+ * Manufacturer IDs
+ *
+ * The first byte returned from the flash after sending opcode SPINOR_OP_RDID.
+ * Sometimes these are the same as CFI IDs, but sometimes they aren't.
+ */
+#define SNOR_MFR_ATMEL CFI_MFR_ATMEL
+#define SNOR_MFR_GIGADEVICE 0xc8
+#define SNOR_MFR_INTEL CFI_MFR_INTEL
+#define SNOR_MFR_ST CFI_MFR_ST /* ST Micro <--> Micron */
+#define SNOR_MFR_MICRON CFI_MFR_MICRON /* ST Micro <--> Micron */
+#define SNOR_MFR_MACRONIX CFI_MFR_MACRONIX
+#define SNOR_MFR_SPANSION CFI_MFR_AMD
+#define SNOR_MFR_SST CFI_MFR_SST
+#define SNOR_MFR_WINBOND 0xef /* Also used by some Spansion */
+
+/*
+ * Note on opcode nomenclature: some opcodes have a format like
+ * SPINOR_OP_FUNCTION{4,}_x_y_z. The numbers x, y, and z stand for the number
+ * of I/O lines used for the opcode, address, and data (respectively). The
+ * FUNCTION has an optional suffix of '4', to represent an opcode which
+ * requires a 4-byte (32-bit) address.
+ */
+
+/* Flash opcodes. */
+#define SPINOR_OP_WREN 0x06 /* Write enable */
+#define SPINOR_OP_RDSR 0x05 /* Read status register */
+#define SPINOR_OP_WRSR 0x01 /* Write status register 1 byte */
+#define SPINOR_OP_RDSR2 0x3f /* Read status register 2 */
+#define SPINOR_OP_WRSR2 0x3e /* Write status register 2 */
+#define SPINOR_OP_READ 0x03 /* Read data bytes (low frequency) */
+#define SPINOR_OP_READ_FAST 0x0b /* Read data bytes (high frequency) */
+#define SPINOR_OP_READ_1_1_2 0x3b /* Read data bytes (Dual Output SPI) */
+#define SPINOR_OP_READ_1_2_2 0xbb /* Read data bytes (Dual I/O SPI) */
+#define SPINOR_OP_READ_1_1_4 0x6b /* Read data bytes (Quad Output SPI) */
+#define SPINOR_OP_READ_1_4_4 0xeb /* Read data bytes (Quad I/O SPI) */
+#define SPINOR_OP_PP 0x02 /* Page program (up to 256 bytes) */
+#define SPINOR_OP_PP_1_1_4 0x32 /* Quad page program */
+#define SPINOR_OP_PP_1_4_4 0x38 /* Quad page program */
+#define SPINOR_OP_BE_4K 0x20 /* Erase 4KiB block */
+#define SPINOR_OP_BE_4K_PMC 0xd7 /* Erase 4KiB block on PMC chips */
+#define SPINOR_OP_BE_32K 0x52 /* Erase 32KiB block */
+#define SPINOR_OP_CHIP_ERASE 0xc7 /* Erase whole flash chip */
+#define SPINOR_OP_SE 0xd8 /* Sector erase (usually 64KiB) */
+#define SPINOR_OP_RDID 0x9f /* Read JEDEC ID */
+#define SPINOR_OP_RDSFDP 0x5a /* Read SFDP */
+#define SPINOR_OP_RDCR 0x35 /* Read configuration register */
+#define SPINOR_OP_RDFSR 0x70 /* Read flag status register */
+#define SPINOR_OP_CLFSR 0x50 /* Clear flag status register */
+#define SPINOR_OP_RDEAR 0xc8 /* Read Extended Address Register */
+#define SPINOR_OP_WREAR 0xc5 /* Write Extended Address Register */
+
+/* 4-byte address opcodes - used on Spansion and some Macronix flashes. */
+#define SPINOR_OP_READ_4B 0x13 /* Read data bytes (low frequency) */
+#define SPINOR_OP_READ_FAST_4B 0x0c /* Read data bytes (high frequency) */
+#define SPINOR_OP_READ_1_1_2_4B 0x3c /* Read data bytes (Dual Output SPI) */
+#define SPINOR_OP_READ_1_2_2_4B 0xbc /* Read data bytes (Dual I/O SPI) */
+#define SPINOR_OP_READ_1_1_4_4B 0x6c /* Read data bytes (Quad Output SPI) */
+#define SPINOR_OP_READ_1_4_4_4B 0xec /* Read data bytes (Quad I/O SPI) */
+#define SPINOR_OP_PP_4B 0x12 /* Page program (up to 256 bytes) */
+#define SPINOR_OP_PP_1_1_4_4B 0x34 /* Quad page program */
+#define SPINOR_OP_PP_1_4_4_4B 0x3e /* Quad page program */
+#define SPINOR_OP_BE_4K_4B 0x21 /* Erase 4KiB block */
+#define SPINOR_OP_BE_32K_4B 0x5c /* Erase 32KiB block */
+#define SPINOR_OP_SE_4B 0xdc /* Sector erase (usually 64KiB) */
+
+/* Double Transfer Rate opcodes - defined in JEDEC JESD216B. */
+#define SPINOR_OP_READ_1_1_1_DTR 0x0d
+#define SPINOR_OP_READ_1_2_2_DTR 0xbd
+#define SPINOR_OP_READ_1_4_4_DTR 0xed
+
+#define SPINOR_OP_READ_1_1_1_DTR_4B 0x0e
+#define SPINOR_OP_READ_1_2_2_DTR_4B 0xbe
+#define SPINOR_OP_READ_1_4_4_DTR_4B 0xee
+
+/* Used for SST flashes only. */
+#define SPINOR_OP_BP 0x02 /* Byte program */
+#define SPINOR_OP_WRDI 0x04 /* Write disable */
+#define SPINOR_OP_AAI_WP 0xad /* Auto address increment word program */
+
+/* Used for S3AN flashes only */
+#define SPINOR_OP_XSE 0x50 /* Sector erase */
+#define SPINOR_OP_XPP 0x82 /* Page program */
+#define SPINOR_OP_XRDSR 0xd7 /* Read status register */
+
+#define XSR_PAGESIZE BIT(0) /* Page size in Po2 or Linear */
+#define XSR_RDY BIT(7) /* Ready */
+
+/* Used for Macronix and Winbond flashes. */
+#define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */
+#define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */
+
+/* Used for Spansion flashes only. */
+#define SPINOR_OP_BRWR 0x17 /* Bank register write */
+#define SPINOR_OP_CLSR 0x30 /* Clear status register 1 */
+
+/* Used for Micron flashes only. */
+#define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */
+#define SPINOR_OP_WD_EVCR 0x61 /* Write EVCR register */
+
+/* Status Register bits. */
+#define SR_WIP BIT(0) /* Write in progress */
+#define SR_WEL BIT(1) /* Write enable latch */
+/* meaning of other SR_* bits may differ between vendors */
+#define SR_BP0 BIT(2) /* Block protect 0 */
+#define SR_BP1 BIT(3) /* Block protect 1 */
+#define SR_BP2 BIT(4) /* Block protect 2 */
+#define SR_TB BIT(5) /* Top/Bottom protect */
+#define SR_SRWD BIT(7) /* SR write protect */
+/* Spansion/Cypress specific status bits */
+#define SR_E_ERR BIT(5)
+#define SR_P_ERR BIT(6)
+
+#define SR_QUAD_EN_MX BIT(6) /* Macronix Quad I/O */
+
+/* Enhanced Volatile Configuration Register bits */
+#define EVCR_QUAD_EN_MICRON BIT(7) /* Micron Quad I/O */
+
+/* Flag Status Register bits */
+#define FSR_READY BIT(7) /* Device status, 0 = Busy, 1 = Ready */
+#define FSR_E_ERR BIT(5) /* Erase operation status */
+#define FSR_P_ERR BIT(4) /* Program operation status */
+#define FSR_PT_ERR BIT(1) /* Protection error bit */
+
+/* Configuration Register bits. */
+#define CR_QUAD_EN_SPAN BIT(1) /* Spansion Quad I/O */
+
+/* Status Register 2 bits. */
+#define SR2_QUAD_EN_BIT7 BIT(7)
+
+/* Supported SPI protocols */
+#define SNOR_PROTO_INST_MASK GENMASK(23, 16)
+#define SNOR_PROTO_INST_SHIFT 16
+#define SNOR_PROTO_INST(_nbits) \
+ ((((unsigned long)(_nbits)) << SNOR_PROTO_INST_SHIFT) & \
+ SNOR_PROTO_INST_MASK)
+
+#define SNOR_PROTO_ADDR_MASK GENMASK(15, 8)
+#define SNOR_PROTO_ADDR_SHIFT 8
+#define SNOR_PROTO_ADDR(_nbits) \
+ ((((unsigned long)(_nbits)) << SNOR_PROTO_ADDR_SHIFT) & \
+ SNOR_PROTO_ADDR_MASK)
+
+#define SNOR_PROTO_DATA_MASK GENMASK(7, 0)
+#define SNOR_PROTO_DATA_SHIFT 0
+#define SNOR_PROTO_DATA(_nbits) \
+ ((((unsigned long)(_nbits)) << SNOR_PROTO_DATA_SHIFT) & \
+ SNOR_PROTO_DATA_MASK)
+
+#define SNOR_PROTO_IS_DTR BIT(24) /* Double Transfer Rate */
+
+#define SNOR_PROTO_STR(_inst_nbits, _addr_nbits, _data_nbits) \
+ (SNOR_PROTO_INST(_inst_nbits) | \
+ SNOR_PROTO_ADDR(_addr_nbits) | \
+ SNOR_PROTO_DATA(_data_nbits))
+#define SNOR_PROTO_DTR(_inst_nbits, _addr_nbits, _data_nbits) \
+ (SNOR_PROTO_IS_DTR | \
+ SNOR_PROTO_STR(_inst_nbits, _addr_nbits, _data_nbits))
+
+enum spi_nor_protocol {
+ SNOR_PROTO_1_1_1 = SNOR_PROTO_STR(1, 1, 1),
+ SNOR_PROTO_1_1_2 = SNOR_PROTO_STR(1, 1, 2),
+ SNOR_PROTO_1_1_4 = SNOR_PROTO_STR(1, 1, 4),
+ SNOR_PROTO_1_1_8 = SNOR_PROTO_STR(1, 1, 8),
+ SNOR_PROTO_1_2_2 = SNOR_PROTO_STR(1, 2, 2),
+ SNOR_PROTO_1_4_4 = SNOR_PROTO_STR(1, 4, 4),
+ SNOR_PROTO_1_8_8 = SNOR_PROTO_STR(1, 8, 8),
+ SNOR_PROTO_2_2_2 = SNOR_PROTO_STR(2, 2, 2),
+ SNOR_PROTO_4_4_4 = SNOR_PROTO_STR(4, 4, 4),
+ SNOR_PROTO_8_8_8 = SNOR_PROTO_STR(8, 8, 8),
+
+ SNOR_PROTO_1_1_1_DTR = SNOR_PROTO_DTR(1, 1, 1),
+ SNOR_PROTO_1_2_2_DTR = SNOR_PROTO_DTR(1, 2, 2),
+ SNOR_PROTO_1_4_4_DTR = SNOR_PROTO_DTR(1, 4, 4),
+ SNOR_PROTO_1_8_8_DTR = SNOR_PROTO_DTR(1, 8, 8),
+};
+
+static inline bool spi_nor_protocol_is_dtr(enum spi_nor_protocol proto)
+{
+ return !!(proto & SNOR_PROTO_IS_DTR);
+}
+
+static inline u8 spi_nor_get_protocol_inst_nbits(enum spi_nor_protocol proto)
+{
+ return ((unsigned long)(proto & SNOR_PROTO_INST_MASK)) >>
+ SNOR_PROTO_INST_SHIFT;
+}
+
+static inline u8 spi_nor_get_protocol_addr_nbits(enum spi_nor_protocol proto)
+{
+ return ((unsigned long)(proto & SNOR_PROTO_ADDR_MASK)) >>
+ SNOR_PROTO_ADDR_SHIFT;
+}
+
+static inline u8 spi_nor_get_protocol_data_nbits(enum spi_nor_protocol proto)
+{
+ return ((unsigned long)(proto & SNOR_PROTO_DATA_MASK)) >>
+ SNOR_PROTO_DATA_SHIFT;
+}
+
+static inline u8 spi_nor_get_protocol_width(enum spi_nor_protocol proto)
+{
+ return spi_nor_get_protocol_data_nbits(proto);
+}
+
+#define SPI_NOR_MAX_CMD_SIZE 8
+enum spi_nor_ops {
+ SPI_NOR_OPS_READ = 0,
+ SPI_NOR_OPS_WRITE,
+ SPI_NOR_OPS_ERASE,
+ SPI_NOR_OPS_LOCK,
+ SPI_NOR_OPS_UNLOCK,
+};
+
+enum spi_nor_option_flags {
+ SNOR_F_USE_FSR = BIT(0),
+ SNOR_F_HAS_SR_TB = BIT(1),
+ SNOR_F_NO_OP_CHIP_ERASE = BIT(2),
+ SNOR_F_S3AN_ADDR_DEFAULT = BIT(3),
+ SNOR_F_READY_XSR_RDY = BIT(4),
+ SNOR_F_USE_CLSR = BIT(5),
+ SNOR_F_BROKEN_RESET = BIT(6),
+};
+
+/**
+ * struct flash_info - Forward declaration of a structure used internally by
+ * spi_nor_scan()
+ */
+struct flash_info;
+
+/* TODO: Remove, once all users of spi_flash interface are moved to MTD */
+#define spi_flash spi_nor
+
+/**
+ * struct spi_nor - Structure for defining a the SPI NOR layer
+ * @mtd: point to a mtd_info structure
+ * @lock: the lock for the read/write/erase/lock/unlock operations
+ * @dev: point to a spi device, or a spi nor controller device.
+ * @info: spi-nor part JDEC MFR id and other info
+ * @page_size: the page size of the SPI NOR
+ * @addr_width: number of address bytes
+ * @erase_opcode: the opcode for erasing a sector
+ * @read_opcode: the read opcode
+ * @read_dummy: the dummy needed by the read operation
+ * @program_opcode: the program opcode
+ * @sst_write_second: used by the SST write operation
+ * @flags: flag options for the current SPI-NOR (SNOR_F_*)
+ * @read_proto: the SPI protocol for read operations
+ * @write_proto: the SPI protocol for write operations
+ * @reg_proto the SPI protocol for read_reg/write_reg/erase operations
+ * @cmd_buf: used by the write_reg
+ * @prepare: [OPTIONAL] do some preparations for the
+ * read/write/erase/lock/unlock operations
+ * @unprepare: [OPTIONAL] do some post work after the
+ * read/write/erase/lock/unlock operations
+ * @read_reg: [DRIVER-SPECIFIC] read out the register
+ * @write_reg: [DRIVER-SPECIFIC] write data to the register
+ * @read: [DRIVER-SPECIFIC] read data from the SPI NOR
+ * @write: [DRIVER-SPECIFIC] write data to the SPI NOR
+ * @erase: [DRIVER-SPECIFIC] erase a sector of the SPI NOR
+ * at the offset @offs; if not provided by the driver,
+ * spi-nor will send the erase opcode via write_reg()
+ * @flash_lock: [FLASH-SPECIFIC] lock a region of the SPI NOR
+ * @flash_unlock: [FLASH-SPECIFIC] unlock a region of the SPI NOR
+ * @flash_is_locked: [FLASH-SPECIFIC] check if a region of the SPI NOR is
+ * @quad_enable: [FLASH-SPECIFIC] enables SPI NOR quad mode
+ * completely locked
+ * @priv: the private data
+ */
+struct spi_nor {
+ struct mtd_info mtd;
+#ifndef __UBOOT__
+ struct mutex lock;
+ struct device *dev;
+#else
+ struct udevice *dev;
+ struct spi_slave *spi;
+#endif
+ const struct flash_info *info;
+ u32 page_size;
+ u8 addr_width;
+ u8 erase_opcode;
+ u8 read_opcode;
+ u8 read_dummy;
+ u8 program_opcode;
+ enum spi_nor_protocol read_proto;
+ enum spi_nor_protocol write_proto;
+ enum spi_nor_protocol reg_proto;
+ bool sst_write_second;
+ u32 flags;
+ u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE];
+
+ int (*prepare)(struct spi_nor *nor, enum spi_nor_ops ops);
+ void (*unprepare)(struct spi_nor *nor, enum spi_nor_ops ops);
+ int (*read_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len);
+ int (*write_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len);
+
+ ssize_t (*read)(struct spi_nor *nor, loff_t from,
+ size_t len, u_char *read_buf);
+ ssize_t (*write)(struct spi_nor *nor, loff_t to,
+ size_t len, const u_char *write_buf);
+ int (*erase)(struct spi_nor *nor, loff_t offs);
+
+ int (*flash_lock)(struct spi_nor *nor, loff_t ofs, uint64_t len);
+ int (*flash_unlock)(struct spi_nor *nor, loff_t ofs, uint64_t len);
+ int (*flash_is_locked)(struct spi_nor *nor, loff_t ofs, uint64_t len);
+ int (*quad_enable)(struct spi_nor *nor);
+
+ void *priv;
+/* Compatibility for spi_flash, remove once sf layer is merged with mtd */
+ const char *name;
+ u32 size;
+ u32 sector_size;
+ u32 erase_size;
+};
+
+static inline void spi_nor_set_flash_node(struct spi_nor *nor,
+ const struct device_node *np)
+{
+ mtd_set_of_node(&nor->mtd, np);
+}
+
+static inline const struct
+device_node *spi_nor_get_flash_node(struct spi_nor *nor)
+{
+ return mtd_get_of_node(&nor->mtd);
+}
+
+/**
+ * struct spi_nor_hwcaps - Structure for describing the hardware capabilies
+ * supported by the SPI controller (bus master).
+ * @mask: the bitmask listing all the supported hw capabilies
+ */
+struct spi_nor_hwcaps {
+ u32 mask;
+};
+
+/*
+ *(Fast) Read capabilities.
+ * MUST be ordered by priority: the higher bit position, the higher priority.
+ * As a matter of performances, it is relevant to use Octo SPI protocols first,
+ * then Quad SPI protocols before Dual SPI protocols, Fast Read and lastly
+ * (Slow) Read.
+ */
+#define SNOR_HWCAPS_READ_MASK GENMASK(14, 0)
+#define SNOR_HWCAPS_READ BIT(0)
+#define SNOR_HWCAPS_READ_FAST BIT(1)
+#define SNOR_HWCAPS_READ_1_1_1_DTR BIT(2)
+
+#define SNOR_HWCAPS_READ_DUAL GENMASK(6, 3)
+#define SNOR_HWCAPS_READ_1_1_2 BIT(3)
+#define SNOR_HWCAPS_READ_1_2_2 BIT(4)
+#define SNOR_HWCAPS_READ_2_2_2 BIT(5)
+#define SNOR_HWCAPS_READ_1_2_2_DTR BIT(6)
+
+#define SNOR_HWCAPS_READ_QUAD GENMASK(10, 7)
+#define SNOR_HWCAPS_READ_1_1_4 BIT(7)
+#define SNOR_HWCAPS_READ_1_4_4 BIT(8)
+#define SNOR_HWCAPS_READ_4_4_4 BIT(9)
+#define SNOR_HWCAPS_READ_1_4_4_DTR BIT(10)
+
+#define SNOR_HWCPAS_READ_OCTO GENMASK(14, 11)
+#define SNOR_HWCAPS_READ_1_1_8 BIT(11)
+#define SNOR_HWCAPS_READ_1_8_8 BIT(12)
+#define SNOR_HWCAPS_READ_8_8_8 BIT(13)
+#define SNOR_HWCAPS_READ_1_8_8_DTR BIT(14)
+
+/*
+ * Page Program capabilities.
+ * MUST be ordered by priority: the higher bit position, the higher priority.
+ * Like (Fast) Read capabilities, Octo/Quad SPI protocols are preferred to the
+ * legacy SPI 1-1-1 protocol.
+ * Note that Dual Page Programs are not supported because there is no existing
+ * JEDEC/SFDP standard to define them. Also at this moment no SPI flash memory
+ * implements such commands.
+ */
+#define SNOR_HWCAPS_PP_MASK GENMASK(22, 16)
+#define SNOR_HWCAPS_PP BIT(16)
+
+#define SNOR_HWCAPS_PP_QUAD GENMASK(19, 17)
+#define SNOR_HWCAPS_PP_1_1_4 BIT(17)
+#define SNOR_HWCAPS_PP_1_4_4 BIT(18)
+#define SNOR_HWCAPS_PP_4_4_4 BIT(19)
+
+#define SNOR_HWCAPS_PP_OCTO GENMASK(22, 20)
+#define SNOR_HWCAPS_PP_1_1_8 BIT(20)
+#define SNOR_HWCAPS_PP_1_8_8 BIT(21)
+#define SNOR_HWCAPS_PP_8_8_8 BIT(22)
+
+/**
+ * spi_nor_scan() - scan the SPI NOR
+ * @nor: the spi_nor structure
+ *
+ * The drivers can use this function to scan the SPI NOR.
+ * In the scanning, it will try to get all the necessary information to
+ * fill the mtd_info{} and the spi_nor{}.
+ *
+ * Return: 0 for success, others for failure.
+ */
+int spi_nor_scan(struct spi_nor *nor);
+
+/**
+ * spi_nor_restore_addr_mode() - restore the status of SPI NOR
+ * @nor: the spi_nor structure
+ */
+void spi_nor_restore(struct spi_nor *nor);
+
+#endif
--
2.19.2
More information about the U-Boot
mailing list