[U-Boot] [PATCH] imx6q_logic: Enable MMC booting from SPL

[Adam Ford]

The MMC booting wasn't previously fitting into the codespace.
This patch enables MMC booting from the baseboard by reducing
some DM overhead during SPL.

Signed-off-by: Adam Ford <aford173 at gmail.com>

diff --git a/board/logicpd/imx6/imx6logic.c b/board/logicpd/imx6/imx6logic.c
index ce1c8a5d6b..696f5c4183 100644
--- a/board/logicpd/imx6/imx6logic.c
+++ b/board/logicpd/imx6/imx6logic.c
@@ -60,6 +60,7 @@ static iomux_v3_cfg_t const uart3_pads[] = {
 	MX6_PAD_EIM_EB3__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
 };
 
+#ifndef CONFIG_SPL_BUILD
 static void fixup_enet_clock(void)
 {
 	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
@@ -108,6 +109,7 @@ static void fixup_enet_clock(void)
 	dm_gpio_set_value(&reset, 1);
 	mdelay(50);
 }
+#endif
 
 static void setup_iomux_uart(void)
 {
@@ -158,7 +160,9 @@ int overwrite_console(void)
 
 int board_early_init_f(void)
 {
+#ifndef CONFIG_SPL_BUILD
 	fixup_enet_clock();
+#endif
 	setup_iomux_uart();
 	setup_nand_pins();
 	return 0;
@@ -200,6 +204,74 @@ int spl_start_uboot(void)
 }
 #endif
 
+/* SD interface */
+#define USDHC_PAD_CTRL							\
+	(PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |	\
+	 PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	MX6_PAD_SD1_CLK__SD1_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_CMD__SD1_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_SD2_DAT0__SD2_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT1__SD2_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT2__SD2_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT3__SD2_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_GPIO_4__GPIO1_IO04	| MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{USDHC1_BASE_ADDR}, /* SOM */
+	{USDHC2_BASE_ADDR}  /* Baseboard */
+};
+
+int board_mmc_init(bd_t *bis)
+{
+	struct src *psrc = (struct src *)SRC_BASE_ADDR;
+	unsigned int reg = readl(&psrc->sbmr1) >> 11;
+	/*
+	 * Upon reading BOOT_CFG register the following map is done:
+	 * Bit 11 and 12 of BOOT_CFG register can determine the current
+	 * mmc port
+	 * 0x1                  SD1-SOM
+	 * 0x2                  SD2-Baseboard
+	 */
+
+	reg &= 0x3; /* Only care about bottom 2 bits */
+
+	switch (reg - 1) {
+	case 0:
+		SETUP_IOMUX_PADS(usdhc1_pads);
+		usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR;
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+		break;
+	case 1:
+		SETUP_IOMUX_PADS(usdhc2_pads);
+		usdhc_cfg[1].esdhc_base = USDHC2_BASE_ADDR;
+		usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+		gd->arch.sdhc_clk = usdhc_cfg[1].sdhc_clk;
+		break;
+	}
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[reg - 1]);
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	return 1;
+}
+#endif
+
 static void ccgr_init(void)
 {
 	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
diff --git a/configs/imx6q_logic_defconfig b/configs/imx6q_logic_defconfig
index 036069a437..d0362665bb 100644
--- a/configs/imx6q_logic_defconfig
+++ b/configs/imx6q_logic_defconfig
@@ -4,25 +4,25 @@ CONFIG_SYS_TEXT_BASE=0x17800000
 CONFIG_SPL_GPIO_SUPPORT=y
 CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_TARGET_MX6LOGICPD=y
+CONFIG_SPL_MMC_SUPPORT=y
 CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_SYS_MALLOC_F_LEN=0x400
 CONFIG_SPL=y
+CONFIG_SPL_FAT_SUPPORT=y
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_NR_DRAM_BANKS=1
-CONFIG_TPL_SYS_MALLOC_F_LEN=0x400
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
 CONFIG_BOOTDELAY=3
 # CONFIG_USE_BOOTCOMMAND is not set
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
-# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
 CONFIG_SPL_SEPARATE_BSS=y
+# CONFIG_TPL_BANNER_PRINT is not set
+# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
 CONFIG_SPL_DMA_SUPPORT=y
 CONFIG_SPL_I2C_SUPPORT=y
 CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_SPL_OS_BOOT=y
+CONFIG_SPL_PAYLOAD="u-boot.img"
 CONFIG_SPL_USB_HOST_SUPPORT=y
 CONFIG_SPL_USB_GADGET_SUPPORT=y
 CONFIG_SPL_USB_SDP_SUPPORT=y
@@ -47,11 +47,9 @@ CONFIG_CMD_MTDPARTS=y
 CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:2m(spl),2m(uboot),1m(env),16m(kernel),1m(dtb),-(fs)"
 CONFIG_CMD_UBI=y
-CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="imx6q-logicpd"
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_SPL_DM=y
 CONFIG_PCF8575_GPIO=y
 CONFIG_SYS_I2C_MXC=y
 CONFIG_LED=y
@@ -64,7 +62,6 @@ CONFIG_PHY_ATHEROS=y
 CONFIG_FEC_MXC=y
 CONFIG_MII=y
 CONFIG_PINCTRL=y
-CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
 CONFIG_DM_PMIC_PFUZE100=y
 CONFIG_MXC_UART=y
-- 
2.17.1