[U-Boot] [PATCH v2] spl: eMMC/SD: Provide one __weak spl_boot_mode() function

Lukasz Majewski lukma at denx.de
Sat Feb 10 09:57:26 UTC 2018


Hi Jonathan,

> On Sat, Feb 10, 2018 at 01:45:16AM +0100, Lukasz Majewski wrote:
> > Hi Jonathan,
> >   
> > > On Sat, Feb 03, 2018 at 11:00:35AM -0200, Fabio Estevam wrote:  
> > > > On Sat, Feb 3, 2018 at 5:29 AM, Lukasz Majewski <lukma at denx.de>
> > > > wrote:    
> > > > > The goal of this patch is to clean up the code related to
> > > > > choosing SPL MMC boot mode.
> > > > >
> > > > > The spl_boot_mode() now is called only in spl_mmc_load_image()
> > > > > function, which is only compiled in if CONFIG_SPL_MMC_SUPPORT
> > > > > is enabled.
> > > > >
> > > > > To achieve the goal, all per mach/arch implementations
> > > > > eligible for unification has been replaced with one __weak
> > > > > implementation.
> > > > >
> > > > > Signed-off-by: Lukasz Majewski <lukma at denx.de>
> > > > > Reviewed-by: Marek Vasut <marex at denx.de>
> > > > > Reviewed-by: Stefano Babic <sbabic at denx.de>
> > > > > Acked-by: Michal Simek <michal.simek at xilinx.com> (For
> > > > > ZynqMP)    
> > > > 
> > > > Nice cleanup:
> > > > 
> > > > Reviewed-by: Fabio Estevam <fabio.estevam at nxp.com>    
> > > 
> > > This has broken booting via mmc with mx6cuboxi for me.
> > > 
> > > SPL loops on
> > > 
> > > U-Boot SPL 2018.03-rc1-00212-g48914fc119 (Feb 10 2018 - 11:04:33
> > > +1300) Trying to boot from MMC1
> > > Failed to mount ext2 filesystem...
> > > spl_load_image_ext: ext4fs mount err - 0  
> > 
> > Could you check what is the status of following defines in
> > your .config file:
> > 
> > CONFIG_SPL_FAT_SUPPORT
> > CONFIG_SUPPORT_EMMC_BOOT  
> 
> "# CONFIG_SPL_FAT_SUPPORT is not set"
> 
> CONFIG_SUPPORT_EMMC_BOOT is not in the .config at all
> 
> CONFIG_SPL_EXT_SUPPORT previously for imx6 would result in
> MMCSD_MODE_RAW but now it results in MMCSD_MODE_FS.
> 
> > 
> > And if by any chance your don't have:
> > CONFIG_SPL_EXT_SUPPORT defined?  
> 
> CONFIG_SPL_EXT_SUPPORT=y

Could you for test comment out the above define?

Thanks in advance,
Ɓukasz

> CONFIG_SPL_MMC_SUPPORT=y
> 
> mx6cuboxi_defconfig with no changes
> 
> > 
> > From what you have written above I assume that you boot from the
> > same medium - i.e. eMMC (so SPL and u-boot.img are on the same
> > medium) ?  
> 
> Both SPL and u-boot.img are on a microsd card.
> 
> The set CONFIG_SPL_* in .config are
> 
> CONFIG_SPL_SYS_THUMB_BUILD=y
> CONFIG_SPL_USE_ARCH_MEMCPY=y
> CONFIG_SPL_USE_ARCH_MEMSET=y
> CONFIG_SPL_LDSCRIPT="arch/arm/mach-omap2/u-boot-spl.lds"
> CONFIG_SPL_GPIO_SUPPORT=y
> CONFIG_SPL_LIBCOMMON_SUPPORT=y
> CONFIG_SPL_LIBGENERIC_SUPPORT=y
> CONFIG_SPL_MMC_SUPPORT=y
> CONFIG_SPL_SERIAL_SUPPORT=y
> CONFIG_SPL_LIBDISK_SUPPORT=y
> CONFIG_SPL_WATCHDOG_SUPPORT=y
> CONFIG_SPL_SYS_MALLOC_F_LEN=0x400
> CONFIG_SPL_BOOTSTAGE_RECORD_COUNT=5
> CONFIG_SPL_LOGLEVEL=4
> CONFIG_SPL=y
> CONFIG_SPL_LEGACY_IMAGE_SUPPORT=y
> CONFIG_SPL_EXT_SUPPORT=y
> CONFIG_SPL_I2C_SUPPORT=y
> CONFIG_SPL_DOS_PARTITION=y
> CONFIG_SPL_ISO_PARTITION=y
> CONFIG_SPL_EFI_PARTITION=y




Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180210/a4b2995b/attachment.sig>


More information about the U-Boot mailing list