[U-Boot] [PATCH v4 04/34] musb: sunxi: Add fifo config

Jagan Teki jagannadh.teki at gmail.com
Sun Feb 11 10:59:31 UTC 2018


On Tue, Feb 6, 2018 at 8:11 PM, Marek Vasut <marex at denx.de> wrote:
> On 02/06/2018 03:25 PM, Jagan Teki wrote:
>> Unlike other Allwinner SOC's H3/H5/V3s OTG support 4 endpoints
>> with relevant fifo configs, rest all have 5 endpoints.
>> So add the fifo configs and defer them based on udevice_id compatible.
>>
>> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
>> ---
>>  drivers/usb/musb-new/sunxi.c | 44 +++++++++++++++++++++++++++++++++++++++++++-
>>  1 file changed, 43 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/usb/musb-new/sunxi.c b/drivers/usb/musb-new/sunxi.c
>> index 0b7ff9f..562d311 100644
>> --- a/drivers/usb/musb-new/sunxi.c
>> +++ b/drivers/usb/musb-new/sunxi.c
>> @@ -301,13 +301,52 @@ static const struct musb_platform_ops sunxi_musb_ops = {
>>  #define SUNXI_MUSB_MAX_EP_NUM                6
>>  #define SUNXI_MUSB_RAM_BITS          11
>>
>> +static struct musb_fifo_cfg sunxi_musb_mode_cfg[] = {
>> +     MUSB_EP_FIFO_SINGLE(1, FIFO_TX, 512),
>> +     MUSB_EP_FIFO_SINGLE(1, FIFO_RX, 512),
>> +     MUSB_EP_FIFO_SINGLE(2, FIFO_TX, 512),
>> +     MUSB_EP_FIFO_SINGLE(2, FIFO_RX, 512),
>> +     MUSB_EP_FIFO_SINGLE(3, FIFO_TX, 512),
>> +     MUSB_EP_FIFO_SINGLE(3, FIFO_RX, 512),
>> +     MUSB_EP_FIFO_SINGLE(4, FIFO_TX, 512),
>> +     MUSB_EP_FIFO_SINGLE(4, FIFO_RX, 512),
>> +     MUSB_EP_FIFO_SINGLE(5, FIFO_TX, 512),
>> +     MUSB_EP_FIFO_SINGLE(5, FIFO_RX, 512),
>
> Generate all this programatically with a loop ?
>
>> +};
>> +
>> +/* H3/V3s OTG supports only 4 endpoints */
>> +#define SUNXI_MUSB_MAX_EP_NUM_H3     5
>> +
>> +static struct musb_fifo_cfg sunxi_musb_mode_cfg_h3[] = {
>> +     MUSB_EP_FIFO_SINGLE(1, FIFO_TX, 512),
>> +     MUSB_EP_FIFO_SINGLE(1, FIFO_RX, 512),
>> +     MUSB_EP_FIFO_SINGLE(2, FIFO_TX, 512),
>> +     MUSB_EP_FIFO_SINGLE(2, FIFO_RX, 512),
>> +     MUSB_EP_FIFO_SINGLE(3, FIFO_TX, 512),
>> +     MUSB_EP_FIFO_SINGLE(3, FIFO_RX, 512),
>> +     MUSB_EP_FIFO_SINGLE(4, FIFO_TX, 512),
>> +     MUSB_EP_FIFO_SINGLE(4, FIFO_RX, 512),
>> +};
>> +
>>  static struct musb_hdrc_config musb_config = {
>> +     .fifo_cfg       = sunxi_musb_mode_cfg,
>> +     .fifo_cfg_size  = ARRAY_SIZE(sunxi_musb_mode_cfg),
>>       .multipoint     = true,
>>       .dyn_fifo       = true,
>>       .num_eps        = SUNXI_MUSB_MAX_EP_NUM,
>>       .ram_bits       = SUNXI_MUSB_RAM_BITS,
>>  };
>>
>> +static struct musb_hdrc_config musb_config_h3 = {
>> +     .fifo_cfg       = sunxi_musb_mode_cfg_h3,
>> +     .fifo_cfg_size  = ARRAY_SIZE(sunxi_musb_mode_cfg_h3),
>> +     .multipoint     = true,
>> +     .dyn_fifo       = true,
>> +     .soft_con       = true,
>> +     .num_eps        = SUNXI_MUSB_MAX_EP_NUM_H3,
>> +     .ram_bits       = SUNXI_MUSB_RAM_BITS,
>> +};
>> +
>>  static int musb_usb_probe(struct udevice *dev)
>>  {
>>       struct sunxi_glue *glue = dev_get_priv(dev);
>> @@ -328,7 +367,10 @@ static int musb_usb_probe(struct udevice *dev)
>>
>>       pdata.power = 250;
>>       pdata.platform_ops = &sunxi_musb_ops;
>> -     pdata.config = &musb_config;
>> +     if (!device_is_compatible(dev, "allwinner,sun8i-h3-musb"))
>
> Instead of this, use the compatible's .data to pass the
> musb_config(_h3). Then you can do
> pdata.config = dev_get_driver_data(dev);

We've only diff with H3 compared to all other SOC's and this make
assigning same musb_config to non-H3 platforms, which will increasing
some bytes(as of now 16bytes we have a10,a33, a31 and h3). compatible
check here look suitable, I think.


More information about the U-Boot mailing list