[U-Boot] [PATCH 4/4] arm: zynq: Add parallel NOR flash mini u-boot configuration for zynq
Siva Durga Prasad Paladugu
siva.durga.paladugu at xilinx.com
Tue Jun 5 07:21:38 UTC 2018
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint OCM memory. This configuration
only has required parallel nor flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu at xilinx.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/zynq-cse-nor.dts | 88 ++++++++++++++++++++++++++++++++++++++++++
configs/zynq_cse_nor_defconfig | 50 ++++++++++++++++++++++++
3 files changed, 139 insertions(+)
create mode 100644 arch/arm/dts/zynq-cse-nor.dts
create mode 100644 configs/zynq_cse_nor_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 71b7c3a..9e29fe6 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -129,6 +129,7 @@ dtb-$(CONFIG_ARCH_UNIPHIER_SLD8) += \
dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-cc108.dtb \
zynq-cse-nand.dtb \
+ zynq-cse-nor.dtb \
zynq-cse-qspi-single.dtb \
zynq-microzed.dtb \
zynq-picozed.dtb \
diff --git a/arch/arm/dts/zynq-cse-nor.dts b/arch/arm/dts/zynq-cse-nor.dts
new file mode 100644
index 0000000..ba6f9a1
--- /dev/null
+++ b/arch/arm/dts/zynq-cse-nor.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Xilinx CSE NOR board DTS
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ */
+/dts-v1/;
+#include "zynq-7000.dtsi"
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "Zynq CSE NOR Board";
+ compatible = "xlnx,zynq-cse-nor", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &dcc;
+ };
+
+ memory at fffc0000 {
+ device_type = "memory";
+ reg = <0xFFFC0000 0x40000>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ dcc: dcc {
+ compatible = "arm,dcc";
+ status = "disabled";
+ u-boot,dm-pre-reloc;
+ };
+
+ amba: amba {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&intc>;
+ ranges;
+
+ intc: interrupt-controller at f8f01000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0xF8F01000 0x1000>,
+ <0xF8F00100 0x100>;
+ };
+
+ slcr: slcr at f8000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "xlnx,zynq-slcr", "syscon", "simple-bus";
+ reg = <0xF8000000 0x1000>;
+ ranges;
+ clkc: clkc at 100 {
+ #clock-cells = <1>;
+ compatible = "xlnx,ps7-clkc";
+ fclk-enable = <0xf>;
+ clock-output-names = "armpll", "ddrpll",
+ "iopll", "cpu_6or4x",
+ "cpu_3or2x", "cpu_2x", "cpu_1x",
+ "ddr2x", "ddr3x", "dci",
+ "lqspi", "smc", "pcap", "gem0",
+ "gem1", "fclk0", "fclk1",
+ "fclk2", "fclk3", "can0",
+ "can1", "sdio0", "sdio1",
+ "uart0", "uart1", "spi0",
+ "spi1", "dma", "usb0_aper",
+ "usb1_aper", "gem0_aper",
+ "gem1_aper", "sdio0_aper",
+ "sdio1_aper", "spi0_aper",
+ "spi1_aper", "can0_aper",
+ "can1_aper", "i2c0_aper",
+ "i2c1_aper", "uart0_aper",
+ "uart1_aper", "gpio_aper",
+ "lqspi_aper", "smc_aper",
+ "swdt", "dbg_trc", "dbg_apb";
+ reg = <0x100 0x100>;
+ };
+ };
+ };
+
+};
+
+&dcc {
+ status = "okay";
+};
diff --git a/configs/zynq_cse_nor_defconfig b/configs/zynq_cse_nor_defconfig
new file mode 100644
index 0000000..842d520
--- /dev/null
+++ b/configs/zynq_cse_nor_defconfig
@@ -0,0 +1,50 @@
+CONFIG_ARM=y
+CONFIG_SYS_CONFIG_NAME="zynq_cse"
+CONFIG_ARCH_ZYNQ=y
+CONFIG_SYS_TEXT_BASE=0xFFFC0000
+CONFIG_SPL_STACK_R_ADDR=0x200000
+CONFIG_SYS_MALLOC_LEN=0x1000
+CONFIG_ZYNQ_M29EW_WB_HACK=y
+CONFIG_DEFAULT_DEVICE_TREE="zynq-cse-nor"
+CONFIG_BOOTDELAY=-1
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_SPL=y
+CONFIG_SPL_STACK_R=y
+CONFIG_SYS_PROMPT="Zynq> "
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_CONSOLE is not set
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_BOOTM is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_FDT is not set
+# CONFIG_CMD_GO is not set
+# CONFIG_CMD_RUN is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_SPL is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+# CONFIG_CMD_EDITENV is not set
+# CONFIG_CMD_SAVEENV is not set
+# CONFIG_CMD_ENV_EXISTS is not set
+# CONFIG_CMD_CRC32 is not set
+# CONFIG_CMD_CLK is not set
+# CONFIG_CMD_DM is not set
+# CONFIG_CMD_FPGA is not set
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+# CONFIG_CMD_ECHO is not set
+# CONFIG_CMD_ITEST is not set
+# CONFIG_CMD_SOURCE is not set
+# CONFIG_CMD_SETEXPR is not set
+# CONFIG_CMD_NET is not set
+# CONFIG_CMD_NFS is not set
+# CONFIG_CMD_MISC is not set
+# CONFIG_PARTITIONS is not set
+CONFIG_OF_EMBED=y
+# CONFIG_DM_WARN is not set
+# CONFIG_DM_DEVICE_REMOVE is not set
+CONFIG_SPL_DM_SEQ_ALIAS=y
+# CONFIG_MMC is not set
+CONFIG_MTD_NOR_FLASH=y
+# CONFIG_EFI_LOADER is not set
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
More information about the U-Boot
mailing list