[U-Boot] [PATCH 3/4] arm: zynq: Add Nand flash mini u-boot configuration for zynq

[Michal Simek]

On 5.6.2018 09:21, Siva Durga Prasad Paladugu wrote:
> Add configuration files/dtses for mini u-boot configuration
> which runs on smaller footprint of memory. This configuration
> has only required nand flash support.
> 
> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu at xilinx.com>
> ---
>  arch/arm/dts/Makefile           |  1 +
>  arch/arm/dts/zynq-cse-nand.dts  | 90 +++++++++++++++++++++++++++++++++++++++++
>  configs/zynq_cse_nand_defconfig | 50 +++++++++++++++++++++++
>  3 files changed, 141 insertions(+)
>  create mode 100644 arch/arm/dts/zynq-cse-nand.dts
>  create mode 100644 configs/zynq_cse_nand_defconfig
> 
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index a0349a8..71b7c3a 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -128,6 +128,7 @@ dtb-$(CONFIG_ARCH_UNIPHIER_SLD8) += \
>  
>  dtb-$(CONFIG_ARCH_ZYNQ) += \
>  	zynq-cc108.dtb \
> +	zynq-cse-nand.dtb \
>  	zynq-cse-qspi-single.dtb \
>  	zynq-microzed.dtb \
>  	zynq-picozed.dtb \
> diff --git a/arch/arm/dts/zynq-cse-nand.dts b/arch/arm/dts/zynq-cse-nand.dts
> new file mode 100644
> index 0000000..9df5f9a
> --- /dev/null
> +++ b/arch/arm/dts/zynq-cse-nand.dts
> @@ -0,0 +1,90 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Xilinx CSE NAND board DTS
> + *
> + * Copyright (C) 2018 Xilinx, Inc.
> + */
> +/dts-v1/;
> +
> +/ {
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +	model = "Zynq CSE NAND Board";
> +	compatible = "xlnx,zynq-cse-nand", "xlnx,zynq-7000";
> +
> +	aliases {
> +		serial0 = &dcc;
> +	};
> +
> +	memory at fffc0000 {

this will be reported by latest DTC. This is


> +		device_type = "memory";
> +		reg = <0x0 0x400000>;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	dcc: dcc {
> +		compatible = "arm,dcc";
> +		status = "disabled";
> +		u-boot,dm-pre-reloc;
> +	};
> +
> +	amba: amba {
> +		u-boot,dm-pre-reloc;
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		interrupt-parent = <&intc>;
> +		ranges;
> +
> +		intc: interrupt-controller at f8f01000 {
> +			compatible = "arm,cortex-a9-gic";
> +			#interrupt-cells = <3>;
> +			interrupt-controller;
> +			reg = <0xF8F01000 0x1000>,
> +			      <0xF8F00100 0x100>;
> +		};

we can save some space by removing this intc node too.


> +
> +		slcr: slcr at f8000000 {
> +			u-boot,dm-pre-reloc;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			compatible = "xlnx,zynq-slcr", "syscon", "simple-bus";
> +			reg = <0xF8000000 0x1000>;
> +			ranges;
> +			clkc: clkc at 100 {
> +				u-boot,dm-pre-reloc;
> +				#clock-cells = <1>;
> +				compatible = "xlnx,ps7-clkc";
> +				fclk-enable = <0xf>;

we can remove this.

> +				clock-output-names = "armpll", "ddrpll",
> +						"iopll", "cpu_6or4x",
> +						"cpu_3or2x", "cpu_2x", "cpu_1x",
> +						"ddr2x", "ddr3x", "dci",
> +						"lqspi", "smc", "pcap", "gem0",
> +						"gem1", "fclk0", "fclk1",
> +						"fclk2", "fclk3", "can0",
> +						"can1", "sdio0", "sdio1",
> +						"uart0", "uart1", "spi0",
> +						"spi1", "dma", "usb0_aper",
> +						"usb1_aper", "gem0_aper",
> +						"gem1_aper", "sdio0_aper",
> +						"sdio1_aper", "spi0_aper",
> +						"spi1_aper", "can0_aper",
> +						"can1_aper", "i2c0_aper",
> +						"i2c1_aper", "uart0_aper",
> +						"uart1_aper", "gpio_aper",
> +						"lqspi_aper", "smc_aper",
> +						"swdt", "dbg_trc", "dbg_apb";
> +				reg = <0x100 0x100>;
> +			};
> +		};
> +	};
> +
> +};
> +
> +&dcc {
> +	status = "okay";
> +};
> diff --git a/configs/zynq_cse_nand_defconfig b/configs/zynq_cse_nand_defconfig
> new file mode 100644
> index 0000000..7c7e143
> --- /dev/null
> +++ b/configs/zynq_cse_nand_defconfig
> @@ -0,0 +1,50 @@
> +CONFIG_ARM=y
> +CONFIG_SYS_CONFIG_NAME="zynq_cse"
> +CONFIG_ARCH_ZYNQ=y
> +CONFIG_SYS_TEXT_BASE=0x100000
> +CONFIG_SPL_STACK_R_ADDR=0x200000
> +CONFIG_SYS_MALLOC_LEN=0x20000
> +CONFIG_DEFAULT_DEVICE_TREE="zynq-cse-nand"
> +# CONFIG_DISPLAY_CPUINFO is not set
> +CONFIG_SPL=y
> +CONFIG_SPL_STACK_R=y
> +CONFIG_SYS_PROMPT="Zynq> "
> +# CONFIG_CMD_BDI is not set
> +# CONFIG_CMD_CONSOLE is not set
> +# CONFIG_CMD_BOOTD is not set
> +# CONFIG_CMD_BOOTM is not set
> +# CONFIG_CMD_ELF is not set
> +# CONFIG_CMD_FDT is not set
> +# CONFIG_CMD_GO is not set
> +# CONFIG_CMD_RUN is not set
> +# CONFIG_CMD_IMI is not set
> +# CONFIG_CMD_XIMG is not set
> +# CONFIG_CMD_SPL is not set
> +# CONFIG_CMD_EXPORTENV is not set
> +# CONFIG_CMD_IMPORTENV is not set
> +# CONFIG_CMD_EDITENV is not set
> +# CONFIG_CMD_SAVEENV is not set
> +# CONFIG_CMD_ENV_EXISTS is not set
> +# CONFIG_CMD_CRC32 is not set
> +# CONFIG_CMD_CLK is not set
> +# CONFIG_CMD_DM is not set
> +# CONFIG_CMD_FLASH is not set
> +# CONFIG_CMD_FPGA is not set
> +# CONFIG_CMD_LOADB is not set
> +# CONFIG_CMD_LOADS is not set
> +# CONFIG_CMD_ECHO is not set
> +# CONFIG_CMD_ITEST is not set
> +# CONFIG_CMD_SOURCE is not set
> +# CONFIG_CMD_SETEXPR is not set
> +# CONFIG_CMD_NET is not set
> +# CONFIG_CMD_NFS is not set
> +# CONFIG_CMD_MISC is not set
> +# CONFIG_PARTITIONS is not set
> +CONFIG_OF_EMBED=y
> +# CONFIG_DM_WARN is not set
> +# CONFIG_DM_DEVICE_REMOVE is not set
> +CONFIG_SPL_DM_SEQ_ALIAS=y
> +# CONFIG_MMC is not set
> +CONFIG_NAND=y
> +CONFIG_NAND_ZYNQ=y
> +# CONFIG_EFI_LOADER is not set
> 


M