[U-Boot] [UBOOT PATCH v2 1/3] spi: xilinx: Read reg base address from DTS file

[Jagan Teki]

On Tue, Jun 12, 2018 at 11:34 AM, Vipul Kumar <vipul.kumar at xilinx.com> wrote:
> From: Michal Simek <michal.simek at xilinx.com>
>
> This patch added support to read register base address
> from DTS file.

This patch also adding fifo_depth apart from reg.

>
> Signed-off-by: Michal Simek <michal.simek at xilinx.com>
> Signed-off-by: Vipul Kumar <vipul.kumar at xilinx.com>
> ---
>  drivers/spi/xilinx_spi.c | 24 +++++++++++++++++-------
>  1 file changed, 17 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/spi/xilinx_spi.c b/drivers/spi/xilinx_spi.c
> index 8f0f32f..615106b 100644
> --- a/drivers/spi/xilinx_spi.c
> +++ b/drivers/spi/xilinx_spi.c
> @@ -77,10 +77,6 @@
>  #define CONFIG_XILINX_SPI_IDLE_VAL     GENMASK(7, 0)
>  #endif
>
> -#ifndef CONFIG_SYS_XILINX_SPI_LIST
> -#define CONFIG_SYS_XILINX_SPI_LIST     { CONFIG_SYS_SPI_BASE }
> -#endif
> -
>  /* xilinx spi register set */
>  struct xilinx_spi_regs {
>         u32 __space0__[7];
> @@ -105,16 +101,14 @@ struct xilinx_spi_priv {
>         struct xilinx_spi_regs *regs;
>         unsigned int freq;
>         unsigned int mode;
> +       unsigned int fifo_depth;
>  };
>
> -static unsigned long xilinx_spi_base_list[] = CONFIG_SYS_XILINX_SPI_LIST;
>  static int xilinx_spi_probe(struct udevice *bus)
>  {
>         struct xilinx_spi_priv *priv = dev_get_priv(bus);
>         struct xilinx_spi_regs *regs = priv->regs;
>
> -       priv->regs = (struct xilinx_spi_regs *)xilinx_spi_base_list[bus->seq];
> -
>         writel(SPISSR_RESET_VALUE, &regs->srr);
>
>         return 0;
> @@ -285,6 +279,21 @@ static const struct dm_spi_ops xilinx_spi_ops = {
>         .set_mode       = xilinx_spi_set_mode,
>  };
>
> +static int xilinx_spi_ofdata_to_platdata(struct udevice *bus)
> +{
> +       struct xilinx_spi_priv *priv = dev_get_priv(bus);
> +       struct udevice *dev = dev_get_parent(bus);
> +
> +       priv->regs = (struct xilinx_spi_regs *)devfdt_get_addr(bus);

Since the driver has OF_CONTROL support, better to get reg into probe
and skip platdata.

> +
> +       debug("%s: regs=%p\n", __func__, priv->regs);
> +
> +       priv->fifo_depth = fdtdec_get_int(gd->fdt_blob, dev_of_offset(bus),
> +                                         "fifo-size", 0);

Where this using? better to add it separate patch along with usage code.