[U-Boot] [PATCH v7 00/35] phy: sunxi: Add Allwinner sun4i USB PHY

[Jagan Teki]

Hi Jun,

On Mon, May 7, 2018 at 1:03 PM, Jagan Teki <jagan at amarulasolutions.com> wrote:
> This series rework of previous version where it removes legacy
> usb phy handling and added phy driver on generic-phy framework.
>
> Current implementation phy driver is unable to get pinctrl, clock
> and reset details from DT since the dm code on these will add it future.
>
> Changes for v7:
> - rebase on master
>
> Changes for v6:
> - Create private config for passing through driver_data instead
>   directly passing musb_config. This make room for adding new
>   configs in coming patches.
> - memset to pdata in musb-new/sunxi.c
>
> Changes for v5:
> - Rework of previous series
> - Used driver_data on sunxi.c since dt supported
> - tested on bpi-m2-plus, orangepi_pc2/prime, bananapi-m64
>
> Changes for v4:
> - Rework of previous series
> - Add Allwinner sun4i USB PHY driver
> - Drop legacy arch/arm/mach-sunxi/usb_phy.c and related code
>
> Chen-Yu Tsai (1):
>   sunxi: clock: Fix OHCI clock gating for H3/H5
>
> Jagan Teki (33):
>   usb: sunxi: Simplify ccm reg base code
>   musb: sunxi: Add proper macros instead of numericals
>   musb: sunxi: Use simple way to fill musb_hdrc pdata
>   musb: sunxi: Add fifo config
>   sunxi: clock: Fix clock gating for H3/H5/A64
>   musb: sunxi: Add OTG device clkgate and reset for H3/H5
>   musb: sunxi: Use BIT instead of numerical shift
>   musb: sunxi: Add support for H3/H5A64
>   phy: Add Allwinner A64 USB PHY driver
>   phy: sun4i-usb: Add id_detect and vbus_detect ops
>   phy: sun4i-usb: Add H3/H5 PHY config
>   phy: sun4i-usb: Add V3S PHY config
>   phy: sun4i-usb: Add A83T USB PHY config
>   phy: sun4i-usb: Add A10/A13/A20 PHY config
>   phy: sun4i-usb: Add A31 PHY config
>   phy: sun4i-usb: Add A33 USB PHY config
>   phy: sun4i-usb: Add A23 USB PHY config
>   device-tree-bindings: phy: Sync sun4i-usb-phy bindings
>   board: sunxi: Use generic-phy for board_usb_cable_connected
>   phy: sun4i-usb: Add a sunxi specific function for setting
>     squelch-detect
>   usb: sunxi: Switch to use generic-phy
>   sunxi: Drop legacy usb_phy.c
>   arm64: allwinner: a64: bananapi-m64: Sync usb_otg node from Linux
>   configs: bananapi-m64: Enable USB OTG peripheral mode
>   ARM: dts: sun8i: a83t: Sync usbphy node from Linux
>   arm64: allwinner: a64: bananapi-m64: Sync usb host nodes from Linux
>   ARM: dts: sun8i-h3: bananapi-m2-plus: Sync usb otg nodes from Linux
>   configs: bananapi-m2-plus: Enable USB OTG peripheral mode
>   arm64: allwinner: h5: orangepi-pc2: Order nodes in alphabetic
>   arm64: allwinner: h5: orangepi-pc2: Sync usb otg nodes from Linux
>   configs: orangepi-pc2: Enable USB OTG peripheral mode
>   arm64: allwinner: h5: orangepi-prime: Sync usb otg nodes from Linux
>   configs: orangepi-prime: Enable USB OTG peripheral mode
>
> Jun Nie (1):
>   sunxi: h3: Sync OTG and HCI nodes from Linux DT

I've verified H3/H5 boards and can you do it from your side?

Jagan.