[U-Boot] [PATCH v3 1/2] spi: zynqmp_gqspi: Add support for ZynqMP qspi driver
Siva Durga Prasad Paladugu
siva.durga.paladugu at xilinx.com
Tue May 8 10:13:15 UTC 2018
This patch adds qspi driver support for ZynqMP SoC. This
driver is responsible for communicating with qspi flash
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu at xilinx.com>
---
Changes for v3:
- Renamed all macros, functions, files and configs as per comment
- Used wait_for_bit wherever required
- Removed unnecessary header inclusion
Changes for v2:
- Rebased on top of latest master
- Moved macro definitions to .h file as per comment
- Fixed magic values with macros as per comment
---
arch/arm/include/asm/arch-zynqmp/zynqmp_gqspi.h | 154 ++++++
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/zynqmp_gqspi.c | 670 ++++++++++++++++++++++++
4 files changed, 832 insertions(+)
create mode 100644 arch/arm/include/asm/arch-zynqmp/zynqmp_gqspi.h
create mode 100644 drivers/spi/zynqmp_gqspi.c
diff --git a/arch/arm/include/asm/arch-zynqmp/zynqmp_gqspi.h b/arch/arm/include/asm/arch-zynqmp/zynqmp_gqspi.h
new file mode 100644
index 0000000..4b26d80
--- /dev/null
+++ b/arch/arm/include/asm/arch-zynqmp/zynqmp_gqspi.h
@@ -0,0 +1,154 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2018 Xilinx
+ *
+ * Xilinx ZynqMP Generic Quad-SPI(QSPI) controller
+ * driver (master mode only)
+ */
+
+#ifndef _ASM_ARCH_ZYNQMP_GQSPI_H_
+#define _ASM_ARCH_ZYNQMP_GQSPI_H_
+
+#define GQSPI_GFIFO_STRT_MODE_MASK BIT(29)
+#define GQSPI_CONFIG_MODE_EN_MASK (3 << 30)
+#define GQSPI_CONFIG_DMA_MODE (2 << 30)
+#define GQSPI_CONFIG_CPHA_MASK BIT(2)
+#define GQSPI_CONFIG_CPOL_MASK BIT(1)
+
+/* QSPI MIO's count for different connection topologies */
+#define GQSPI_MIO_NUM_QSPI0 6
+#define GQSPI_MIO_NUM_QSPI1 5
+#define GQSPI_MIO_NUM_QSPI1_CS 1
+
+/*
+ * QSPI Interrupt Registers bit Masks
+ *
+ * All the four interrupt registers (Status/Mask/Enable/Disable) have the same
+ * bit definitions.
+ */
+#define GQSPI_IXR_TXNFULL_MASK 0x00000004 /* QSPI TX FIFO Overflow */
+#define GQSPI_IXR_TXFULL_MASK 0x00000008 /* QSPI TX FIFO is full */
+#define GQSPI_IXR_RXNEMTY_MASK 0x00000010 /* QSPI RX FIFO Not Empty */
+#define GQSPI_IXR_GFEMTY_MASK 0x00000080 /* QSPI Generic FIFO Empty */
+#define GQSPI_IXR_ALL_MASK (GQSPI_IXR_TXNFULL_MASK | \
+ GQSPI_IXR_RXNEMTY_MASK)
+
+/*
+ * QSPI Enable Register bit Masks
+ *
+ * This register is used to enable or disable the QSPI controller
+ */
+#define GQSPI_ENABLE_ENABLE_MASK 0x00000001 /* QSPI Enable Bit Mask */
+
+#define GQSPI_GFIFO_LOW_BUS BIT(14)
+#define GQSPI_GFIFO_CS_LOWER BIT(12)
+#define GQSPI_GFIFO_UP_BUS BIT(15)
+#define GQSPI_GFIFO_CS_UPPER BIT(13)
+#define GQSPI_SPI_MODE_QSPI (3 << 10)
+#define GQSPI_SPI_MODE_SPI BIT(10)
+#define GQSPI_SPI_MODE_DUAL_SPI (2 << 10)
+#define GQSPI_IMD_DATA_CS_ASSERT 5
+#define GQSPI_IMD_DATA_CS_DEASSERT 5
+#define GQSPI_GFIFO_TX BIT(16)
+#define GQSPI_GFIFO_RX BIT(17)
+#define GQSPI_GFIFO_STRIPE_MASK BIT(18)
+#define GQSPI_GFIFO_IMD_MASK 0xFF
+#define GQSPI_GFIFO_EXP_MASK BIT(9)
+#define GQSPI_GFIFO_DATA_XFR_MASK BIT(8)
+#define GQSPI_STRT_GEN_FIFO BIT(28)
+#define GQSPI_GEN_FIFO_STRT_MOD BIT(29)
+#define GQSPI_GFIFO_WP_HOLD BIT(19)
+#define GQSPI_BAUD_DIV_MASK (7 << 3)
+#define GQSPI_DFLT_BAUD_RATE_DIV BIT(3)
+#define GQSPI_GFIFO_ALL_INT_MASK 0xFBE
+#define GQSPI_DMA_DST_I_STS_DONE BIT(1)
+#define GQSPI_DMA_DST_I_STS_MASK 0xFE
+#define MODEBITS 0x6
+
+#define QUAD_OUT_READ_CMD 0x6B
+#define QUAD_PAGE_PROGRAM_CMD 0x32
+#define DUAL_OUTPUT_FASTRD_CMD 0x3B
+
+#define GQSPI_GFIFO_SELECT BIT(0)
+
+#define GQSPI_FIFO_THRESHOLD 1
+
+#define SPI_XFER_ON_BOTH 0
+#define SPI_XFER_ON_LOWER 1
+#define SPI_XFER_ON_UPPER 2
+
+#define GQSPI_DMA_ALIGN 0x4
+#define GQSPI_MAX_BAUD_RATE_VAL 7
+#define GQSPI_DFLT_BAUD_RATE_VAL 2
+
+#define GQSPI_TIMEOUT 100000000
+
+#define GQSPI_BAUD_DIV_SHIFT 2
+#define GQSPI_LPBK_DLY_ADJ_LPBK_SHIFT 5
+#define GQSPI_LPBK_DLY_ADJ_DLY_1 0x2
+#define GQSPI_LPBK_DLY_ADJ_DLY_1_SHIFT 3
+#define GQSPI_LPBK_DLY_ADJ_DLY_0 0x3
+#define GQSPI_USE_DATA_DLY 0x1
+#define GQSPI_USE_DATA_DLY_SHIFT 31
+#define GQSPI_DATA_DLY_ADJ_VALUE 0x2
+#define GQSPI_DATA_DLY_ADJ_SHIFT 28
+#define TAP_DLY_BYPASS_LQSPI_RX_VALUE 0x1
+#define TAP_DLY_BYPASS_LQSPI_RX_SHIFT 2
+#define GQSPI_DATA_DLY_ADJ_OFST 0x000001F8
+#define IOU_TAPDLY_BYPASS_OFST 0xFF180390
+#define GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK 0x00000020
+#define GQSPI_FREQ_40MHZ 40000000
+#define GQSPI_FREQ_100MHZ 100000000
+#define GQSPI_FREQ_150MHZ 150000000
+#define IOU_TAPDLY_BYPASS_MASK 0x7
+
+#define GQSPI_REG_OFFSET 0x100
+#define GQSPI_DMA_REG_OFFSET 0x800
+
+/* QSPI register offsets */
+struct zynqmp_qspi_regs {
+ u32 confr; /* 0x00 */
+ u32 isr; /* 0x04 */
+ u32 ier; /* 0x08 */
+ u32 idisr; /* 0x0C */
+ u32 imaskr; /* 0x10 */
+ u32 enbr; /* 0x14 */
+ u32 dr; /* 0x18 */
+ u32 txd0r; /* 0x1C */
+ u32 drxr; /* 0x20 */
+ u32 sicr; /* 0x24 */
+ u32 txftr; /* 0x28 */
+ u32 rxftr; /* 0x2C */
+ u32 gpior; /* 0x30 */
+ u32 reserved0; /* 0x34 */
+ u32 lpbkdly; /* 0x38 */
+ u32 reserved1; /* 0x3C */
+ u32 genfifo; /* 0x40 */
+ u32 gqspisel; /* 0x44 */
+ u32 reserved2; /* 0x48 */
+ u32 gqfifoctrl; /* 0x4C */
+ u32 gqfthr; /* 0x50 */
+ u32 gqpollcfg; /* 0x54 */
+ u32 gqpollto; /* 0x58 */
+ u32 gqxfersts; /* 0x5C */
+ u32 gqfifosnap; /* 0x60 */
+ u32 gqrxcpy; /* 0x64 */
+ u32 reserved3[36]; /* 0x68 */
+ u32 gqspidlyadj; /* 0xF8 */
+};
+
+struct zynqmp_qspi_dma_regs {
+ u32 dmadst; /* 0x00 */
+ u32 dmasize; /* 0x04 */
+ u32 dmasts; /* 0x08 */
+ u32 dmactrl; /* 0x0C */
+ u32 reserved0; /* 0x10 */
+ u32 dmaisr; /* 0x14 */
+ u32 dmaier; /* 0x18 */
+ u32 dmaidr; /* 0x1C */
+ u32 dmaimr; /* 0x20 */
+ u32 dmactrl2; /* 0x24 */
+ u32 dmadstmsb; /* 0x28 */
+};
+
+#endif /* _ASM_ARCH_ZYNQMP_GQSPI_H_ */
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 6667f73..269af6f 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -222,6 +222,13 @@ config ZYNQ_QSPI
Zynq QSPI IP core. This IP is used to connect the flash in
4-bit qspi, 8-bit dual stacked and shared 4-bit dual parallel.
+config ZYNQMP_GQSPI
+ bool "Configure ZynqMP Generic QSPI"
+ depends on ARCH_ZYNQMP
+ help
+ This option is used to enable ZynqMP QSPI controller driver which
+ is used to communicate with qspi flash devices.
+
endif # if DM_SPI
config SOFT_SPI
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 176bfa0..29c77c3 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -53,3 +53,4 @@ obj-$(CONFIG_TI_QSPI) += ti_qspi.o
obj-$(CONFIG_XILINX_SPI) += xilinx_spi.o
obj-$(CONFIG_ZYNQ_SPI) += zynq_spi.o
obj-$(CONFIG_ZYNQ_QSPI) += zynq_qspi.o
+obj-$(CONFIG_ZYNQMP_GQSPI) += zynqmp_gqspi.o
diff --git a/drivers/spi/zynqmp_gqspi.c b/drivers/spi/zynqmp_gqspi.c
new file mode 100644
index 0000000..ceb3745
--- /dev/null
+++ b/drivers/spi/zynqmp_gqspi.c
@@ -0,0 +1,670 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2018 Xilinx
+ *
+ * Xilinx ZynqMP Generic Quad-SPI(QSPI) controller driver(master mode only)
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <memalign.h>
+#include <ubi_uboot.h>
+#include <spi.h>
+#include <spi_flash.h>
+#include <asm/io.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/clk.h>
+#include <clk.h>
+#include <asm/arch/zynqmp_gqspi.h>
+#include <wait_bit.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct zynqmp_qspi_platdata {
+ struct zynqmp_qspi_regs *regs;
+ struct zynqmp_qspi_dma_regs *dma_regs;
+ u32 frequency;
+ u32 speed_hz;
+ unsigned int tx_rx_mode;
+};
+
+struct zynqmp_qspi_priv {
+ struct zynqmp_qspi_regs *regs;
+ struct zynqmp_qspi_dma_regs *dma_regs;
+ u8 mode;
+ const void *tx_buf;
+ void *rx_buf;
+ unsigned int len;
+ int bytes_to_transfer;
+ int bytes_to_receive;
+ unsigned int is_inst;
+ unsigned int cs_change:1;
+};
+
+static u8 last_cmd;
+
+static int zynqmp_qspi_ofdata_to_platdata(struct udevice *bus)
+{
+ struct zynqmp_qspi_platdata *plat = bus->platdata;
+ u32 mode = 0;
+ u32 value;
+ int ret;
+ struct clk clk;
+ unsigned long clock;
+
+ debug("%s\n", __func__);
+
+ plat->regs = (struct zynqmp_qspi_regs *)(devfdt_get_addr(bus) +
+ GQSPI_REG_OFFSET);
+ plat->dma_regs = (struct zynqmp_qspi_dma_regs *)
+ (devfdt_get_addr(bus) + GQSPI_DMA_REG_OFFSET);
+
+ ret = clk_get_by_index(bus, 0, &clk);
+ if (ret < 0) {
+ dev_err(dev, "failed to get clock\n");
+ return ret;
+ }
+
+ clock = clk_get_rate(&clk);
+ if (IS_ERR_VALUE(clock)) {
+ dev_err(dev, "failed to get rate\n");
+ return clock;
+ }
+ debug("%s: CLK %ld\n", __func__, clock);
+
+ ret = clk_enable(&clk);
+ if (ret && ret != -ENOSYS) {
+ dev_err(dev, "failed to enable clock\n");
+ return ret;
+ }
+
+ value = dev_read_u32_default(bus, "spi-rx-bus-width", 1);
+ switch (value) {
+ case 1:
+ break;
+ case 2:
+ mode |= SPI_RX_DUAL;
+ break;
+ case 4:
+ mode |= SPI_RX_QUAD;
+ break;
+ default:
+ printf("Invalid spi-rx-bus-width %d\n", value);
+ break;
+ }
+
+ value = dev_read_u32_default(bus, "spi-tx-bus-width", 1);
+ switch (value) {
+ case 1:
+ break;
+ case 2:
+ mode |= SPI_TX_DUAL;
+ break;
+ case 4:
+ mode |= SPI_TX_QUAD;
+ break;
+ default:
+ printf("Invalid spi-tx-bus-width %d\n", value);
+ break;
+ }
+
+ plat->tx_rx_mode = mode;
+
+ plat->frequency = clock;
+ plat->speed_hz = plat->frequency;
+
+ return 0;
+}
+
+static void zynqmp_qspi_init_hw(struct zynqmp_qspi_priv *priv)
+{
+ u32 config_reg;
+ struct zynqmp_qspi_regs *regs = priv->regs;
+
+ writel(GQSPI_GFIFO_SELECT, ®s->gqspisel);
+ writel(GQSPI_GFIFO_ALL_INT_MASK, ®s->idisr);
+ writel(GQSPI_FIFO_THRESHOLD, ®s->txftr);
+ writel(GQSPI_FIFO_THRESHOLD, ®s->rxftr);
+ writel(GQSPI_GFIFO_ALL_INT_MASK, ®s->isr);
+
+ config_reg = readl(®s->confr);
+ config_reg &= ~(GQSPI_GFIFO_STRT_MODE_MASK |
+ GQSPI_CONFIG_MODE_EN_MASK);
+ config_reg |= GQSPI_CONFIG_DMA_MODE |
+ GQSPI_GFIFO_WP_HOLD |
+ GQSPI_DFLT_BAUD_RATE_DIV;
+ writel(config_reg, ®s->confr);
+
+ writel(GQSPI_ENABLE_ENABLE_MASK, ®s->enbr);
+}
+
+static u32 zynqmp_qspi_bus_select(struct zynqmp_qspi_priv *priv)
+{
+ u32 gqspi_fifo_reg = 0;
+
+ gqspi_fifo_reg = GQSPI_GFIFO_LOW_BUS |
+ GQSPI_GFIFO_CS_LOWER;
+
+ return gqspi_fifo_reg;
+}
+
+static void zynqmp_qspi_fill_gen_fifo(struct zynqmp_qspi_priv *priv,
+ u32 gqspi_fifo_reg)
+{
+ struct zynqmp_qspi_regs *regs = priv->regs;
+ int ret = 0;
+
+ ret = wait_for_bit_le32(®s->isr, GQSPI_IXR_GFEMTY_MASK, 1,
+ GQSPI_TIMEOUT, 1);
+ if (ret)
+ printf("%s Timeout\n", __func__);
+
+ writel(gqspi_fifo_reg, ®s->genfifo);
+}
+
+static void zynqmp_qspi_chipselect(struct zynqmp_qspi_priv *priv, int is_on)
+{
+ u32 gqspi_fifo_reg = 0;
+
+ if (is_on) {
+ gqspi_fifo_reg = zynqmp_qspi_bus_select(priv);
+ gqspi_fifo_reg |= GQSPI_SPI_MODE_SPI |
+ GQSPI_IMD_DATA_CS_ASSERT;
+ } else {
+ gqspi_fifo_reg = GQSPI_GFIFO_LOW_BUS;
+ gqspi_fifo_reg |= GQSPI_IMD_DATA_CS_DEASSERT;
+ }
+
+ debug("GFIFO_CMD_CS: 0x%x\n", gqspi_fifo_reg);
+
+ zynqmp_qspi_fill_gen_fifo(priv, gqspi_fifo_reg);
+}
+
+void zynqmp_qspi_set_tapdelay(struct udevice *bus, u32 baudrateval)
+{
+ struct zynqmp_qspi_platdata *plat = bus->platdata;
+ struct zynqmp_qspi_priv *priv = dev_get_priv(bus);
+ struct zynqmp_qspi_regs *regs = priv->regs;
+ u32 tapdlybypass = 0, lpbkdlyadj = 0, datadlyadj = 0, clk_rate;
+ u32 reqhz = 0;
+
+ clk_rate = plat->frequency;
+ reqhz = (clk_rate / (GQSPI_BAUD_DIV_SHIFT << baudrateval));
+
+ debug("%s, req_hz:%d, clk_rate:%d, baudrateval:%d\n",
+ __func__, reqhz, clk_rate, baudrateval);
+
+ if (reqhz < GQSPI_FREQ_40MHZ) {
+ zynqmp_mmio_read(IOU_TAPDLY_BYPASS_OFST, &tapdlybypass);
+ tapdlybypass |= (TAP_DLY_BYPASS_LQSPI_RX_VALUE <<
+ TAP_DLY_BYPASS_LQSPI_RX_SHIFT);
+ } else if (reqhz < GQSPI_FREQ_100MHZ) {
+ zynqmp_mmio_read(IOU_TAPDLY_BYPASS_OFST, &tapdlybypass);
+ tapdlybypass |= (TAP_DLY_BYPASS_LQSPI_RX_VALUE <<
+ TAP_DLY_BYPASS_LQSPI_RX_SHIFT);
+ lpbkdlyadj = readl(®s->lpbkdly);
+ lpbkdlyadj |= (GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK);
+ datadlyadj = readl(®s->gqspidlyadj);
+ datadlyadj |= ((GQSPI_USE_DATA_DLY << GQSPI_USE_DATA_DLY_SHIFT)
+ | (GQSPI_DATA_DLY_ADJ_VALUE <<
+ GQSPI_DATA_DLY_ADJ_SHIFT));
+ } else if (reqhz < GQSPI_FREQ_150MHZ) {
+ lpbkdlyadj = readl(®s->lpbkdly);
+ lpbkdlyadj |= ((GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK) |
+ GQSPI_LPBK_DLY_ADJ_DLY_0);
+ }
+
+ zynqmp_mmio_write(IOU_TAPDLY_BYPASS_OFST, IOU_TAPDLY_BYPASS_MASK,
+ tapdlybypass);
+ writel(lpbkdlyadj, ®s->lpbkdly);
+ writel(datadlyadj, ®s->gqspidlyadj);
+}
+
+static int zynqmp_qspi_set_speed(struct udevice *bus, uint speed)
+{
+ struct zynqmp_qspi_platdata *plat = bus->platdata;
+ struct zynqmp_qspi_priv *priv = dev_get_priv(bus);
+ struct zynqmp_qspi_regs *regs = priv->regs;
+ u32 confr;
+ u8 baud_rate_val = 0;
+
+ debug("%s\n", __func__);
+ if (speed > plat->frequency)
+ speed = plat->frequency;
+
+ /* Set the clock frequency */
+ confr = readl(®s->confr);
+ if (speed == 0) {
+ /* Set baudrate x8, if the freq is 0 */
+ baud_rate_val = GQSPI_DFLT_BAUD_RATE_VAL;
+ } else if (plat->speed_hz != speed) {
+ while ((baud_rate_val < 8) &&
+ ((plat->frequency /
+ (2 << baud_rate_val)) > speed))
+ baud_rate_val++;
+
+ if (baud_rate_val > GQSPI_MAX_BAUD_RATE_VAL)
+ baud_rate_val = GQSPI_DFLT_BAUD_RATE_VAL;
+
+ plat->speed_hz = plat->frequency / (2 << baud_rate_val);
+ }
+ confr &= ~GQSPI_BAUD_DIV_MASK;
+ confr |= (baud_rate_val << 3);
+ writel(confr, ®s->confr);
+
+ zynqmp_qspi_set_tapdelay(bus, baud_rate_val);
+ debug("regs=%p, speed=%d\n", priv->regs, plat->speed_hz);
+
+ return 0;
+}
+
+static int zynqmp_qspi_child_pre_probe(struct udevice *bus)
+{
+ struct spi_slave *slave = dev_get_parent_priv(bus);
+ struct zynqmp_qspi_platdata *plat = dev_get_platdata(bus->parent);
+
+ slave->mode = plat->tx_rx_mode;
+
+ return 0;
+}
+
+static int zynqmp_qspi_probe(struct udevice *bus)
+{
+ struct zynqmp_qspi_platdata *plat = dev_get_platdata(bus);
+ struct zynqmp_qspi_priv *priv = dev_get_priv(bus);
+
+ debug("%s: bus:%p, priv:%p\n", __func__, bus, priv);
+
+ priv->regs = plat->regs;
+ priv->dma_regs = plat->dma_regs;
+
+ /* init the zynq spi hw */
+ zynqmp_qspi_init_hw(priv);
+
+ return 0;
+}
+
+static int zynqmp_qspi_set_mode(struct udevice *bus, uint mode)
+{
+ struct zynqmp_qspi_priv *priv = dev_get_priv(bus);
+ struct zynqmp_qspi_regs *regs = priv->regs;
+ u32 confr;
+
+ debug("%s\n", __func__);
+ /* Set the SPI Clock phase and polarities */
+ confr = readl(®s->confr);
+ confr &= ~(GQSPI_CONFIG_CPHA_MASK |
+ GQSPI_CONFIG_CPOL_MASK);
+
+ if (priv->mode & SPI_CPHA)
+ confr |= GQSPI_CONFIG_CPHA_MASK;
+ if (priv->mode & SPI_CPOL)
+ confr |= GQSPI_CONFIG_CPOL_MASK;
+
+ priv->mode = mode;
+ writel(confr, ®s->confr);
+
+ debug("regs=%p, mode=%d\n", priv->regs, priv->mode);
+
+ return 0;
+}
+
+static int zynqmp_qspi_fill_tx_fifo(struct zynqmp_qspi_priv *priv, u32 size)
+{
+ u32 data;
+ int ret = 0;
+ struct zynqmp_qspi_regs *regs = priv->regs;
+ u32 *buf = (u32 *)priv->tx_buf;
+ u32 len = size;
+
+ debug("TxFIFO: 0x%x, size: 0x%x\n", readl(®s->isr),
+ size);
+
+ while (size) {
+ ret = wait_for_bit_le32(®s->isr, GQSPI_IXR_TXNFULL_MASK, 1,
+ GQSPI_TIMEOUT, 1);
+ if (ret) {
+ printf("%s: Timeout\n", __func__);
+ return ret;
+ }
+
+ if (size >= 4) {
+ writel(*buf, ®s->txd0r);
+ buf++;
+ size -= 4;
+ } else {
+ switch (size) {
+ case 1:
+ data = *((u8 *)buf);
+ buf += 1;
+ data |= 0xFFFFFF00;
+ break;
+ case 2:
+ data = *((u16 *)buf);
+ buf += 2;
+ data |= 0xFFFF0000;
+ break;
+ case 3:
+ data = *((u16 *)buf);
+ buf += 2;
+ data |= (*((u8 *)buf) << 16);
+ buf += 1;
+ data |= 0xFF000000;
+ break;
+ }
+ writel(data, ®s->txd0r);
+ size = 0;
+ }
+ }
+
+ priv->tx_buf += len;
+ return 0;
+}
+
+static void zynqmp_qspi_genfifo_cmd(struct zynqmp_qspi_priv *priv)
+{
+ u8 command = 1;
+ u32 gen_fifo_cmd;
+ u32 bytecount = 0;
+
+ while (priv->len) {
+ gen_fifo_cmd = zynqmp_qspi_bus_select(priv);
+ gen_fifo_cmd |= GQSPI_GFIFO_TX;
+
+ if (command) {
+ command = 0;
+ last_cmd = *(u8 *)priv->tx_buf;
+ }
+
+ gen_fifo_cmd |= GQSPI_SPI_MODE_SPI;
+ gen_fifo_cmd |= *(u8 *)priv->tx_buf;
+ bytecount++;
+ priv->len--;
+ priv->tx_buf = (u8 *)priv->tx_buf + 1;
+
+ debug("GFIFO_CMD_Cmd = 0x%x\n", gen_fifo_cmd);
+
+ zynqmp_qspi_fill_gen_fifo(priv, gen_fifo_cmd);
+ }
+}
+
+static u32 zynqmp_qspi_calc_exp(struct zynqmp_qspi_priv *priv,
+ u32 *gen_fifo_cmd)
+{
+ u32 expval = 8;
+ u32 len;
+
+ while (1) {
+ if (priv->len > 255) {
+ if (priv->len & (1 << expval)) {
+ *gen_fifo_cmd &= ~GQSPI_GFIFO_IMD_MASK;
+ *gen_fifo_cmd |= GQSPI_GFIFO_EXP_MASK;
+ *gen_fifo_cmd |= expval;
+ priv->len -= (1 << expval);
+ return expval;
+ }
+ expval++;
+ } else {
+ *gen_fifo_cmd &= ~(GQSPI_GFIFO_IMD_MASK |
+ GQSPI_GFIFO_EXP_MASK);
+ *gen_fifo_cmd |= (u8)priv->len;
+ len = (u8)priv->len;
+ priv->len = 0;
+ return len;
+ }
+ }
+}
+
+static int zynqmp_qspi_genfifo_fill_tx(struct zynqmp_qspi_priv *priv)
+{
+ u32 gen_fifo_cmd;
+ u32 len;
+ int ret = 0;
+
+ gen_fifo_cmd = zynqmp_qspi_bus_select(priv);
+ gen_fifo_cmd |= GQSPI_GFIFO_TX |
+ GQSPI_GFIFO_DATA_XFR_MASK;
+
+ if (last_cmd == QUAD_PAGE_PROGRAM_CMD)
+ gen_fifo_cmd |= GQSPI_SPI_MODE_QSPI;
+ else
+ gen_fifo_cmd |= GQSPI_SPI_MODE_SPI;
+
+ while (priv->len) {
+ len = zynqmp_qspi_calc_exp(priv, &gen_fifo_cmd);
+ zynqmp_qspi_fill_gen_fifo(priv, gen_fifo_cmd);
+
+ debug("GFIFO_CMD_TX:0x%x\n", gen_fifo_cmd);
+
+ if (gen_fifo_cmd & GQSPI_GFIFO_EXP_MASK)
+ ret = zynqmp_qspi_fill_tx_fifo(priv,
+ 1 << len);
+ else
+ ret = zynqmp_qspi_fill_tx_fifo(priv,
+ len);
+
+ if (ret)
+ return ret;
+ }
+ return ret;
+}
+
+static int zynqmp_qspi_start_dma(struct zynqmp_qspi_priv *priv,
+ u32 gen_fifo_cmd, u32 *buf)
+{
+ u32 addr;
+ u32 size, len;
+ u32 actuallen = priv->len;
+ int ret = 0;
+ struct zynqmp_qspi_dma_regs *dma_regs = priv->dma_regs;
+
+ writel((unsigned long)buf, &dma_regs->dmadst);
+ writel(roundup(priv->len, 4), &dma_regs->dmasize);
+ writel(GQSPI_DMA_DST_I_STS_MASK, &dma_regs->dmaier);
+ addr = (unsigned long)buf;
+ size = roundup(priv->len, ARCH_DMA_MINALIGN);
+ flush_dcache_range(addr, addr + size);
+
+ while (priv->len) {
+ len = zynqmp_qspi_calc_exp(priv, &gen_fifo_cmd);
+ if (!(gen_fifo_cmd & GQSPI_GFIFO_EXP_MASK) &&
+ (len % 4)) {
+ gen_fifo_cmd &= ~(0xFF);
+ gen_fifo_cmd |= (len / 4 + 1) * 4;
+ }
+ zynqmp_qspi_fill_gen_fifo(priv, gen_fifo_cmd);
+
+ debug("GFIFO_CMD_RX:0x%x\n", gen_fifo_cmd);
+ }
+
+ ret = wait_for_bit_le32(&dma_regs->dmaisr, GQSPI_DMA_DST_I_STS_DONE,
+ 1, GQSPI_TIMEOUT, 1);
+ if (ret) {
+ printf("DMA Timeout:0x%x\n", readl(&dma_regs->dmaisr));
+ return -1;
+ }
+
+ writel(GQSPI_DMA_DST_I_STS_DONE, &dma_regs->dmaisr);
+
+ debug("buf:0x%lx, rxbuf:0x%lx, *buf:0x%x len: 0x%x\n",
+ (unsigned long)buf, (unsigned long)priv->rx_buf, *buf,
+ actuallen);
+
+ if (buf != priv->rx_buf)
+ memcpy(priv->rx_buf, buf, actuallen);
+
+ return 0;
+}
+
+static int zynqmp_qspi_genfifo_fill_rx(struct zynqmp_qspi_priv *priv)
+{
+ u32 gen_fifo_cmd;
+ u32 *buf;
+ u32 actuallen = priv->len;
+
+ gen_fifo_cmd = zynqmp_qspi_bus_select(priv);
+ gen_fifo_cmd |= GQSPI_GFIFO_RX |
+ GQSPI_GFIFO_DATA_XFR_MASK;
+
+ if (last_cmd == QUAD_OUT_READ_CMD)
+ gen_fifo_cmd |= GQSPI_SPI_MODE_QSPI;
+ else if (last_cmd == DUAL_OUTPUT_FASTRD_CMD)
+ gen_fifo_cmd |= GQSPI_SPI_MODE_DUAL_SPI;
+ else
+ gen_fifo_cmd |= GQSPI_SPI_MODE_SPI;
+
+ /*
+ * Check if receive buffer is aligned to 4 byte and length
+ * is multiples of four byte as we are using dma to receive.
+ */
+ if (!((unsigned long)priv->rx_buf & (GQSPI_DMA_ALIGN - 1)) &&
+ !(actuallen % GQSPI_DMA_ALIGN)) {
+ buf = (u32 *)priv->rx_buf;
+ return zynqmp_qspi_start_dma(priv, gen_fifo_cmd, buf);
+ }
+
+ ALLOC_CACHE_ALIGN_BUFFER(u8, tmp, roundup(priv->len,
+ GQSPI_DMA_ALIGN));
+ buf = (u32 *)tmp;
+ return zynqmp_qspi_start_dma(priv, gen_fifo_cmd, buf);
+}
+
+static int zynqmp_qspi_start_transfer(struct zynqmp_qspi_priv *priv)
+{
+ int ret = 0;
+
+ if (priv->is_inst) {
+ if (priv->tx_buf)
+ zynqmp_qspi_genfifo_cmd(priv);
+ else
+ ret = -1;
+ } else {
+ if (priv->tx_buf)
+ ret = zynqmp_qspi_genfifo_fill_tx(priv);
+ else if (priv->rx_buf)
+ ret = zynqmp_qspi_genfifo_fill_rx(priv);
+ else
+ ret = -1;
+ }
+ return ret;
+}
+
+static int zynqmp_qspi_transfer(struct zynqmp_qspi_priv *priv)
+{
+ static unsigned int cs_change = 1;
+ int status = 0;
+
+ debug("%s\n", __func__);
+
+ while (1) {
+ /* Select the chip if required */
+ if (cs_change)
+ zynqmp_qspi_chipselect(priv, 1);
+
+ cs_change = priv->cs_change;
+
+ if (!priv->tx_buf && !priv->rx_buf && priv->len) {
+ status = -1;
+ break;
+ }
+
+ /* Request the transfer */
+ if (priv->len) {
+ status = zynqmp_qspi_start_transfer(priv);
+ priv->is_inst = 0;
+ if (status < 0)
+ break;
+ }
+
+ if (cs_change)
+ /* Deselect the chip */
+ zynqmp_qspi_chipselect(priv, 0);
+ break;
+ }
+
+ return status;
+}
+
+static int zynqmp_qspi_claim_bus(struct udevice *dev)
+{
+ struct udevice *bus = dev->parent;
+ struct zynqmp_qspi_priv *priv = dev_get_priv(bus);
+ struct zynqmp_qspi_regs *regs = priv->regs;
+
+ debug("%s\n", __func__);
+ writel(GQSPI_ENABLE_ENABLE_MASK, ®s->enbr);
+
+ return 0;
+}
+
+static int zynqmp_qspi_release_bus(struct udevice *dev)
+{
+ struct udevice *bus = dev->parent;
+ struct zynqmp_qspi_priv *priv = dev_get_priv(bus);
+ struct zynqmp_qspi_regs *regs = priv->regs;
+
+ debug("%s\n", __func__);
+ writel(~GQSPI_ENABLE_ENABLE_MASK, ®s->enbr);
+
+ return 0;
+}
+
+int zynqmp_qspi_xfer(struct udevice *dev, unsigned int bitlen, const void *dout,
+ void *din, unsigned long flags)
+{
+ struct udevice *bus = dev->parent;
+ struct zynqmp_qspi_priv *priv = dev_get_priv(bus);
+
+ debug("%s: priv: 0x%08lx bitlen: %d dout: 0x%08lx ", __func__,
+ (unsigned long)priv, bitlen, (unsigned long)dout);
+ debug("din: 0x%08lx flags: 0x%lx\n", (unsigned long)din, flags);
+
+ priv->tx_buf = dout;
+ priv->rx_buf = din;
+ priv->len = bitlen / 8;
+
+ /*
+ * Festering sore.
+ * Assume that the beginning of a transfer with bits to
+ * transmit must contain a device command.
+ */
+ if (dout && flags & SPI_XFER_BEGIN)
+ priv->is_inst = 1;
+ else
+ priv->is_inst = 0;
+
+ if (flags & SPI_XFER_END)
+ priv->cs_change = 1;
+ else
+ priv->cs_change = 0;
+
+ zynqmp_qspi_transfer(priv);
+
+ return 0;
+}
+
+static const struct dm_spi_ops zynqmp_qspi_ops = {
+ .claim_bus = zynqmp_qspi_claim_bus,
+ .release_bus = zynqmp_qspi_release_bus,
+ .xfer = zynqmp_qspi_xfer,
+ .set_speed = zynqmp_qspi_set_speed,
+ .set_mode = zynqmp_qspi_set_mode,
+};
+
+static const struct udevice_id zynqmp_qspi_ids[] = {
+ { .compatible = "xlnx,zynqmp-qspi-1.0" },
+ { }
+};
+
+U_BOOT_DRIVER(zynqmp_qspi) = {
+ .name = "zynqmp_qspi",
+ .id = UCLASS_SPI,
+ .of_match = zynqmp_qspi_ids,
+ .ops = &zynqmp_qspi_ops,
+ .ofdata_to_platdata = zynqmp_qspi_ofdata_to_platdata,
+ .platdata_auto_alloc_size = sizeof(struct zynqmp_qspi_platdata),
+ .priv_auto_alloc_size = sizeof(struct zynqmp_qspi_priv),
+ .probe = zynqmp_qspi_probe,
+ .child_pre_probe = zynqmp_qspi_child_pre_probe,
+};
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
More information about the U-Boot
mailing list