[U-Boot] [PATCH] arm: zynq: Add initial support for Avnet MiniZed
Ibai Erkiaga
ibai.erkiaga-elorza at xilinx.com
Mon May 14 22:43:33 UTC 2018
Initial support for Avnet MiniZed board. Tested UART1 (serial console),
QSPI(Flash), SDHCI1 (eMMC), USB.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza at xilinx.com>
---
Changes for v3:
-dts formating refactor
-CONFIG_DISPLAY_CPUINFO removed from config
-CONFIG_OF_EMBED removed from config
Changes for v2:
-board model changed to use Avent prefix
-usb phy driver changed usb-no-xceiv
-removed gpio and intc binding
-fixed-partitions usage
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/zynq-minized.dts | 106 ++++++++++++++++++++++++++++++++++++++++
configs/zynq_minized_defconfig | 66 +++++++++++++++++++++++++
3 files changed, 173 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/dts/zynq-minized.dts
create mode 100644 configs/zynq_minized_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 7bec3d6..f7b33f9 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -130,6 +130,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-cc108.dtb \
zynq-cse-qspi-single.dtb \
zynq-microzed.dtb \
+ zynq-minized.dtb \
zynq-picozed.dtb \
zynq-syzygy-hub.dtb \
zynq-topic-miami.dtb \
diff --git a/arch/arm/dts/zynq-minized.dts b/arch/arm/dts/zynq-minized.dts
new file mode 100644
index 0000000..525921e
--- /dev/null
+++ b/arch/arm/dts/zynq-minized.dts
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Avnet MiniZed board
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Ibai Erkiaga <ibai.erkiaga-elorza at xilinx.com>
+ */
+
+/dts-v1/;
+#include "zynq-7000.dtsi"
+
+/ {
+ model = "Avnet Zynq MiniZed Development Board";
+ compatible = "avnet,minized", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &uart1;
+ serial1 = &uart0;
+ spi0 = &qspi;
+ mmc0 = &sdhci0;
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "";
+ stdout-path = "serial0:115200n8";
+ };
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&qspi {
+ status = "okay";
+ is-dual = <0>;
+ num-cs = <1>;
+ flash at 0 {
+ compatible = "micron,m25p128";
+ reg = <0x0>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <50000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition at 0 {
+ label = "boot";
+ reg = <0x0 0xff0000>;
+ };
+
+ partition at 270000 {
+ label = "kernel";
+ reg = <0x270000 0xd80000>;
+ };
+
+ partition at ff0000 {
+ label = "bootenv";
+ reg = <0xff0000 0x10000>;
+ };
+
+ partition at 1000000 {
+ label = "spare";
+ reg = <0x1000000 0x0>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
+ usb-reset = <&gpio0 7 0>; /* USB_RST_N-MIO7 */
+};
+
+&sdhci1 {
+ status = "okay";
+ non-removable;
+ bus-width = <4>;
+ max-frequency = <12000000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mmccard: mmccard at 0 {
+ compatible = "mmc-card";
+ reg = <0>;
+ broken-hpi;
+ };
+};
diff --git a/configs/zynq_minized_defconfig b/configs/zynq_minized_defconfig
new file mode 100644
index 0000000..8cf3215
--- /dev/null
+++ b/configs/zynq_minized_defconfig
@@ -0,0 +1,66 @@
+CONFIG_ARM=y
+CONFIG_ARCH_ZYNQ=y
+CONFIG_SYS_TEXT_BASE=0x4000000
+CONFIG_SPL=y
+CONFIG_SPL_STACK_R_ADDR=0x200000
+CONFIG_DEFAULT_DEVICE_TREE="zynq-minized"
+CONFIG_DEBUG_UART=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_BOOTCOMMAND="run $modeboot || run distro_bootcmd"
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_OS_BOOT=y
+CONFIG_SYS_PROMPT="Zynq> "
+CONFIG_CMD_THOR_DOWNLOAD=y
+CONFIG_CMD_DFU=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_FPGA_LOADBP=y
+CONFIG_CMD_FPGA_LOADFS=y
+CONFIG_CMD_FPGA_LOADMK=y
+CONFIG_CMD_FPGA_LOADP=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_DFU_MMC=y
+CONFIG_DFU_RAM=y
+CONFIG_FPGA_XILINX=y
+CONFIG_FPGA_ZYNQPL=y
+CONFIG_DM_GPIO=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ZYNQ=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_REALTEK=y
+CONFIG_PHY_XILINX=y
+CONFIG_ZYNQ_GEM=y
+CONFIG_DEBUG_UART_ZYNQ=y
+CONFIG_DEBUG_UART_BASE=0xe0001000
+CONFIG_DEBUG_UART_CLOCK=50000000
+CONFIG_ZYNQ_SERIAL=y
+CONFIG_ZYNQ_QSPI=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_ULPI_VIEWPORT=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Xilinx"
+CONFIG_USB_GADGET_VENDOR_NUM=0x03fd
+CONFIG_USB_GADGET_PRODUCT_NUM=0x0300
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_FUNCTION_THOR=y
--
1.7.1
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
More information about the U-Boot
mailing list