[U-Boot] [PULL] Please pull u-boot-imx
Stefano Babic
sbabic at denx.de
Thu May 17 17:08:37 UTC 2018
On 17/05/2018 18:33, Lukasz Majewski wrote:
> Hi Stefano, Tom,
>
Tom was not in CC, added
> On 17 May 2018 17:50, Stefano Babic <sbabic at denx.de> wrote:
>
> Hi Tom,
>
> please pull from u-boot-imx, thanks !
>
> The following changes since commit
> f2d0f5e7ab3b8a7b4bf6e2ac499b4867c701d52d:
>
> ARM: re-enable MVGBE for edminiv2 (2018-05-16 11:38:08 -0400)
>
> are available in the git repository at:
>
> git://www.denx.de/git/u-boot-imx.git master
>
> for you to fetch changes up to 2f5988533d5c447d7bda79b0d9719f84db9e1835:
>
> imx6: sabrelite: update defconfig to use distro defaults (2018-05-17
> 17:47:17 +0200)
>
> ----------------------------------------------------------------
> Guillaume GARDET (2):
> imx6: Convert sabrelite and nitrogen6x boards to distro boot
> support
> imx6: sabrelite: update defconfig to use distro defaults
>
> Ian Ray (6):
> board: ge: bx50v3: add winbond SPI NOR support
> board: ge: bx50v3: rename detect_baseboard function
> board: ge: bx50v3: fix display support for b{46}50v3
> board: ge: bx50v3: use VPD instead of compile-time checks
> board: ge: bx50v3: configure video arguments using VPD
> board: ge: bx50v3: remove redundant targets
>
> Lukasz Majewski (8):
> dts: imx53: Add gpio and i2c nodes to imx53.dtsi file
> dts: pinctrl: Provide IMX_PAD_SION definition for imx53 pinctrl
>
>
> Two above patches are correct.
>
> pmic: fsl: Provide some more definitions for MC34708 PMIC
> pmic: fsl: Define number of bytes sent at once by MC34708 PMIC
> pmic: dm: Provide *trans_len() callback for pmic-uclass
> pmic: dm: Rewrite pmic_reg_{read|write} and pmic_clrsetbits to
> support transmissions larger than 1 byte
> pmic: dm: Add support for MC34708 for PMIC DM
> arm: imx53: Add support for imx53 boards from K+P
>
>
> Stefano, Tom please drop above patches as they were superseded by v2 and
> v3 (after discussion with Simon).
I have just added the pmic patches due to the dependency in "arm: imx53:
Add support for imx53 boards from K+P", and I have not seen any change
request in them. I drop the series, Tom please wait, I will send a new
PR after.
>
> IMHO v3 is eligible for pulling:
> https://patchwork.ozlabs.org/patch/913670/
>
Should they flow into Jaehoon's tree instead of u-boot-imx ?
Best regards,
Stefano
> BR,
> Łukasz Majewski
>
> Magnus Lilja (2):
> mx31pdk: Convert CONFIG_MX31 flag to use Kconfig.
> mx31: Convert MX31_HCLK_FREQ and MX31_CLK32 to Kconfig.
>
> Nandor Han (2):
> board: ge: bx50v3: unify two switch statements
> board: ge: bx50v3: detect the monitor type by reading VPD earlier
>
> Peter Robinson (4):
> mx6 common: remove dangling comment
> mx7: remove empty ifndef statement
> mx6: Select CONFIG_MP with MX6_SMP
> mx6: remove duplicated BOUNCE_BUFFER defines
>
> Sebastian Reichel (1):
> ge: ppd: move CONFIG_ENV_IS_IN_MMC to defconfig
>
> arch/arm/Kconfig | 14 +++----
> arch/arm/dts/imx53-kp.dts | 135
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> arch/arm/dts/imx53-pinfunc.h | 1 +
> arch/arm/dts/imx53.dtsi | 101
> +++++++++++++++++++++++++++++++++++++++++++++++-
> arch/arm/include/asm/arch-mx31/clock.h | 8 ----
> arch/arm/mach-imx/mx3/Kconfig | 34
> +++++++++++++++++
> arch/arm/mach-imx/mx5/Kconfig | 12 ++++++
> arch/arm/mach-imx/mx6/Kconfig | 15 ++------
> board/ge/bx50v3/Kconfig | 2 +-
> board/ge/bx50v3/bx50v3.c | 71
> ++++++++++++++++++++++------------
> board/k+p/kp_imx53/Kconfig | 15 ++++++++
> board/k+p/kp_imx53/MAINTAINERS | 6 +++
> board/k+p/kp_imx53/Makefile | 8 ++++
> board/k+p/kp_imx53/kp_id_rev.c | 121
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> board/k+p/kp_imx53/kp_id_rev.h | 28
> ++++++++++++++
> board/k+p/kp_imx53/kp_imx53.c | 212
> +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> configs/ge_b650v3_defconfig | 43
> ---------------------
> configs/ge_b850v3_defconfig | 43
> ---------------------
> configs/{ge_b450v3_defconfig => ge_bx50v3_defconfig} | 4 +-
> configs/kp_imx53_defconfig | 40
> +++++++++++++++++++
> configs/mx31pdk_defconfig | 3 +-
> configs/mx53ppd_defconfig | 1 +
> configs/mx6qsabrelite_defconfig | 15 +++-----
> drivers/power/pmic/Kconfig | 7 ++++
> drivers/power/pmic/Makefile | 1 +
> drivers/power/pmic/mc34708.c | 103
> +++++++++++++++++++++++++++++++++++++++++++++++++
> drivers/power/pmic/pmic-uclass.c | 48
> +++++++++++++++++------
> include/configs/advantech_dms-ba16.h | 1 -
> include/configs/apalis_imx6.h | 1 -
> include/configs/colibri_imx6.h | 1 -
> include/configs/dh_imx6.h | 1 -
> include/configs/ge_bx50v3.h | 17 +--------
> include/configs/kp_imx53.h | 113
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++
> include/configs/kp_imx6q_tpc.h | 2 -
> include/configs/mx31pdk.h | 2 -
> include/configs/mx53ppd.h | 1 -
> include/configs/mx6_common.h | 3 --
> include/configs/mx7_common.h | 3 --
> include/configs/nitrogen6x.h | 179
> +++++++++++++++++++++----------------------------------------------------------------
> include/fsl_pmic.h | 41
> ++++++++++++++++++++
> include/power/pmic.h | 2 +
> 41 files changed, 1126 insertions(+), 332 deletions(-)
> create mode 100644 arch/arm/dts/imx53-kp.dts
> create mode 100644 arch/arm/mach-imx/mx3/Kconfig
> create mode 100644 board/k+p/kp_imx53/Kconfig
> create mode 100644 board/k+p/kp_imx53/MAINTAINERS
> create mode 100644 board/k+p/kp_imx53/Makefile
> create mode 100644 board/k+p/kp_imx53/kp_id_rev.c
> create mode 100644 board/k+p/kp_imx53/kp_id_rev.h
> create mode 100644 board/k+p/kp_imx53/kp_imx53.c
> delete mode 100644 configs/ge_b650v3_defconfig
> delete mode 100644 configs/ge_b850v3_defconfig
> rename configs/{ge_b450v3_defconfig => ge_bx50v3_defconfig} (93%)
> create mode 100644 configs/kp_imx53_defconfig
> create mode 100644 drivers/power/pmic/mc34708.c
> create mode 100644 include/configs/kp_imx53.h
>
> --
> =====================================================================
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
> =====================================================================
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot
>
>
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
More information about the U-Boot
mailing list