[U-Boot] [PATCH v6 02/11] phy: ti-pip3-phy: Add support for USB3 PHY

[Jean-Jacques Hiblot]

From: Vignesh R <vigneshr at ti.com>

Add support to handle USB3 PHYs present on AM57xx/DRA7xx SoCs. This is
needed to move AM57xx to DM_USB.

Signed-off-by: Vignesh R <vigneshr at ti.com>

Signed-off-by: Jean-Jacques Hiblot <jjhiblot at ti.com>
---

Changes in v6:
- ti-pipe3-phy: take PLL out of IDLE in pipe3_init(). The PLL may have
  been put into idle by pipe3_exit()

Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2:
- Add USB3 support to ti-pipe3-phy driver

 drivers/phy/ti-pipe3-phy.c | 32 ++++++++++++++++++++++++--------
 1 file changed, 24 insertions(+), 8 deletions(-)

diff --git a/drivers/phy/ti-pipe3-phy.c b/drivers/phy/ti-pipe3-phy.c
index b22bbaf..e7e78e3 100644
--- a/drivers/phy/ti-pipe3-phy.c
+++ b/drivers/phy/ti-pipe3-phy.c
@@ -141,7 +141,7 @@ static int omap_pipe3_dpll_program(struct omap_pipe3 *pipe3)
 	omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION1, val);
 
 	val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION2);
-	val &= ~PLL_SELFREQDCO_MASK;
+	val &= ~(PLL_SELFREQDCO_MASK | PLL_IDLE);
 	val |= dpll_params->freq << PLL_SELFREQDCO_SHIFT;
 	omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION2, val);
 
@@ -265,10 +265,13 @@ static int pipe3_exit(struct phy *phy)
 		return -EBUSY;
 	}
 
-	val = readl(pipe3->pll_reset_reg);
-	writel(val | SATA_PLL_SOFT_RESET, pipe3->pll_reset_reg);
-	mdelay(1);
-	writel(val & ~SATA_PLL_SOFT_RESET, pipe3->pll_reset_reg);
+	if (pipe3->pll_reset_reg) {
+		val = readl(pipe3->pll_reset_reg);
+		writel(val | SATA_PLL_SOFT_RESET, pipe3->pll_reset_reg);
+		mdelay(1);
+		writel(val & ~SATA_PLL_SOFT_RESET, pipe3->pll_reset_reg);
+	}
+
 	return 0;
 }
 
@@ -331,9 +334,11 @@ static int pipe3_phy_probe(struct udevice *dev)
 	if (!pipe3->power_reg)
 		return -EINVAL;
 
-	pipe3->pll_reset_reg = get_reg(dev, "syscon-pllreset");
-	if (!pipe3->pll_reset_reg)
-		return -EINVAL;
+	if (device_is_compatible(dev, "ti,phy-pipe3-sata")) {
+		pipe3->pll_reset_reg = get_reg(dev, "syscon-pllreset");
+		if (!pipe3->pll_reset_reg)
+			return -EINVAL;
+	}
 
 	pipe3->dpll_map = (struct pipe3_dpll_map *)dev_get_driver_data(dev);
 
@@ -350,8 +355,19 @@ static struct pipe3_dpll_map dpll_map_sata[] = {
 	{ },                                    /* Terminator */
 };
 
+static struct pipe3_dpll_map dpll_map_usb[] = {
+	{12000000, {1250, 5, 4, 20, 0} },	/* 12 MHz */
+	{16800000, {3125, 20, 4, 20, 0} },	/* 16.8 MHz */
+	{19200000, {1172, 8, 4, 20, 65537} },	/* 19.2 MHz */
+	{20000000, {1000, 7, 4, 10, 0} },	/* 20 MHz */
+	{26000000, {1250, 12, 4, 20, 0} },	/* 26 MHz */
+	{38400000, {3125, 47, 4, 20, 92843} },	/* 38.4 MHz */
+	{ },					/* Terminator */
+};
+
 static const struct udevice_id pipe3_phy_ids[] = {
 	{ .compatible = "ti,phy-pipe3-sata", .data = (ulong)&dpll_map_sata },
+	{ .compatible = "ti,omap-usb3", .data = (ulong)&dpll_map_usb},
 	{ }
 };
 
-- 
2.7.4