[U-Boot] [PATCH v6 11/11] board: ti: am57xx: remove USB platform code

[Jean-Jacques Hiblot]

Signed-off-by: Jean-Jacques Hiblot <jjhiblot at ti.com>

---

Changes in v6:
- Supports DM USB for peripherals
- Removed DTS changes that disabled USB1 on DRA7 because DM_USB_DEV is
  now supported

Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None

 board/ti/am57xx/board.c | 87 -------------------------------------------------
 1 file changed, 87 deletions(-)

diff --git a/board/ti/am57xx/board.c b/board/ti/am57xx/board.c
index 828a36c..00b8a79 100644
--- a/board/ti/am57xx/board.c
+++ b/board/ti/am57xx/board.c
@@ -883,93 +883,6 @@ int spl_start_uboot(void)
 }
 #endif
 
-#ifdef CONFIG_USB_DWC3
-static struct dwc3_device usb_otg_ss2 = {
-	.maximum_speed = USB_SPEED_HIGH,
-	.base = DRA7_USB_OTG_SS2_BASE,
-	.tx_fifo_resize = false,
-	.index = 1,
-};
-
-static struct dwc3_omap_device usb_otg_ss2_glue = {
-	.base = (void *)DRA7_USB_OTG_SS2_GLUE_BASE,
-	.utmi_mode = DWC3_OMAP_UTMI_MODE_SW,
-	.index = 1,
-};
-
-static struct ti_usb_phy_device usb_phy2_device = {
-	.usb2_phy_power = (void *)DRA7_USB2_PHY2_POWER,
-	.index = 1,
-};
-
-int usb_gadget_handle_interrupts(int index)
-{
-	u32 status;
-
-	status = dwc3_omap_uboot_interrupt_status(index);
-	if (status)
-		dwc3_uboot_handle_interrupt(index);
-
-	return 0;
-}
-#endif /* CONFIG_USB_DWC3 */
-
-#if defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP)
-int board_usb_init(int index, enum usb_init_type init)
-{
-	enable_usb_clocks(index);
-	switch (index) {
-	case 0:
-		if (init == USB_INIT_DEVICE) {
-			printf("port %d can't be used as device\n", index);
-			disable_usb_clocks(index);
-			return -EINVAL;
-		}
-		break;
-	case 1:
-		if (init == USB_INIT_DEVICE) {
-#ifdef CONFIG_USB_DWC3
-			usb_otg_ss2.dr_mode = USB_DR_MODE_PERIPHERAL;
-			usb_otg_ss2_glue.vbus_id_status = OMAP_DWC3_VBUS_VALID;
-			ti_usb_phy_uboot_init(&usb_phy2_device);
-			dwc3_omap_uboot_init(&usb_otg_ss2_glue);
-			dwc3_uboot_init(&usb_otg_ss2);
-#endif
-		} else {
-			printf("port %d can't be used as host\n", index);
-			disable_usb_clocks(index);
-			return -EINVAL;
-		}
-
-		break;
-	default:
-		printf("Invalid Controller Index\n");
-	}
-
-	return 0;
-}
-
-int board_usb_cleanup(int index, enum usb_init_type init)
-{
-#ifdef CONFIG_USB_DWC3
-	switch (index) {
-	case 0:
-	case 1:
-		if (init == USB_INIT_DEVICE) {
-			ti_usb_phy_uboot_exit(index);
-			dwc3_uboot_exit(index);
-			dwc3_omap_uboot_exit(index);
-		}
-		break;
-	default:
-		printf("Invalid Controller Index\n");
-	}
-#endif
-	disable_usb_clocks(index);
-	return 0;
-}
-#endif /* defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP) */
-
 #ifdef CONFIG_DRIVER_TI_CPSW
 
 /* Delay value to add to calibrated value */
-- 
2.7.4