[U-Boot] [PATCH 22/41] serial: lpuart: Enable RX and TX FIFO

[Peng Fan]

From: Ye Li <ye.li at nxp.com>

Enable the RX and TX FIFO in LPUART driver to avoid the input lost
during u-boot boot up.

Signed-off-by: Ye Li <ye.li at nxp.com>
Acked-by: Peng Fan <peng.fan at nxp.com>
---
 drivers/serial/serial_lpuart.c | 33 ++++++++++++++++++++++++++-------
 1 file changed, 26 insertions(+), 7 deletions(-)

diff --git a/drivers/serial/serial_lpuart.c b/drivers/serial/serial_lpuart.c
index a5a2f65c77..e99a49d0d9 100644
--- a/drivers/serial/serial_lpuart.c
+++ b/drivers/serial/serial_lpuart.c
@@ -40,6 +40,12 @@
 #define CTRL_TE		(1 << 19)
 #define CTRL_RE		(1 << 18)
 
+#define FIFO_RXFLUSH		(1 << 14)
+#define FIFO_TXFLUSH		(1 << 15)
+#define FIFO_TXSIZE_MASK	0x70
+#define FIFO_TXSIZE_OFF	4
+#define FIFO_RXSIZE_MASK	0x7
+#define FIFO_RXSIZE_OFF	0
 #define FIFO_TXFE		0x80
 #ifdef CONFIG_IMX8
 #define FIFO_RXFE		0x08
@@ -47,7 +53,7 @@
 #define FIFO_RXFE		0x40
 #endif
 
-#define WATER_TXWATER_OFF	1
+#define WATER_TXWATER_OFF	0
 #define WATER_RXWATER_OFF	16
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -318,15 +324,28 @@ static int _lpuart32_serial_tstc(struct lpuart_serial_platdata *plat)
 static int _lpuart32_serial_init(struct lpuart_serial_platdata *plat)
 {
 	struct lpuart_fsl_reg32 *base = (struct lpuart_fsl_reg32 *)plat->reg;
-	u32 ctrl;
+	u32 val, tx_fifo_size;
 
-	lpuart_read32(plat->flags, &base->ctrl, &ctrl);
-	ctrl &= ~CTRL_RE;
-	ctrl &= ~CTRL_TE;
-	lpuart_write32(plat->flags, &base->ctrl, ctrl);
+	lpuart_read32(plat->flags, &base->ctrl, &val);
+	val &= ~CTRL_RE;
+	val &= ~CTRL_TE;
+	lpuart_write32(plat->flags, &base->ctrl, val);
 
 	lpuart_write32(plat->flags, &base->modir, 0);
-	lpuart_write32(plat->flags, &base->fifo, ~(FIFO_TXFE | FIFO_RXFE));
+
+	lpuart_read32(plat->flags, &base->fifo, &val);
+	tx_fifo_size = (val & FIFO_TXSIZE_MASK) >> FIFO_TXSIZE_OFF;
+	/* Set the TX water to half of FIFO size */
+	if (tx_fifo_size > 1)
+		tx_fifo_size = tx_fifo_size >> 1;
+
+	/* Set RX water to 0, to be triggered by any receive data */
+	lpuart_write32(plat->flags, &base->water,
+		       (tx_fifo_size << WATER_TXWATER_OFF));
+
+	/* Enable TX and RX FIFO */
+	val |= (FIFO_TXFE | FIFO_RXFE | FIFO_TXFLUSH | FIFO_RXFLUSH);
+	lpuart_write32(plat->flags, &base->fifo, val);
 
 	lpuart_write32(plat->flags, &base->match, 0);
 
-- 
2.14.1