[U-Boot] [PATCH v7 10/11] board: ti: dra7-evm: remove USB platform code

[Jean-Jacques Hiblot]

Signed-off-by: Jean-Jacques Hiblot <jjhiblot at ti.com>
---

Changes in v7: None
Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None

 board/ti/dra7xx/evm.c | 105 --------------------------------------------------
 1 file changed, 105 deletions(-)

diff --git a/board/ti/dra7xx/evm.c b/board/ti/dra7xx/evm.c
index ebfe316..10fe494 100644
--- a/board/ti/dra7xx/evm.c
+++ b/board/ti/dra7xx/evm.c
@@ -915,111 +915,6 @@ const struct mmc_platform_fixups *platform_fixups_mmc(uint32_t addr)
 }
 #endif
 
-#if defined(CONFIG_USB_DWC3) && \
-    !(defined(CONFIG_DM_USB) && defined(CONFIG_DM_USB_DEV))
-static struct dwc3_device usb_otg_ss1 = {
-	.maximum_speed = USB_SPEED_SUPER,
-	.base = DRA7_USB_OTG_SS1_BASE,
-	.tx_fifo_resize = false,
-	.index = 0,
-};
-
-static struct dwc3_omap_device usb_otg_ss1_glue = {
-	.base = (void *)DRA7_USB_OTG_SS1_GLUE_BASE,
-	.utmi_mode = DWC3_OMAP_UTMI_MODE_SW,
-	.index = 0,
-};
-
-static struct ti_usb_phy_device usb_phy1_device = {
-	.pll_ctrl_base = (void *)DRA7_USB3_PHY1_PLL_CTRL,
-	.usb2_phy_power = (void *)DRA7_USB2_PHY1_POWER,
-	.usb3_phy_power = (void *)DRA7_USB3_PHY1_POWER,
-	.index = 0,
-};
-
-static struct dwc3_device usb_otg_ss2 = {
-	.maximum_speed = USB_SPEED_SUPER,
-	.base = DRA7_USB_OTG_SS2_BASE,
-	.tx_fifo_resize = false,
-	.index = 1,
-};
-
-static struct dwc3_omap_device usb_otg_ss2_glue = {
-	.base = (void *)DRA7_USB_OTG_SS2_GLUE_BASE,
-	.utmi_mode = DWC3_OMAP_UTMI_MODE_SW,
-	.index = 1,
-};
-
-static struct ti_usb_phy_device usb_phy2_device = {
-	.usb2_phy_power = (void *)DRA7_USB2_PHY2_POWER,
-	.index = 1,
-};
-
-int board_usb_init(int index, enum usb_init_type init)
-{
-	enable_usb_clocks(index);
-	switch (index) {
-	case 0:
-		if (init == USB_INIT_DEVICE) {
-			usb_otg_ss1.dr_mode = USB_DR_MODE_PERIPHERAL;
-			usb_otg_ss1_glue.vbus_id_status = OMAP_DWC3_VBUS_VALID;
-		} else {
-			usb_otg_ss1.dr_mode = USB_DR_MODE_HOST;
-			usb_otg_ss1_glue.vbus_id_status = OMAP_DWC3_ID_GROUND;
-		}
-
-		ti_usb_phy_uboot_init(&usb_phy1_device);
-		dwc3_omap_uboot_init(&usb_otg_ss1_glue);
-		dwc3_uboot_init(&usb_otg_ss1);
-		break;
-	case 1:
-		if (init == USB_INIT_DEVICE) {
-			usb_otg_ss2.dr_mode = USB_DR_MODE_PERIPHERAL;
-			usb_otg_ss2_glue.vbus_id_status = OMAP_DWC3_VBUS_VALID;
-		} else {
-			usb_otg_ss2.dr_mode = USB_DR_MODE_HOST;
-			usb_otg_ss2_glue.vbus_id_status = OMAP_DWC3_ID_GROUND;
-		}
-
-		ti_usb_phy_uboot_init(&usb_phy2_device);
-		dwc3_omap_uboot_init(&usb_otg_ss2_glue);
-		dwc3_uboot_init(&usb_otg_ss2);
-		break;
-	default:
-		printf("Invalid Controller Index\n");
-	}
-
-	return 0;
-}
-
-int board_usb_cleanup(int index, enum usb_init_type init)
-{
-	switch (index) {
-	case 0:
-	case 1:
-		ti_usb_phy_uboot_exit(index);
-		dwc3_uboot_exit(index);
-		dwc3_omap_uboot_exit(index);
-		break;
-	default:
-		printf("Invalid Controller Index\n");
-	}
-	disable_usb_clocks(index);
-	return 0;
-}
-
-int usb_gadget_handle_interrupts(int index)
-{
-	u32 status;
-
-	status = dwc3_omap_uboot_interrupt_status(index);
-	if (status)
-		dwc3_uboot_handle_interrupt(index);
-
-	return 0;
-}
-#endif
-
 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_OS_BOOT)
 int spl_start_uboot(void)
 {
-- 
2.7.4