[U-Boot] [PATCH v4 0/5] Add support for Pinebook

[Dennis Gilmore]

I have tested the series on my pinebook on top of git commit
99431c1c21685fe63d46b6eac995b78ce9adce0a

I am not sure if video is expected to work or not, in my case it does
not work. 

U-Boot SPL 2018.11-rc3-00027-g77a46c3a3c (Nov 03 2018 - 13:42:47 -0500)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE:  BL31: v1.6(release):
NOTICE:  BL31: Built : 09:10:17, Sep 23 2018
NOTICE:  BL31: Detected Allwinner A64/H64/R18 SoC (1689)
NOTICE:  BL31: STUB PMIC setup code called


U-Boot 2018.11-rc3-00027-g77a46c3a3c (Nov 03 2018 - 13:42:47 -0500)
Allwinner Technology

CPU:   Allwinner A64 (SUN50I)
Model: Pinebook
DRAM:  2 GiB
MMC:   SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
Loading Environment from FAT... *** Warning - bad CRC, using default
environment

Warning: HDMI PHY init timeout!
Warning: HDMI PHY init timeout!
In:    serial
Out:   serial
Err:   serial

u-boot however works fine and the system is able to boot and the
correct dtb is loaded.

Tested-by: Dennis Gilmore <dennis at ausil.us>

El mar, 30-10-2018 a las 14:36 -0700, Vagrant Cascadian escribió:
> Tested series applied to u-boot 2018.11-rc3 on pinebook, both with
> reboot and cold boot.
> 
> Thanks for all the work on it!
> 
> Tested-by: Vagrant Cascadian <vagrant at debian.org>
> 
> On 2018-10-28, Vasily Khoruzhick wrote:
> > This series adds support for the Pinebook, an allwinner A64 laptop
> > produced by Pine64. It also syncs sun50i-a64.dtsi with linux,
> > adds support for mmc delay calibration, R_I2C controller,
> > and addresses the issue with activating video bridge when any of
> > GPIOs is missing.
> > 
> > v2: - sync sun50i-a64.dtsi with linux instead of adding missing
> > nodes
> >     - take sun50i-a64-pinebook.dts from linux
> >     - don't introduce new Kconfig for A64 MMC calibration
> >     - improve code in video bridge uclass to check for presensce of
> >       GPIO instead of ingoring EINVAL errors
> > v3: - enable calibration for H6 as well
> >     - init ret variable in video_bridge_set_active()
> >     - fix order of dts files Makefile
> >     - split anx6345 binding into sun50i-a64-pinebook-u-boot.dts
> >     - drop speaker_amp node from pinebook dts
> >     - drop unnecessary options from defconfig
> > v4: - sync device tree files with linux-next
> > 
> > Vasily Khoruzhick (5):
> >   mmc: sunxi: add support for automatic delay calibration
> >   dm: video: bridge: don't fail to activate bridge if reset or
> > sleep
> >     GPIO is missing
> >   sunxi: DT: A64: update device tree files for Allwinner A64 SoC
> >   sun50i: A64: add support for R_I2C controller
> >   sunxi: DT: add support for Pinebook
> > 
> >  arch/arm/dts/Makefile                        |   1 +
> >  arch/arm/dts/sun50i-a64-amarula-relic.dts    | 168 +++++++++-
> >  arch/arm/dts/sun50i-a64-bananapi-m64.dts     |  34 +-
> >  arch/arm/dts/sun50i-a64-nanopi-a64.dts       |  89 +++++-
> >  arch/arm/dts/sun50i-a64-olinuxino.dts        | 103 +++++-
> >  arch/arm/dts/sun50i-a64-orangepi-win.dts     | 179 ++++++++++-
> >  arch/arm/dts/sun50i-a64-pine64.dts           |  32 +-
> >  arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi |  15 +
> >  arch/arm/dts/sun50i-a64-pinebook.dts         | 294
> > +++++++++++++++++
> >  arch/arm/dts/sun50i-a64-sopine-baseboard.dts |  32 +-
> >  arch/arm/dts/sun50i-a64-sopine.dtsi          |  15 +
> >  arch/arm/dts/sun50i-a64.dtsi                 | 313
> > +++++++++++++++++--
> >  arch/arm/include/asm/arch-sunxi/gpio.h       |   1 +
> >  arch/arm/include/asm/arch-sunxi/mmc.h        |   6 +-
> >  arch/arm/mach-sunxi/Kconfig                  |   1 +
> >  board/sunxi/board.c                          |   6 +
> >  configs/pinebook_defconfig                   |  22 ++
> >  drivers/mmc/sunxi_mmc.c                      |  21 +-
> >  drivers/video/bridge/video-bridge-uclass.c   |  16 +-
> >  19 files changed, 1296 insertions(+), 52 deletions(-)
> >  create mode 100644 arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi
> >  create mode 100644 arch/arm/dts/sun50i-a64-pinebook.dts
> >  create mode 100644 configs/pinebook_defconfig
> > 
> > -- 
> > 2.19.1
> 
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot