[U-Boot] [PATCH v4 0/5] Add support for Pinebook
Vasily Khoruzhick
anarsoul at gmail.com
Sat Nov 3 20:18:37 UTC 2018
Video is supposed to work, but you need ATF from Andre to enable LCD power:
https://github.com/apritzel/arm-trusted-firmware/
On Sat, Nov 3, 2018 at 11:53 AM Dennis Gilmore <dennis at ausil.us> wrote:
>
> I have tested the series on my pinebook on top of git commit
> 99431c1c21685fe63d46b6eac995b78ce9adce0a
>
> I am not sure if video is expected to work or not, in my case it does
> not work.
>
> U-Boot SPL 2018.11-rc3-00027-g77a46c3a3c (Nov 03 2018 - 13:42:47 -0500)
> DRAM: 2048 MiB
> Trying to boot from MMC1
> NOTICE: BL31: v1.6(release):
> NOTICE: BL31: Built : 09:10:17, Sep 23 2018
> NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689)
> NOTICE: BL31: STUB PMIC setup code called
>
>
> U-Boot 2018.11-rc3-00027-g77a46c3a3c (Nov 03 2018 - 13:42:47 -0500)
> Allwinner Technology
>
> CPU: Allwinner A64 (SUN50I)
> Model: Pinebook
> DRAM: 2 GiB
> MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
> Loading Environment from FAT... *** Warning - bad CRC, using default
> environment
>
> Warning: HDMI PHY init timeout!
> Warning: HDMI PHY init timeout!
> In: serial
> Out: serial
> Err: serial
>
> u-boot however works fine and the system is able to boot and the
> correct dtb is loaded.
>
> Tested-by: Dennis Gilmore <dennis at ausil.us>
>
> El mar, 30-10-2018 a las 14:36 -0700, Vagrant Cascadian escribió:
> > Tested series applied to u-boot 2018.11-rc3 on pinebook, both with
> > reboot and cold boot.
> >
> > Thanks for all the work on it!
> >
> > Tested-by: Vagrant Cascadian <vagrant at debian.org>
> >
> > On 2018-10-28, Vasily Khoruzhick wrote:
> > > This series adds support for the Pinebook, an allwinner A64 laptop
> > > produced by Pine64. It also syncs sun50i-a64.dtsi with linux,
> > > adds support for mmc delay calibration, R_I2C controller,
> > > and addresses the issue with activating video bridge when any of
> > > GPIOs is missing.
> > >
> > > v2: - sync sun50i-a64.dtsi with linux instead of adding missing
> > > nodes
> > > - take sun50i-a64-pinebook.dts from linux
> > > - don't introduce new Kconfig for A64 MMC calibration
> > > - improve code in video bridge uclass to check for presensce of
> > > GPIO instead of ingoring EINVAL errors
> > > v3: - enable calibration for H6 as well
> > > - init ret variable in video_bridge_set_active()
> > > - fix order of dts files Makefile
> > > - split anx6345 binding into sun50i-a64-pinebook-u-boot.dts
> > > - drop speaker_amp node from pinebook dts
> > > - drop unnecessary options from defconfig
> > > v4: - sync device tree files with linux-next
> > >
> > > Vasily Khoruzhick (5):
> > > mmc: sunxi: add support for automatic delay calibration
> > > dm: video: bridge: don't fail to activate bridge if reset or
> > > sleep
> > > GPIO is missing
> > > sunxi: DT: A64: update device tree files for Allwinner A64 SoC
> > > sun50i: A64: add support for R_I2C controller
> > > sunxi: DT: add support for Pinebook
> > >
> > > arch/arm/dts/Makefile | 1 +
> > > arch/arm/dts/sun50i-a64-amarula-relic.dts | 168 +++++++++-
> > > arch/arm/dts/sun50i-a64-bananapi-m64.dts | 34 +-
> > > arch/arm/dts/sun50i-a64-nanopi-a64.dts | 89 +++++-
> > > arch/arm/dts/sun50i-a64-olinuxino.dts | 103 +++++-
> > > arch/arm/dts/sun50i-a64-orangepi-win.dts | 179 ++++++++++-
> > > arch/arm/dts/sun50i-a64-pine64.dts | 32 +-
> > > arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi | 15 +
> > > arch/arm/dts/sun50i-a64-pinebook.dts | 294
> > > +++++++++++++++++
> > > arch/arm/dts/sun50i-a64-sopine-baseboard.dts | 32 +-
> > > arch/arm/dts/sun50i-a64-sopine.dtsi | 15 +
> > > arch/arm/dts/sun50i-a64.dtsi | 313
> > > +++++++++++++++++--
> > > arch/arm/include/asm/arch-sunxi/gpio.h | 1 +
> > > arch/arm/include/asm/arch-sunxi/mmc.h | 6 +-
> > > arch/arm/mach-sunxi/Kconfig | 1 +
> > > board/sunxi/board.c | 6 +
> > > configs/pinebook_defconfig | 22 ++
> > > drivers/mmc/sunxi_mmc.c | 21 +-
> > > drivers/video/bridge/video-bridge-uclass.c | 16 +-
> > > 19 files changed, 1296 insertions(+), 52 deletions(-)
> > > create mode 100644 arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi
> > > create mode 100644 arch/arm/dts/sun50i-a64-pinebook.dts
> > > create mode 100644 configs/pinebook_defconfig
> > >
> > > --
> > > 2.19.1
> >
> > _______________________________________________
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > https://lists.denx.de/listinfo/u-boot
>
More information about the U-Boot
mailing list