[U-Boot] [PATCH 3/4] configs: wb45n_defconfig: Remove SPL

[Ben Whitten]

Just compiled with the bootlin toolchain
' armv5-eabi--musl--stable-2018.02-2' from within buildroot
and it looks like an image is produced within size.
text	   data	    bss	    dec	    hex	filename
  17965	   1180	   4480	  23625	   5c49	u-boot-spl

It looks like the assertion calculates the assertion
incorrectly, will comment on that patch.

Ben
> -----Original Message-----
> From: U-Boot [mailto:u-boot-bounces at lists.denx.de] On
> Behalf Of Ben Whitten
> Sent: 19 November 2018 10:30
> To: Eugen.Hristev at microchip.com; u-boot at lists.denx.de
> Cc: Nicolas.Ferre at microchip.com
> Subject: Re: [U-Boot] [PATCH 3/4] configs:
> wb45n_defconfig: Remove SPL
> 
> Hi,
> 
> A shame as these boards only really need to start NAND and
> boot uboot proper. Out of interest how much is it over in
> the
> builder?
> 
> If SPL can't be shrunk any further then fair enough and;
> Acked-by: Ben Whitten <ben.whitten at lairdtech.com>
> 
> Thanks,
> Ben
> 
> > -----Original Message-----
> > From: U-Boot [mailto:u-boot-bounces at lists.denx.de] On
> > Behalf Of Eugen.Hristev at microchip.com
> > Sent: 19 November 2018 08:23
> > To: u-boot at lists.denx.de
> > Cc: Nicolas.Ferre at microchip.com
> > Subject: [U-Boot] [PATCH 3/4] configs: wb45n_defconfig:
> > Remove SPL
> >
> > Due the size of SPL being too big, remove the SPL support.
> > ---8<---
> > arm-linux-gnueabi-ld: SPL image too big
> > --->8---
> >
> > Signed-off-by: Eugen Hristev
> > <eugen.hristev at microchip.com>
> > ---
> >  configs/wb45n_defconfig | 6 ------
> >  1 file changed, 6 deletions(-)
> >
> > diff --git a/configs/wb45n_defconfig
> > b/configs/wb45n_defconfig
> > index 9d881e5..aef4e75 100644
> > --- a/configs/wb45n_defconfig
> > +++ b/configs/wb45n_defconfig
> > @@ -3,17 +3,11 @@ CONFIG_SYS_THUMB_BUILD=y
> >  CONFIG_ARCH_AT91=y
> >  CONFIG_SYS_TEXT_BASE=0x23f00000
> >  CONFIG_TARGET_WB45N=y
> > -CONFIG_SPL_GPIO_SUPPORT=y
> > -CONFIG_SPL_LIBCOMMON_SUPPORT=y
> > -CONFIG_SPL_LIBGENERIC_SUPPORT=y
> > -CONFIG_SPL_SERIAL_SUPPORT=y
> > -CONFIG_SPL=y
> >  CONFIG_NR_DRAM_BANKS=1
> >  CONFIG_FIT=y
> >
> >
> CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9X5,SYS_USE_NA
> > NDFLASH"
> >  CONFIG_BOOTDELAY=3
> >  CONFIG_BOARD_EARLY_INIT_F=y
> > -CONFIG_SPL_NAND_SUPPORT=y
> >  CONFIG_HUSH_PARSER=y
> >  CONFIG_CMD_BOOTZ=y
> >  CONFIG_CMD_MEMTEST=y
> > --
> > 2.7.4
> >
> >
> ______________________________________________
> > _
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > https://lists.denx.de/listinfo/u-boot
> ______________________________________________
> _
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot