[U-Boot] [PATCH 12/93] arm: Remove tbs2910 board
Simon Glass
sjg at chromium.org
Mon Nov 19 15:52:52 UTC 2018
This board has not been converted to CONFIG_DM_BLK by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg at chromium.org>
---
arch/arm/mach-imx/mx6/Kconfig | 1 -
board/tbs/tbs2910/Kconfig | 18 --
board/tbs/tbs2910/MAINTAINERS | 6 -
board/tbs/tbs2910/Makefile | 5 -
board/tbs/tbs2910/tbs2910.c | 454 ----------------------------------
board/tbs/tbs2910/tbs2910.cfg | 114 ---------
configs/tbs2910_defconfig | 58 -----
include/configs/tbs2910.h | 158 ------------
8 files changed, 814 deletions(-)
delete mode 100644 board/tbs/tbs2910/Kconfig
delete mode 100644 board/tbs/tbs2910/MAINTAINERS
delete mode 100644 board/tbs/tbs2910/Makefile
delete mode 100644 board/tbs/tbs2910/tbs2910.c
delete mode 100644 board/tbs/tbs2910/tbs2910.cfg
delete mode 100644 configs/tbs2910_defconfig
delete mode 100644 include/configs/tbs2910.h
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index 9ed827067b1..2b96c55b61b 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -559,7 +559,6 @@ source "board/logicpd/imx6/Kconfig"
source "board/seco/Kconfig"
source "board/solidrun/mx6cuboxi/Kconfig"
source "board/technexion/pico-imx6ul/Kconfig"
-source "board/tbs/tbs2910/Kconfig"
source "board/tqc/tqma6/Kconfig"
source "board/toradex/apalis_imx6/Kconfig"
source "board/toradex/colibri-imx6ull/Kconfig"
diff --git a/board/tbs/tbs2910/Kconfig b/board/tbs/tbs2910/Kconfig
deleted file mode 100644
index 2e5e1d492a5..00000000000
--- a/board/tbs/tbs2910/Kconfig
+++ /dev/null
@@ -1,18 +0,0 @@
-if TARGET_TBS2910
-
-config SYS_BOARD
- default "tbs2910"
-
-config SYS_VENDOR
- default "tbs"
-
-config SYS_CONFIG_NAME
- default "tbs2910"
-
-config MX6Q
- default y
-
-config IMX_CONFIG
- default "board/tbs/tbs2910/tbs2910.cfg"
-
-endif
diff --git a/board/tbs/tbs2910/MAINTAINERS b/board/tbs/tbs2910/MAINTAINERS
deleted file mode 100644
index bf176553d24..00000000000
--- a/board/tbs/tbs2910/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-TBS2910 BOARD
-M: Soeren Moch <smoch at web.de>
-S: Maintained
-F: board/tbs/tbs2910/
-F: configs/tbs2910_defconfig
-F: include/configs/tbs2910.h
diff --git a/board/tbs/tbs2910/Makefile b/board/tbs/tbs2910/Makefile
deleted file mode 100644
index 78f4a3eecd4..00000000000
--- a/board/tbs/tbs2910/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2014 Soeren Moch <smoch at web.de>
-
-obj-y := tbs2910.o
diff --git a/board/tbs/tbs2910/tbs2910.c b/board/tbs/tbs2910/tbs2910.c
deleted file mode 100644
index ecb45f208d0..00000000000
--- a/board/tbs/tbs2910/tbs2910.c
+++ /dev/null
@@ -1,454 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2014 Soeren Moch <smoch at web.de>
- */
-
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <linux/errno.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/sata.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/video.h>
-#include <mmc.h>
-#include <fsl_esdhc.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <asm/arch/mxc_hdmi.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/io.h>
-#include <asm/arch/sys_proto.h>
-#include <i2c.h>
-DECLARE_GLOBAL_DATA_PTR;
-
-#define WEAK_PULLUP (PAD_CTL_PUS_47K_UP | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_SRE_SLOW)
-
-#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
-#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
-
-#ifdef CONFIG_SYS_I2C
-/* I2C1, SGTL5000 */
-static struct i2c_pads_info i2c_pad_info0 = {
- .scl = {
- .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
- .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD,
- .gp = IMX_GPIO_NR(5, 27)
- },
- .sda = {
- .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD,
- .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD,
- .gp = IMX_GPIO_NR(5, 26)
- }
-};
-
-/* I2C2 HDMI */
-static struct i2c_pads_info i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
- .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
- .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-/* I2C3, CON11, DS1307, PCIe_SMB */
-static struct i2c_pads_info i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD,
- .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD,
- .gp = IMX_GPIO_NR(1, 3)
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
- .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
- .gp = IMX_GPIO_NR(1, 6)
- }
-};
-#endif /* CONFIG_SYS_I2C */
-
-static iomux_v3_cfg_t const uart1_pads[] = {
- MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const uart2_pads[] = {
- MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- /* AR8035 PHY Reset */
- MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const pcie_pads[] = {
- /* W_DISABLE# */
- MX6_PAD_KEY_COL4__GPIO4_IO14 | MUX_PAD_CTRL(WEAK_PULLUP),
- /* PERST# */
- MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-int dram_init(void)
-{
- gd->ram_size = 2048ul * 1024 * 1024;
- return 0;
-}
-
-static void setup_iomux_enet(void)
-{
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-
- /* Reset AR8035 PHY */
- gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
- udelay(500);
- gpio_set_value(IMX_GPIO_NR(1, 25), 1);
-}
-
-static void setup_pcie(void)
-{
- imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
-}
-
-static void setup_iomux_uart(void)
-{
- imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
- imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
-}
-
-#ifdef CONFIG_FSL_ESDHC
-static iomux_v3_cfg_t const usdhc2_pads[] = {
- MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-static iomux_v3_cfg_t const usdhc3_pads[] = {
- MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-static iomux_v3_cfg_t const usdhc4_pads[] = {
- MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-
-static struct fsl_esdhc_cfg usdhc_cfg[3] = {
- {USDHC2_BASE_ADDR},
- {USDHC3_BASE_ADDR},
- {USDHC4_BASE_ADDR},
-};
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 2)
-#define USDHC3_CD_GPIO IMX_GPIO_NR(2, 0)
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC2_BASE_ADDR:
- ret = !gpio_get_value(USDHC2_CD_GPIO);
- break;
- case USDHC3_BASE_ADDR:
- ret = !gpio_get_value(USDHC3_CD_GPIO);
- break;
- case USDHC4_BASE_ADDR:
- ret = 1; /* eMMC/uSDHC4 is always present */
- break;
- }
- return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
- /*
- * (U-Boot device node) (Physical Port)
- * mmc0 SD2
- * mmc1 SD3
- * mmc2 eMMC
- */
- int i, ret;
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- switch (i) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(
- usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
- gpio_direction_input(USDHC2_CD_GPIO);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- break;
- case 1:
- imx_iomux_v3_setup_multiple_pads(
- usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
- gpio_direction_input(USDHC3_CD_GPIO);
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- break;
- case 2:
- imx_iomux_v3_setup_multiple_pads(
- usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
- usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- break;
- default:
- printf("Warning: you configured more USDHC controllers"
- "(%d) then supported by the board (%d)\n",
- i + 1, CONFIG_SYS_FSL_USDHC_NUM);
- return -EINVAL;
- }
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- if (ret)
- return ret;
- }
- return 0;
-}
-
-/* set environment device to boot device when booting from SD */
-int board_mmc_get_env_dev(int devno)
-{
- return devno - 1;
-}
-
-int board_mmc_get_env_part(int devno)
-{
- return (devno == 3) ? 1 : 0; /* part 0 for SD2 / SD3, part 1 for eMMC */
-}
-#endif /* CONFIG_FSL_ESDHC */
-
-#ifdef CONFIG_VIDEO_IPUV3
-static void do_enable_hdmi(struct display_info_t const *dev)
-{
- imx_enable_hdmi_phy();
-}
-
-struct display_info_t const displays[] = {{
- .bus = -1,
- .addr = 0,
- .pixfmt = IPU_PIX_FMT_RGB24,
- .detect = detect_hdmi,
- .enable = do_enable_hdmi,
- .mode = {
- .name = "HDMI",
- /* 1024x768 at 60Hz (VESA)*/
- .refresh = 60,
- .xres = 1024,
- .yres = 768,
- .pixclock = 15384,
- .left_margin = 160,
- .right_margin = 24,
- .upper_margin = 29,
- .lower_margin = 3,
- .hsync_len = 136,
- .vsync_len = 6,
- .sync = FB_SYNC_EXT,
- .vmode = FB_VMODE_NONINTERLACED
-} } };
-size_t display_count = ARRAY_SIZE(displays);
-
-static void setup_display(void)
-{
- struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
- int reg;
- s32 timeout = 100000;
-
- enable_ipu_clock();
- imx_setup_hdmi();
-
- /* set video pll to 455MHz (24MHz * (37+11/12) / 2) */
- reg = readl(&ccm->analog_pll_video);
- reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN;
- writel(reg, &ccm->analog_pll_video);
-
- reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
- reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(37);
- reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
- reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1);
- writel(reg, &ccm->analog_pll_video);
-
- writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
- writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
-
- reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
- writel(reg, &ccm->analog_pll_video);
-
- while (timeout--)
- if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
- break;
- if (timeout < 0)
- printf("Warning: video pll lock timeout!\n");
-
- reg = readl(&ccm->analog_pll_video);
- reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
- reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
- writel(reg, &ccm->analog_pll_video);
-
- /* gate ipu1_di0_clk */
- reg = readl(&ccm->CCGR3);
- reg &= ~MXC_CCM_CCGR3_LDB_DI0_MASK;
- writel(reg, &ccm->CCGR3);
-
- /* select video_pll clock / 7 for ipu1_di0_clk -> 65MHz pixclock */
- reg = readl(&ccm->chsccdr);
- reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK |
- MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK |
- MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
- reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET) |
- (6 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) |
- (0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
- writel(reg, &ccm->chsccdr);
-
- /* enable ipu1_di0_clk */
- reg = readl(&ccm->CCGR3);
- reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
- writel(reg, &ccm->CCGR3);
-}
-#endif /* CONFIG_VIDEO_IPUV3 */
-
-static int ar8035_phy_fixup(struct phy_device *phydev)
-{
- unsigned short val;
-
- /* To enable AR8035 ouput a 125MHz clk from CLK_25M */
- phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
- phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
- phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
-
- val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
- val &= 0xffe3;
- val |= 0x18;
- phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
-
- /* introduce tx clock delay */
- phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
- val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
- val |= 0x0100;
- phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
-
- return 0;
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
- ar8035_phy_fixup(phydev);
-
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
- setup_iomux_enet();
- setup_pcie();
- return cpu_eth_init(bis);
-}
-
-int board_early_init_f(void)
-{
- setup_iomux_uart();
- return 0;
-}
-
-#ifdef CONFIG_CMD_BMODE
-static const struct boot_mode board_boot_modes[] = {
- /* 4 bit bus width */
- {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
- {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
- /* 8 bit bus width */
- {"emmc", MAKE_CFGVAL(0x60, 0x58, 0x00, 0x00)},
- {NULL, 0},
-};
-#endif
-
-#ifdef CONFIG_USB_EHCI_MX6
-static iomux_v3_cfg_t const usb_otg_pads[] = {
- MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-#endif
-
-int board_init(void)
-{
- /* address of boot parameters */
- gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-
-#ifdef CONFIG_VIDEO_IPUV3
- setup_display();
-#endif
-#ifdef CONFIG_SYS_I2C
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
-#endif
-#ifdef CONFIG_DWC_AHSATA
- setup_sata();
-#endif
-#ifdef CONFIG_CMD_BMODE
- add_board_boot_modes(board_boot_modes);
-#endif
-#ifdef CONFIG_USB_EHCI_MX6
- imx_iomux_v3_setup_multiple_pads(
- usb_otg_pads, ARRAY_SIZE(usb_otg_pads));
-#endif
- return 0;
-}
-
-int checkboard(void)
-{
- puts("Board: TBS2910 Matrix ARM mini PC\n");
- return 0;
-}
diff --git a/board/tbs/tbs2910/tbs2910.cfg b/board/tbs/tbs2910/tbs2910.cfg
deleted file mode 100644
index 3ca807b3157..00000000000
--- a/board/tbs/tbs2910/tbs2910.cfg
+++ /dev/null
@@ -1,114 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2017 Soeren Moch <smoch at web.de>
- */
-
-#define __ASSEMBLY__
-#include "asm/arch/crm_regs.h"
-#include "asm/arch/iomux.h"
-#include "asm/arch/mx6-ddr.h"
-
-/* image version 2 for imx6 */
-IMAGE_VERSION 2
-BOOT_FROM sd
-
-/* set the default clock gates to save power */
-DATA 4, CCM_CCGR0, 0x00C03F3F
-DATA 4, CCM_CCGR1, 0x0030FC03
-DATA 4, CCM_CCGR2, 0x0FFFC000
-DATA 4, CCM_CCGR3, 0x3FF00000
-DATA 4, CCM_CCGR4, 0x00FFF300
-DATA 4, CCM_CCGR5, 0x0F0000C3
-DATA 4, CCM_CCGR6, 0x000003FF
-/* set CKO1 (used as AUDIO_MCLK) to ahb_clk_root/8 = 16.5 MHz */
-DATA 4, CCM_CCOSR, 0x000000fb
-
-/* enable AXI cache for VDOA/VPU/IPU */
-DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF
-/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */
-DATA 4, MX6_IOMUXC_GPR6, 0x77177717
-DATA 4, MX6_IOMUXC_GPR7, 0x77177717
-
-
-/*
- * DDR3/DDR3L settings
- * use default 40 Ohm pad drive strength, no odt
- * 4x256Mx16 DDR3L-1066 7-7-7
- */
-
-/* disable dq pullup */
-DATA 4, MX6_IOM_GRP_DDRPKE, 0x00000000
-/* disable dqs pullup */
-DATA 4, MX6_IOM_DRAM_SDQS0, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS1, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS2, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS3, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS4, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS5, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS6, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS7, 0x00000030
-/* set ddr input mode for dq signals */
-DATA 4, MX6_IOM_GRP_DDRMODE, 0x00020000
-/* set ddr input mode for dqs signals */
-DATA 4, MX6_IOM_DDRMODE_CTL, 0x00020000
-/* set pad calibration type to DDR3 */
-DATA 4, MX6_IOM_GRP_DDR_TYPE, 0x000C0000
-/* ZQ calibration */
-DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xA1390003
-/* dqs write delay */
-DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x001f001f
-DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x001f001f
-DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x001f001f
-DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x001f001f
-/* dqs read delay */
-DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333
-/* dqs read gating control */
-DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x43000300
-DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x03000300
-DATA 4, MX6_MMDC_P1_MPDGCTRL0, 0x43000300
-DATA 4, MX6_MMDC_P1_MPDGCTRL1, 0x03000300
-/* start delay line calibration */
-DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800
-/* tRFC=0x89+1,tXS=0x8e+1,tXP=3+1,tXPDLL=0xc+1,tFAW=0x17+1,tCL=0x4+3 */
-DATA 4, MX6_MMDC_P0_MDCFG0, 0x898E7974
-/* tRCD=6+1,tRP=6+1,tRC=0x1a+1,tRAS=0x13+1,tRPA=tRP+1,tWR=7+1,tMRD=0xb+1,tCWL=4+2 */
-DATA 4, MX6_MMDC_P0_MDCFG1, 0xDB538F64
-/* tDLLK=0x1ff+1,tRTP=3+1,tWTR=3+1,tRRD=3+1 */
-DATA 4, MX6_MMDC_P0_MDCFG2, 0x01FF00DB
-/* RTW_SAME=2,WTR_DIFF=3,WTW_DIFF=3,RTW_DIFF=2,RTR_DIFF=2 */
-DATA 4, MX6_MMDC_P0_MDRWD, 0x000026D2
-/* tXPR=0x8e+1,SDE2RST=0x10-2,RST2CKE=0x23-2 */
-DATA 4, MX6_MMDC_P0_MDOR, 0x008E1023
-/* ODT timing */
-DATA 4, MX6_MMDC_P0_MDOTC, 0x09444040
-/* read odt settings, 120 Ohm */
-DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00011117
-DATA 4, MX6_MMDC_P1_MPODTCTRL, 0x00011117
-/* cs0, 15-bit row, 10-bit column, BL 8, 64-bit bus */
-DATA 4, MX6_MMDC_P0_MDCTL, 0x841A0000
-/* interleaved bank access (row/bank/col), 5 cycles additional read delay */
-DATA 4, MX6_MMDC_P0_MDMISC, 0x00001740
-/* 2GiByte RAM at cs0 */
-DATA 4, MX6_MMDC_P0_MDASP, 0x00000047
-/* load mode registers of external ddr chips */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x19308030
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00428031
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04088032
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033
-/* externel chip ZQ calibration */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040
-/* configure and start refreshes, 8 refresh commands at 32 kHz */
-DATA 4, MX6_MMDC_P0_MDREF, 0x00007800
-/* tCKE=2+1,tCKSRX=6,tCKSE=6, active power down after 256 cycles (setting 5) */
-DATA 4, MX6_MMDC_P0_MDPDC, 0x00025576
-/* set automatic self refresh */
-DATA 4, MX6_MMDC_P0_MAPSR, 0x00011006
-/* controller configuration finished */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000
diff --git a/configs/tbs2910_defconfig b/configs/tbs2910_defconfig
deleted file mode 100644
index 55cd9bd998f..00000000000
--- a/configs/tbs2910_defconfig
+++ /dev/null
@@ -1,58 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SYS_THUMB_BUILD=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_TARGET_TBS2910=y
-CONFIG_CMD_HDMIDETECT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_FIT=y
-CONFIG_BOOTDELAY=3
-CONFIG_PRE_CONSOLE_BUFFER=y
-CONFIG_PRE_CON_BUF_ADDR=0x7c000000
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="Matrix U-Boot> "
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_MEMTEST=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PART=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_SATA=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_USB_MASS_STORAGE=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_EFI_PARTITION=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_DM=y
-CONFIG_DWC_AHSATA=y
-CONFIG_FSL_ESDHC=y
-CONFIG_PHYLIB=y
-CONFIG_MII=y
-CONFIG_PCI=y
-CONFIG_DM_THERMAL=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_KEYBOARD=y
-CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="TBS"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0525
-CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
-CONFIG_CI_UDC=y
-CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_VIDEO=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/tbs2910.h b/include/configs/tbs2910.h
deleted file mode 100644
index a60223c6235..00000000000
--- a/include/configs/tbs2910.h
+++ /dev/null
@@ -1,158 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2014 Soeren Moch <smoch at web.de>
- *
- * Configuration settings for the TBS2910 MatrixARM board.
- */
-
-#ifndef __TBS2910_CONFIG_H
-#define __TBS2910_CONFIG_H
-
-#include "mx6_common.h"
-
-/* General configuration */
-
-#define CONFIG_MACH_TYPE 3980
-
-#define CONFIG_SYS_HZ 1000
-
-#define CONFIG_IMX_THERMAL
-
-/* Physical Memory Map */
-#define CONFIG_SYS_SDRAM_BASE MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024 * 1024)
-
-#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END \
- (CONFIG_SYS_MEMTEST_START + 500 * 1024 * 1024)
-
-#define CONFIG_SYS_BOOTMAPSZ 0x10000000
-
-/* Serial console */
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART1_BASE /* select UART1/UART2 */
-
-/* Filesystems / image support */
-
-/* MMC */
-#define CONFIG_SYS_FSL_USDHC_NUM 3
-#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC4_BASE_ADDR
-#define CONFIG_SUPPORT_EMMC_BOOT
-
-/* Ethernet */
-#define CONFIG_FEC_MXC
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 4
-#define CONFIG_PHY_ATHEROS
-
-/* Framebuffer */
-#ifdef CONFIG_VIDEO
-#define CONFIG_VIDEO_IPUV3
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_IMX_HDMI
-#define CONFIG_IMX_VIDEO_SKIP
-#endif
-
-/* PCI */
-#ifdef CONFIG_CMD_PCI
-#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_PCIE_IMX
-#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12)
-#endif
-
-/* SATA */
-#ifdef CONFIG_CMD_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
-#define CONFIG_DWC_AHSATA_PORT_ID 0
-#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
-#define CONFIG_LBA48
-#endif
-
-/* USB */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
-#ifdef CONFIG_CMD_USB_MASS_STORAGE
-#define CONFIG_USBD_HS
-#endif /* CONFIG_CMD_USB_MASS_STORAGE */
-#ifdef CONFIG_USB_KEYBOARD
-#define CONFIG_PREBOOT \
- "usb start; " \
- "if hdmidet; then " \
- "run set_con_hdmi; " \
- "else " \
- "run set_con_serial; " \
- "fi;"
-#endif /* CONFIG_USB_KEYBOARD */
-#endif /* CONFIG_CMD_USB */
-
-/* RTC */
-#ifdef CONFIG_CMD_DATE
-#define CONFIG_RTC_DS1307
-#define CONFIG_SYS_RTC_BUS_NUM 2
-#endif
-
-/* I2C */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_I2C_EDID
-#endif
-
-/* Environment organization */
-#define CONFIG_SYS_MMC_ENV_DEV 2 /* overwritten on SD boot */
-#define CONFIG_SYS_MMC_ENV_PART 1 /* overwritten on SD boot */
-#define CONFIG_ENV_SIZE (8 * 1024)
-#define CONFIG_ENV_OFFSET (384 * 1024)
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "bootargs_mmc1=console=ttymxc0,115200 di0_primary console=tty1\0" \
- "bootargs_mmc2=video=mxcfb0:dev=hdmi,1920x1080M at 60 " \
- "video=mxcfb1:off video=mxcfb2:off fbmem=28M\0" \
- "bootargs_mmc3=root=/dev/mmcblk0p1 rootwait consoleblank=0 quiet\0" \
- "bootargs_mmc=setenv bootargs ${bootargs_mmc1} ${bootargs_mmc2} " \
- "${bootargs_mmc3}\0" \
- "bootargs_upd=setenv bootargs console=ttymxc0,115200 " \
- "rdinit=/sbin/init enable_wait_mode=off\0" \
- "bootcmd_mmc=run bootargs_mmc; mmc dev 2; " \
- "mmc read 0x10800000 0x800 0x4000; bootm 0x10800000\0" \
- "bootcmd_up1=load mmc 1 0x10800000 uImage\0" \
- "bootcmd_up2=load mmc 1 0x10d00000 uramdisk.img; " \
- "run bootargs_upd; " \
- "bootm 0x10800000 0x10d00000\0" \
- "console=ttymxc0\0" \
- "fan=gpio set 92\0" \
- "set_con_serial=setenv stdout serial; " \
- "setenv stderr serial;\0" \
- "set_con_hdmi=setenv stdout serial,vga; " \
- "setenv stderr serial,vga;\0" \
- "stderr=serial,vga;\0" \
- "stdin=serial,usbkbd;\0" \
- "stdout=serial,vga;\0"
-
-#define CONFIG_BOOTCOMMAND \
- "mmc rescan; " \
- "if run bootcmd_up1; then " \
- "run bootcmd_up2; " \
- "else " \
- "run bootcmd_mmc; " \
- "fi"
-
-#endif /* __TBS2910_CONFIG_H * */
--
2.19.1.1215.g8438c0b245-goog
More information about the U-Boot
mailing list