[U-Boot] [PATCH 56/93] arm: Remove am335x_baltos board
Simon Glass
sjg at chromium.org
Mon Nov 19 15:53:36 UTC 2018
This board has not been converted to CONFIG_DM_BLK by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg at chromium.org>
---
arch/arm/Kconfig | 1 -
board/vscom/baltos/Kconfig | 15 -
board/vscom/baltos/MAINTAINERS | 6 -
board/vscom/baltos/Makefile | 11 -
board/vscom/baltos/README | 1 -
board/vscom/baltos/board.c | 493 --------------------------------
board/vscom/baltos/board.h | 34 ---
board/vscom/baltos/mux.c | 125 --------
board/vscom/baltos/u-boot.lds | 128 ---------
configs/am335x_baltos_defconfig | 65 -----
include/configs/baltos.h | 276 ------------------
11 files changed, 1155 deletions(-)
delete mode 100644 board/vscom/baltos/Kconfig
delete mode 100644 board/vscom/baltos/MAINTAINERS
delete mode 100644 board/vscom/baltos/Makefile
delete mode 100644 board/vscom/baltos/README
delete mode 100644 board/vscom/baltos/board.c
delete mode 100644 board/vscom/baltos/board.h
delete mode 100644 board/vscom/baltos/mux.c
delete mode 100644 board/vscom/baltos/u-boot.lds
delete mode 100644 configs/am335x_baltos_defconfig
delete mode 100644 include/configs/baltos.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index b1eeb39d919..6cadd96378b 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1528,7 +1528,6 @@ source "board/spear/x600/Kconfig"
source "board/st/stv0991/Kconfig"
source "board/tcl/sl50/Kconfig"
source "board/ucRobotics/bubblegum_96/Kconfig"
-source "board/vscom/baltos/Kconfig"
source "board/woodburn/Kconfig"
source "board/xilinx/Kconfig"
source "board/xilinx/zynq/Kconfig"
diff --git a/board/vscom/baltos/Kconfig b/board/vscom/baltos/Kconfig
deleted file mode 100644
index b721ed19d80..00000000000
--- a/board/vscom/baltos/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_AM335X_BALTOS
-
-config SYS_BOARD
- default "baltos"
-
-config SYS_VENDOR
- default "vscom"
-
-config SYS_SOC
- default "am33xx"
-
-config SYS_CONFIG_NAME
- default "baltos"
-
-endif
diff --git a/board/vscom/baltos/MAINTAINERS b/board/vscom/baltos/MAINTAINERS
deleted file mode 100644
index e82acfed161..00000000000
--- a/board/vscom/baltos/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-BALTOS BOARD
-M: Yegor Yefremov <yegorslists at googlemail.com>
-S: Maintained
-F: board/vscom/baltos/
-F: include/configs/baltos.h
-F: configs/am335x_baltos_defconfig
diff --git a/board/vscom/baltos/Makefile b/board/vscom/baltos/Makefile
deleted file mode 100644
index c34b9b1dd8a..00000000000
--- a/board/vscom/baltos/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Makefile
-#
-# Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
-
-ifeq ($(CONFIG_SKIP_LOWLEVEL_INIT),)
-obj-y := mux.o
-endif
-
-obj-y += board.o
diff --git a/board/vscom/baltos/README b/board/vscom/baltos/README
deleted file mode 100644
index f744ace9972..00000000000
--- a/board/vscom/baltos/README
+++ /dev/null
@@ -1 +0,0 @@
-BSP for VScom OnRISC Balios family devices, like Balios iR 5221.
diff --git a/board/vscom/baltos/board.c b/board/vscom/baltos/board.c
deleted file mode 100644
index df0a2d2b7a6..00000000000
--- a/board/vscom/baltos/board.c
+++ /dev/null
@@ -1,493 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * board.c
- *
- * Board functions for TI AM335X based boards
- *
- * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
- */
-
-#include <common.h>
-#include <errno.h>
-#include <linux/libfdt.h>
-#include <spl.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/omap.h>
-#include <asm/arch/ddr_defs.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mmc_host_def.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/mem.h>
-#include <asm/arch/mux.h>
-#include <asm/io.h>
-#include <asm/emif.h>
-#include <asm/gpio.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <cpsw.h>
-#include <power/tps65217.h>
-#include <power/tps65910.h>
-#include <environment.h>
-#include <watchdog.h>
-#include "board.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* GPIO that controls power to DDR on EVM-SK */
-#define GPIO_DDR_VTT_EN 7
-#define DIP_S1 44
-#define MPCIE_SW 100
-
-static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
-
-static int baltos_set_console(void)
-{
- int val, i, dips = 0;
- char buf[7];
-
- for (i = 0; i < 4; i++) {
- sprintf(buf, "dip_s%d", i + 1);
-
- if (gpio_request(DIP_S1 + i, buf)) {
- printf("failed to export GPIO %d\n", DIP_S1 + i);
- return 0;
- }
-
- if (gpio_direction_input(DIP_S1 + i)) {
- printf("failed to set GPIO %d direction\n", DIP_S1 + i);
- return 0;
- }
-
- val = gpio_get_value(DIP_S1 + i);
- dips |= val << i;
- }
-
- printf("DIPs: 0x%1x\n", (~dips) & 0xf);
-
- if ((dips & 0xf) == 0xe)
- env_set("console", "ttyUSB0,115200n8");
-
- return 0;
-}
-
-static int read_eeprom(BSP_VS_HWPARAM *header)
-{
- i2c_set_bus_num(1);
-
- /* Check if baseboard eeprom is available */
- if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) {
- puts("Could not probe the EEPROM; something fundamentally "
- "wrong on the I2C bus.\n");
- return -ENODEV;
- }
-
- /* read the eeprom using i2c */
- if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,
- sizeof(BSP_VS_HWPARAM))) {
- puts("Could not read the EEPROM; something fundamentally"
- " wrong on the I2C bus.\n");
- return -EIO;
- }
-
- if (header->Magic != 0xDEADBEEF) {
-
- printf("Incorrect magic number (0x%x) in EEPROM\n",
- header->Magic);
-
- /* fill default values */
- header->SystemId = 211;
- header->MAC1[0] = 0x00;
- header->MAC1[1] = 0x00;
- header->MAC1[2] = 0x00;
- header->MAC1[3] = 0x00;
- header->MAC1[4] = 0x00;
- header->MAC1[5] = 0x01;
-
- header->MAC2[0] = 0x00;
- header->MAC2[1] = 0x00;
- header->MAC2[2] = 0x00;
- header->MAC2[3] = 0x00;
- header->MAC2[4] = 0x00;
- header->MAC2[5] = 0x02;
-
- header->MAC3[0] = 0x00;
- header->MAC3[1] = 0x00;
- header->MAC3[2] = 0x00;
- header->MAC3[3] = 0x00;
- header->MAC3[4] = 0x00;
- header->MAC3[5] = 0x03;
- }
-
- return 0;
-}
-
-#if defined(CONFIG_SPL_BUILD) || defined(CONFIG_NOR_BOOT)
-
-static const struct ddr_data ddr3_baltos_data = {
- .datardsratio0 = MT41K256M16HA125E_RD_DQS,
- .datawdsratio0 = MT41K256M16HA125E_WR_DQS,
- .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
- .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
-};
-
-static const struct cmd_control ddr3_baltos_cmd_ctrl_data = {
- .cmd0csratio = MT41K256M16HA125E_RATIO,
- .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
-
- .cmd1csratio = MT41K256M16HA125E_RATIO,
- .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
-
- .cmd2csratio = MT41K256M16HA125E_RATIO,
- .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
-};
-
-static struct emif_regs ddr3_baltos_emif_reg_data = {
- .sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
- .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
- .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
- .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
- .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
- .zq_config = MT41K256M16HA125E_ZQ_CFG,
- .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
-};
-
-#ifdef CONFIG_SPL_OS_BOOT
-int spl_start_uboot(void)
-{
- /* break into full u-boot on 'c' */
- return (serial_tstc() && serial_getc() == 'c');
-}
-#endif
-
-#define OSC (V_OSCK/1000000)
-const struct dpll_params dpll_ddr = {
- 266, OSC-1, 1, -1, -1, -1, -1};
-const struct dpll_params dpll_ddr_evm_sk = {
- 303, OSC-1, 1, -1, -1, -1, -1};
-const struct dpll_params dpll_ddr_baltos = {
- 400, OSC-1, 1, -1, -1, -1, -1};
-
-void am33xx_spl_board_init(void)
-{
- int mpu_vdd;
- int sil_rev;
-
- /* Get the frequency */
- dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
-
- /*
- * The GP EVM, IDK and EVM SK use a TPS65910 PMIC. For all
- * MPU frequencies we support we use a CORE voltage of
- * 1.1375V. For MPU voltage we need to switch based on
- * the frequency we are running at.
- */
- i2c_set_bus_num(1);
-
- printf("I2C speed: %d Hz\n", CONFIG_SYS_OMAP24_I2C_SPEED);
-
- if (i2c_probe(TPS65910_CTRL_I2C_ADDR)) {
- puts("i2c: cannot access TPS65910\n");
- return;
- }
-
- /*
- * Depending on MPU clock and PG we will need a different
- * VDD to drive at that speed.
- */
- sil_rev = readl(&cdev->deviceid) >> 28;
- mpu_vdd = am335x_get_tps65910_mpu_vdd(sil_rev,
- dpll_mpu_opp100.m);
-
- /* Tell the TPS65910 to use i2c */
- tps65910_set_i2c_control();
-
- /* First update MPU voltage. */
- if (tps65910_voltage_update(MPU, mpu_vdd))
- return;
-
- /* Second, update the CORE voltage. */
- if (tps65910_voltage_update(CORE, TPS65910_OP_REG_SEL_1_1_3))
- return;
-
- /* Set CORE Frequencies to OPP100 */
- do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
-
- /* Set MPU Frequency to what we detected now that voltages are set */
- do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
-
- writel(0x000010ff, PRM_DEVICE_INST + 4);
-}
-
-const struct dpll_params *get_dpll_ddr_params(void)
-{
- enable_i2c1_pin_mux();
- i2c_set_bus_num(1);
-
- return &dpll_ddr_baltos;
-}
-
-void set_uart_mux_conf(void)
-{
- enable_uart0_pin_mux();
-}
-
-void set_mux_conf_regs(void)
-{
- enable_board_pin_mux();
-}
-
-const struct ctrl_ioregs ioregs_baltos = {
- .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
-};
-
-void sdram_init(void)
-{
- gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");
- gpio_direction_output(GPIO_DDR_VTT_EN, 1);
-
- config_ddr(400, &ioregs_baltos,
- &ddr3_baltos_data,
- &ddr3_baltos_cmd_ctrl_data,
- &ddr3_baltos_emif_reg_data, 0);
-}
-#endif
-
-/*
- * Basic board specific setup. Pinmux has been handled already.
- */
-int board_init(void)
-{
-#if defined(CONFIG_HW_WATCHDOG)
- hw_watchdog_init();
-#endif
-
- gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-#if defined(CONFIG_NOR) || defined(CONFIG_NAND)
- gpmc_init();
-#endif
- return 0;
-}
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
- int node, ret;
- unsigned char mac_addr[6];
- BSP_VS_HWPARAM header;
-
- /* get production data */
- if (read_eeprom(&header))
- return 0;
-
- /* setup MAC1 */
- mac_addr[0] = header.MAC1[0];
- mac_addr[1] = header.MAC1[1];
- mac_addr[2] = header.MAC1[2];
- mac_addr[3] = header.MAC1[3];
- mac_addr[4] = header.MAC1[4];
- mac_addr[5] = header.MAC1[5];
-
-
- node = fdt_path_offset(blob, "/ocp/ethernet/slave at 4a100200");
- if (node < 0) {
- printf("no /soc/fman/ethernet path offset\n");
- return -ENODEV;
- }
-
- ret = fdt_setprop(blob, node, "mac-address", &mac_addr, 6);
- if (ret) {
- printf("error setting local-mac-address property\n");
- return -ENODEV;
- }
-
- /* setup MAC2 */
- mac_addr[0] = header.MAC2[0];
- mac_addr[1] = header.MAC2[1];
- mac_addr[2] = header.MAC2[2];
- mac_addr[3] = header.MAC2[3];
- mac_addr[4] = header.MAC2[4];
- mac_addr[5] = header.MAC2[5];
-
- node = fdt_path_offset(blob, "/ocp/ethernet/slave at 4a100300");
- if (node < 0) {
- printf("no /soc/fman/ethernet path offset\n");
- return -ENODEV;
- }
-
- ret = fdt_setprop(blob, node, "mac-address", &mac_addr, 6);
- if (ret) {
- printf("error setting local-mac-address property\n");
- return -ENODEV;
- }
-
- printf("\nFDT was successfully setup\n");
-
- return 0;
-}
-
-static struct module_pin_mux pcie_sw_pin_mux[] = {
- {OFFSET(mii1_rxdv), (MODE(7) | PULLUDEN )}, /* GPIO3_4 */
- {-1},
-};
-
-static struct module_pin_mux dip_pin_mux[] = {
- {OFFSET(gpmc_ad12), (MODE(7) | RXACTIVE )}, /* GPIO1_12 */
- {OFFSET(gpmc_ad13), (MODE(7) | RXACTIVE )}, /* GPIO1_13 */
- {OFFSET(gpmc_ad14), (MODE(7) | RXACTIVE )}, /* GPIO1_14 */
- {OFFSET(gpmc_ad15), (MODE(7) | RXACTIVE )}, /* GPIO1_15 */
- {-1},
-};
-
-#ifdef CONFIG_BOARD_LATE_INIT
-int board_late_init(void)
-{
-#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- BSP_VS_HWPARAM header;
- char model[4];
-
- /* get production data */
- if (read_eeprom(&header)) {
- strcpy(model, "211");
- } else {
- sprintf(model, "%d", header.SystemId);
- if (header.SystemId == 215) {
- configure_module_pin_mux(dip_pin_mux);
- baltos_set_console();
- }
- }
-
- /* turn power for the mPCIe slot */
- configure_module_pin_mux(pcie_sw_pin_mux);
- if (gpio_request(MPCIE_SW, "mpcie_sw")) {
- printf("failed to export GPIO %d\n", MPCIE_SW);
- return -ENODEV;
- }
- if (gpio_direction_output(MPCIE_SW, 1)) {
- printf("failed to set GPIO %d direction\n", MPCIE_SW);
- return -ENODEV;
- }
-
- env_set("board_name", model);
-#endif
-
- return 0;
-}
-#endif
-
-#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
- (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
-static void cpsw_control(int enabled)
-{
- /* VTP can be added here */
-
- return;
-}
-
-static struct cpsw_slave_data cpsw_slaves[] = {
- {
- .slave_reg_ofs = 0x208,
- .sliver_reg_ofs = 0xd80,
- .phy_addr = 0,
- },
- {
- .slave_reg_ofs = 0x308,
- .sliver_reg_ofs = 0xdc0,
- .phy_addr = 7,
- },
-};
-
-static struct cpsw_platform_data cpsw_data = {
- .mdio_base = CPSW_MDIO_BASE,
- .cpsw_base = CPSW_BASE,
- .mdio_div = 0xff,
- .channels = 8,
- .cpdma_reg_ofs = 0x800,
- .slaves = 2,
- .slave_data = cpsw_slaves,
- .active_slave = 1,
- .ale_reg_ofs = 0xd00,
- .ale_entries = 1024,
- .host_port_reg_ofs = 0x108,
- .hw_stats_reg_ofs = 0x900,
- .bd_ram_ofs = 0x2000,
- .mac_control = (1 << 5),
- .control = cpsw_control,
- .host_port_num = 0,
- .version = CPSW_CTRL_VERSION_2,
-};
-#endif
-
-#if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USB_ETHER)) \
- && defined(CONFIG_SPL_BUILD)) || \
- ((defined(CONFIG_DRIVER_TI_CPSW) || \
- defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) && \
- !defined(CONFIG_SPL_BUILD))
-int board_eth_init(bd_t *bis)
-{
- int rv, n = 0;
- uint8_t mac_addr[6];
- uint32_t mac_hi, mac_lo;
-
- /*
- * Note here that we're using CPSW1 since that has a 1Gbit PHY while
- * CSPW0 has a 100Mbit PHY.
- *
- * On product, CPSW1 maps to port labeled WAN.
- */
-
- /* try reading mac address from efuse */
- mac_lo = readl(&cdev->macid1l);
- mac_hi = readl(&cdev->macid1h);
- mac_addr[0] = mac_hi & 0xFF;
- mac_addr[1] = (mac_hi & 0xFF00) >> 8;
- mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
- mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
- mac_addr[4] = mac_lo & 0xFF;
- mac_addr[5] = (mac_lo & 0xFF00) >> 8;
-
-#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
- (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
- if (!env_get("ethaddr")) {
- printf("<ethaddr> not set. Validating first E-fuse MAC\n");
-
- if (is_valid_ethaddr(mac_addr))
- eth_env_set_enetaddr("ethaddr", mac_addr);
- }
-
-#ifdef CONFIG_DRIVER_TI_CPSW
- writel((GMII1_SEL_RMII | GMII2_SEL_RGMII | RGMII2_IDMODE), &cdev->miisel);
- cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_RGMII;
- rv = cpsw_register(&cpsw_data);
- if (rv < 0)
- printf("Error %d registering CPSW switch\n", rv);
- else
- n += rv;
-#endif
-
- /*
- *
- * CPSW RGMII Internal Delay Mode is not supported in all PVT
- * operating points. So we must set the TX clock delay feature
- * in the AR8051 PHY. Since we only support a single ethernet
- * device in U-Boot, we only do this for the first instance.
- */
-#define AR8051_PHY_DEBUG_ADDR_REG 0x1d
-#define AR8051_PHY_DEBUG_DATA_REG 0x1e
-#define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5
-#define AR8051_RGMII_TX_CLK_DLY 0x100
- const char *devname;
- devname = miiphy_get_current_dev();
-
- miiphy_write(devname, 0x7, AR8051_PHY_DEBUG_ADDR_REG,
- AR8051_DEBUG_RGMII_CLK_DLY_REG);
- miiphy_write(devname, 0x7, AR8051_PHY_DEBUG_DATA_REG,
- AR8051_RGMII_TX_CLK_DLY);
-#endif
- return n;
-}
-#endif
diff --git a/board/vscom/baltos/board.h b/board/vscom/baltos/board.h
deleted file mode 100644
index 630c9bba73b..00000000000
--- a/board/vscom/baltos/board.h
+++ /dev/null
@@ -1,34 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * board.h
- *
- * TI AM335x boards information header
- *
- * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
- */
-
-#ifndef _BOARD_H_
-#define _BOARD_H_
-
-typedef struct _BSP_VS_HWPARAM // v1.0
-{
- uint32_t Magic;
- uint32_t HwRev;
- uint32_t SerialNumber;
- char PrdDate[11]; // as a string ie. "01.01.2006"
- uint16_t SystemId;
- uint8_t MAC1[6]; // internal EMAC
- uint8_t MAC2[6]; // SMSC9514
- uint8_t MAC3[6]; // WL1271 WLAN
-} __attribute__ ((packed)) BSP_VS_HWPARAM;
-
-/*
- * We have three pin mux functions that must exist. We must be able to enable
- * uart0, for initial output and i2c0 to read the main EEPROM. We then have a
- * main pinmux function that can be overridden to enable all other pinmux that
- * is required on the board.
- */
-void enable_uart0_pin_mux(void);
-void enable_i2c1_pin_mux(void);
-void enable_board_pin_mux(void);
-#endif
diff --git a/board/vscom/baltos/mux.c b/board/vscom/baltos/mux.c
deleted file mode 100644
index 94410ae35e6..00000000000
--- a/board/vscom/baltos/mux.c
+++ /dev/null
@@ -1,125 +0,0 @@
-/*
- * mux.c
- *
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <common.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/mux.h>
-#include <asm/io.h>
-#include <i2c.h>
-#include "board.h"
-
-static struct module_pin_mux uart0_pin_mux[] = {
- {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* UART0_RXD */
- {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, /* UART0_TXD */
- {-1},
-};
-
-static struct module_pin_mux mmc0_pin_mux[] = {
- {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT3 */
- {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT2 */
- {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT1 */
- {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT0 */
- {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CLK */
- {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CMD */
- //{OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)}, /* MMC0_CD */
- {-1},
-};
-
-static struct module_pin_mux i2c1_pin_mux[] = {
- {OFFSET(spi0_d1), (MODE(2) | RXACTIVE |
- PULLUDEN | SLEWCTRL)}, /* I2C_DATA */
- {OFFSET(spi0_cs0), (MODE(2) | RXACTIVE |
- PULLUDEN | SLEWCTRL)}, /* I2C_SCLK */
- {-1},
-};
-
-static struct module_pin_mux gpio0_7_pin_mux[] = {
- {OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDEN)}, /* GPIO0_7 */
- {-1},
-};
-
-static struct module_pin_mux rmii1_pin_mux[] = {
- {OFFSET(mii1_crs), MODE(1) | RXACTIVE}, /* RGMII1_TCTL */
- {OFFSET(mii1_txen), MODE(1)}, /* RGMII1_TCTL */
- {OFFSET(mii1_txd1), MODE(1)}, /* RGMII1_TCTL */
- {OFFSET(mii1_txd0), MODE(1)}, /* RGMII1_TCTL */
- {OFFSET(mii1_rxd1), MODE(1) | RXACTIVE}, /* RGMII1_TCTL */
- {OFFSET(mii1_rxd0), MODE(1) | RXACTIVE}, /* RGMII1_TCTL */
- {OFFSET(rmii1_refclk), MODE(0) | RXACTIVE}, /* RGMII1_TCTL */
- {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
- {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
- {-1},
-};
-
-static struct module_pin_mux rgmii2_pin_mux[] = {
- {OFFSET(gpmc_a0), MODE(2)}, /* RGMII1_TCTL */
- {OFFSET(gpmc_a1), MODE(2) | RXACTIVE}, /* RGMII1_RCTL */
- {OFFSET(gpmc_a2), MODE(2)}, /* RGMII1_TD3 */
- {OFFSET(gpmc_a3), MODE(2)}, /* RGMII1_TD2 */
- {OFFSET(gpmc_a4), MODE(2)}, /* RGMII1_TD1 */
- {OFFSET(gpmc_a5), MODE(2)}, /* RGMII1_TD0 */
- {OFFSET(gpmc_a6), MODE(2)}, /* RGMII1_TCLK */
- {OFFSET(gpmc_a7), MODE(2) | RXACTIVE}, /* RGMII1_RCLK */
- {OFFSET(gpmc_a8), MODE(2) | RXACTIVE}, /* RGMII1_RD3 */
- {OFFSET(gpmc_a9), MODE(2) | RXACTIVE}, /* RGMII1_RD2 */
- {OFFSET(gpmc_a10), MODE(2) | RXACTIVE}, /* RGMII1_RD1 */
- {OFFSET(gpmc_a11), MODE(2) | RXACTIVE}, /* RGMII1_RD0 */
- {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
- {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
- {-1},
-};
-
-static struct module_pin_mux nand_pin_mux[] = {
- {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */
- {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */
- {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */
- {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */
- {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */
- {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */
- {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */
- {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */
- {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
- {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */
- {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */
- {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
- {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */
- {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */
- {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */
- {-1},
-};
-
-void enable_uart0_pin_mux(void)
-{
- configure_module_pin_mux(uart0_pin_mux);
-}
-
-void enable_i2c1_pin_mux(void)
-{
- configure_module_pin_mux(i2c1_pin_mux);
-}
-
-void enable_board_pin_mux()
-{
- configure_module_pin_mux(i2c1_pin_mux);
- configure_module_pin_mux(gpio0_7_pin_mux);
- configure_module_pin_mux(rgmii2_pin_mux);
- configure_module_pin_mux(rmii1_pin_mux);
- configure_module_pin_mux(mmc0_pin_mux);
-
-#if defined(CONFIG_NAND)
- configure_module_pin_mux(nand_pin_mux);
-#endif
-}
diff --git a/board/vscom/baltos/u-boot.lds b/board/vscom/baltos/u-boot.lds
deleted file mode 100644
index 315ba5b99a7..00000000000
--- a/board/vscom/baltos/u-boot.lds
+++ /dev/null
@@ -1,128 +0,0 @@
-/*
- * Copyright (c) 2004-2008 Texas Instruments
- *
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj at denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(_start)
-SECTIONS
-{
- . = 0x00000000;
-
- . = ALIGN(4);
- .text :
- {
- *(.__image_copy_start)
- *(.vectors)
- CPUDIR/start.o (.text*)
- board/vscom/baltos/built-in.o (.text*)
- *(.text*)
- }
-
- . = ALIGN(4);
- .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
-
- . = ALIGN(4);
- .data : {
- *(.data*)
- }
-
- . = ALIGN(4);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
- . = ALIGN(4);
-
- .image_copy_end :
- {
- *(.__image_copy_end)
- }
-
- .rel_dyn_start :
- {
- *(.__rel_dyn_start)
- }
-
- .rel.dyn : {
- *(.rel*)
- }
-
- .rel_dyn_end :
- {
- *(.__rel_dyn_end)
- }
-
- .hash : { *(.hash*) }
-
- .end :
- {
- *(.__end)
- }
-
- _image_binary_end = .;
-
- /*
- * Deprecated: this MMU section is used by pxa at present but
- * should not be used by new boards/CPUs.
- */
- . = ALIGN(4096);
- .mmutable : {
- *(.mmutable)
- }
-
-/*
- * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
- * __bss_base and __bss_limit are for linker only (overlay ordering)
- */
-
- .bss_start __rel_dyn_start (OVERLAY) : {
- KEEP(*(.__bss_start));
- __bss_base = .;
- }
-
- .bss __bss_base (OVERLAY) : {
- *(.bss*)
- . = ALIGN(4);
- __bss_limit = .;
- }
-
- .bss_end __bss_limit (OVERLAY) : {
- KEEP(*(.__bss_end));
- }
-
- .dynsym _image_binary_end : { *(.dynsym) }
- .dynbss : { *(.dynbss) }
- .dynstr : { *(.dynstr*) }
- .dynamic : { *(.dynamic*) }
- .gnu.hash : { *(.gnu.hash) }
- .plt : { *(.plt*) }
- .interp : { *(.interp*) }
- .gnu : { *(.gnu*) }
- .ARM.exidx : { *(.ARM.exidx*) }
-}
diff --git a/configs/am335x_baltos_defconfig b/configs/am335x_baltos_defconfig
deleted file mode 100644
index a61b13b6fc9..00000000000
--- a/configs/am335x_baltos_defconfig
+++ /dev/null
@@ -1,65 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_OMAP2PLUS=y
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_AM33XX=y
-CONFIG_TARGET_AM335X_BALTOS=y
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_FAT_SUPPORT=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-CONFIG_VERSION_VARIABLE=y
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_SPL_EXT_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MTD_SUPPORT=y
-CONFIG_SPL_POWER_SUPPORT=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_SPL_YMODEM_SUPPORT=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_EEPROM=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_SPI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=omap2-nand.0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:128k(SPL),128k(SPL.backup1),128k(SPL.backup2),128k(SPL.backup3),1920k(u-boot),-(UBI)"
-CONFIG_CMD_UBI=y
-CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_BOOTCOUNT_LIMIT=y
-CONFIG_SYS_OMAP24_I2C_SPEED=1000
-CONFIG_MMC_OMAP_HS=y
-CONFIG_NAND=y
-CONFIG_PHY_ADDR_ENABLE=y
-CONFIG_DRIVER_TI_CPSW=y
-CONFIG_MII=y
-CONFIG_SPI=y
-CONFIG_OMAP3_SPI=y
-CONFIG_USB=y
-CONFIG_USB_MUSB_HOST=y
-CONFIG_USB_MUSB_GADGET=y
-CONFIG_USB_MUSB_DSPS=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0403
-CONFIG_USB_GADGET_PRODUCT_NUM=0xbd00
-CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_USB_ETHER=y
-CONFIG_USBNET_HOST_ADDR="de:ad:be:af:00:00"
-CONFIG_FAT_WRITE=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/baltos.h b/include/configs/baltos.h
deleted file mode 100644
index 006b049d09d..00000000000
--- a/include/configs/baltos.h
+++ /dev/null
@@ -1,276 +0,0 @@
-/*
- * am335x_evm.h
- *
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __CONFIG_BALTOS_H
-#define __CONFIG_BALTOS_H
-
-#include <linux/sizes.h>
-#include <configs/ti_am335x_common.h>
-
-#define CONFIG_MACH_TYPE MACH_TYPE_AM335XEVM
-
-/* Clock Defines */
-#define V_OSCK 24000000 /* Clock output from T2 */
-#define V_SCLK (V_OSCK)
-
-/* Custom script for NOR */
-#define CONFIG_SYS_LDSCRIPT "board/vscom/baltos/u-boot.lds"
-
-/* Always 128 KiB env size */
-#define CONFIG_ENV_SIZE (128 << 10)
-
-/* FIT support */
-#define CONFIG_SYS_BOOTM_LEN SZ_64M
-
-/* UBI Support */
-
-/* I2C configuration */
-
-#ifdef CONFIG_NAND
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x00080000
-#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000 /* kernel offset */
-#endif
-#define NANDARGS \
- "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
- "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
- "nandargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "${mtdparts} " \
- "root=${nandroot} " \
- "rootfstype=${nandrootfstype}\0" \
- "nandroot=ubi0:rootfs rw ubi.mtd=5\0" \
- "nandrootfstype=ubifs rootwait=1\0" \
- "nandboot=echo Booting from nand ...; " \
- "run nandargs; " \
- "setenv loadaddr 0x84000000; " \
- "ubi part UBI; " \
- "ubifsmount ubi0:kernel; " \
- "ubifsload $loadaddr kernel-fit.itb;" \
- "ubifsumount; " \
- "bootm ${loadaddr}#conf${board_name}; " \
- "if test $? -ne 0; then echo Using default FIT config; " \
- "bootm ${loadaddr}; fi;\0"
-#else
-#define NANDARGS ""
-#endif
-
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_EXTRA_ENV_SETTINGS \
- DEFAULT_LINUX_BOOT_ENV \
- "boot_fdt=try\0" \
- "bootpart=0:2\0" \
- "bootdir=/boot\0" \
- "bootfile=zImage\0" \
- "fdtfile=undefined\0" \
- "console=ttyO0,115200n8\0" \
- "partitions=" \
- "uuid_disk=${uuid_gpt_disk};" \
- "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \
- "optargs=\0" \
- "mmcdev=0\0" \
- "mmcroot=/dev/mmcblk0p2 ro\0" \
- "usbroot=/dev/sda2 ro\0" \
- "mmcrootfstype=ext4 rootwait\0" \
- "usbrootfstype=ext4 rootwait\0" \
- "rootpath=/export/rootfs\0" \
- "nfsopts=nolock\0" \
- "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
- "::off\0" \
- "ramroot=/dev/ram0 rw\0" \
- "ramrootfstype=ext2\0" \
- "mmcargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "${mtdparts} " \
- "root=${mmcroot} " \
- "rootfstype=${mmcrootfstype}\0" \
- "usbargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "${mtdparts} " \
- "root=${usbroot} " \
- "rootfstype=${usbrootfstype}\0" \
- "spiroot=/dev/mtdblock4 rw\0" \
- "spirootfstype=jffs2\0" \
- "spisrcaddr=0xe0000\0" \
- "spiimgsize=0x362000\0" \
- "spibusno=0\0" \
- "spiargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "root=${spiroot} " \
- "rootfstype=${spirootfstype}\0" \
- "netargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "root=/dev/nfs " \
- "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
- "ip=dhcp\0" \
- "bootenv=uEnv.txt\0" \
- "loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
- "usbloadbootenv=load usb 0:1 ${loadaddr} ${bootenv}\0" \
- "importbootenv=echo Importing environment from mmc ...; " \
- "env import -t $loadaddr $filesize\0" \
- "usbimportbootenv=echo Importing environment from USB ...; " \
- "env import -t $loadaddr $filesize\0" \
- "ramargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "root=${ramroot} " \
- "rootfstype=${ramrootfstype}\0" \
- "loadramdisk=load mmc ${mmcdev} ${rdaddr} ramdisk.gz\0" \
- "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
- "usbloadimage=load usb 0:1 ${loadaddr} kernel-fit.itb\0" \
- "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
- "usbloados=run usbargs; " \
- "bootm ${loadaddr}#conf${board_name}; " \
- "if test $? -ne 0; then " \
- "echo Using default FIT configuration; " \
- "bootm ${loadaddr}; " \
- "fi;\0" \
- "mmcloados=run mmcargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootz ${loadaddr} - ${fdtaddr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0" \
- "usbboot=usb reset; " \
- "if usb storage; then " \
- "echo USB drive found;" \
- "if run usbloadbootenv; then " \
- "echo Loaded environment from ${bootenv};" \
- "run usbimportbootenv;" \
- "fi;" \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...;" \
- "run uenvcmd;" \
- "fi;" \
- "if run usbloadimage; then " \
- "run usbloados;" \
- "fi;" \
- "fi;\0" \
- "mmcboot=mmc dev ${mmcdev}; " \
- "if mmc rescan; then " \
- "echo SD/MMC found on device ${mmcdev};" \
- "if run loadbootenv; then " \
- "echo Loaded environment from ${bootenv};" \
- "run importbootenv;" \
- "fi;" \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...;" \
- "run uenvcmd;" \
- "fi;" \
- "if run loadimage; then " \
- "run mmcloados;" \
- "fi;" \
- "fi;\0" \
- "spiboot=echo Booting from spi ...; " \
- "run spiargs; " \
- "sf probe ${spibusno}:0; " \
- "sf read ${loadaddr} ${spisrcaddr} ${spiimgsize}; " \
- "bootz ${loadaddr}\0" \
- "netboot=echo Booting from network ...; " \
- "setenv autoload no; " \
- "dhcp; " \
- "tftp ${loadaddr} ${bootfile}; " \
- "tftp ${fdtaddr} ${fdtfile}; " \
- "run netargs; " \
- "bootz ${loadaddr} - ${fdtaddr}\0" \
- "ramboot=echo Booting from ramdisk ...; " \
- "run ramargs; " \
- "bootz ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
- "findfdt=setenv fdtfile am335x-baltos.dtb\0" \
- NANDARGS
- /*DFUARGS*/
-#endif
-
-#define CONFIG_BOOTCOMMAND \
- "run findfdt; " \
- "run usbboot;" \
- "run mmcboot;" \
- "setenv mmcdev 1; " \
- "setenv bootpart 1:2; " \
- "run mmcboot;" \
- "run nandboot;"
-
-/* NS16550 Configuration */
-#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* Base EVM has UART0 */
-#define CONFIG_SYS_NS16550_COM2 0x48022000 /* UART1 */
-#define CONFIG_SYS_NS16550_COM3 0x48024000 /* UART2 */
-#define CONFIG_SYS_NS16550_COM4 0x481a6000 /* UART3 */
-#define CONFIG_SYS_NS16550_COM5 0x481a8000 /* UART4 */
-#define CONFIG_SYS_NS16550_COM6 0x481aa000 /* UART5 */
-
-#define CONFIG_ENV_EEPROM_IS_ON_I2C
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
-/* PMIC support */
-#define CONFIG_POWER_TPS65910
-
-/* SPL */
-#ifndef CONFIG_NOR_BOOT
-
-#ifdef CONFIG_NAND
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
- CONFIG_SYS_NAND_PAGE_SIZE)
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
-#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
- 10, 11, 12, 13, 14, 15, 16, 17, \
- 18, 19, 20, 21, 22, 23, 24, 25, \
- 26, 27, 28, 29, 30, 31, 32, 33, \
- 34, 35, 36, 37, 38, 39, 40, 41, \
- 42, 43, 44, 45, 46, 47, 48, 49, \
- 50, 51, 52, 53, 54, 55, 56, 57, }
-
-#define CONFIG_SYS_NAND_ECCSIZE 512
-#define CONFIG_SYS_NAND_ECCBYTES 14
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#endif
-#endif
-
-/*
- * USB configuration. We enable MUSB support, both for host and for
- * gadget. We set USB0 as peripheral and USB1 as host, based on the
- * board schematic and physical port wired to each. Then for host we
- * add mass storage support and for gadget we add both RNDIS ethernet
- * and DFU.
- */
-#define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_HOST
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_OTG
-
-/* Network. */
-#define CONFIG_PHY_SMSC
-#define CONFIG_PHY_ATHEROS
-
-/* NAND support */
-#ifdef CONFIG_NAND
-#define GPMC_NAND_ECC_LP_x8_LAYOUT 1
-#endif
-
-#endif /* ! __CONFIG_BALTOS_H */
--
2.19.1.1215.g8438c0b245-goog
More information about the U-Boot
mailing list