[U-Boot] [PATCH v3 1/5] mmc: sunxi: add support for automatic delay calibration

[Andre Przywara]

On Wed, 17 Oct 2018 22:56:47 -0700
Vasily Khoruzhick <anarsoul at gmail.com> wrote:

> A64 and H6 support automatic delay calibration and Linux driver uses
> it instead of hardcoded delays. Add support for it to u-boot driver.
> 
> Fixes eMMC instability on Pinebook
> 
> Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
> Acked-by: Maxime Ripard <maxime.ripard at bootlin.com>
> Tested-by: Maxime Ripard <maxime.ripard at bootlin.com>
> Cc: Vagrant Cascadian <vagrant at debian.org>

Reviewed-by: Andre Przywara <andre.przywara at arm.com>

Cheers,
Andre

> ---
>  arch/arm/include/asm/arch-sunxi/mmc.h |  6 +++++-
>  drivers/mmc/sunxi_mmc.c               | 21 ++++++++++++++++++++-
>  2 files changed, 25 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/include/asm/arch-sunxi/mmc.h
> b/arch/arm/include/asm/arch-sunxi/mmc.h index d98c53faaa..f2deafddd2
> 100644 --- a/arch/arm/include/asm/arch-sunxi/mmc.h
> +++ b/arch/arm/include/asm/arch-sunxi/mmc.h
> @@ -46,7 +46,9 @@ struct sunxi_mmc {
>  	u32 cbda;		/* 0x94 */
>  	u32 res2[26];
>  #if defined(CONFIG_SUNXI_GEN_SUN6I) || defined(CONFIG_MACH_SUN50I_H6)
> -	u32 res3[64];
> +	u32 res3[17];
> +	u32 samp_dl;
> +	u32 res4[46];
>  #endif
>  	u32 fifo;		/* 0x100 / 0x200 FIFO access
> address */ };
> @@ -130,5 +132,7 @@ struct sunxi_mmc {
>  #define SUNXI_MMC_COMMON_CLK_GATE		(1 << 16)
>  #define SUNXI_MMC_COMMON_RESET			(1 << 18)
>  
> +#define SUNXI_MMC_CAL_DL_SW_EN		(0x1 << 7)
> +
>  struct mmc *sunxi_mmc_init(int sdc_no);
>  #endif /* _SUNXI_MMC_H */
> diff --git a/drivers/mmc/sunxi_mmc.c b/drivers/mmc/sunxi_mmc.c
> index 39f15eb423..147eb9b4d5 100644
> --- a/drivers/mmc/sunxi_mmc.c
> +++ b/drivers/mmc/sunxi_mmc.c
> @@ -99,11 +99,16 @@ static int mmc_set_mod_clk(struct sunxi_mmc_priv
> *priv, unsigned int hz) {
>  	unsigned int pll, pll_hz, div, n, oclk_dly, sclk_dly;
>  	bool new_mode = false;
> +	bool calibrate = false;
>  	u32 val = 0;
>  
>  	if (IS_ENABLED(CONFIG_MMC_SUNXI_HAS_NEW_MODE) &&
> (priv->mmc_no == 2)) new_mode = true;
>  
> +#if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN50I_H6)
> +	calibrate = true;
> +#endif
> +
>  	/*
>  	 * The MMC clock has an extra /2 post-divider when operating
> in the new
>  	 * mode.
> @@ -174,7 +179,11 @@ static int mmc_set_mod_clk(struct sunxi_mmc_priv
> *priv, unsigned int hz) val = CCM_MMC_CTRL_MODE_SEL_NEW;
>  		setbits_le32(&priv->reg->ntsr,
> SUNXI_MMC_NTSR_MODE_SEL_NEW); #endif
> -	} else {
> +	} else if (!calibrate) {
> +		/*
> +		 * Use hardcoded delay values if controller doesn't
> support
> +		 * calibration
> +		 */
>  		val = CCM_MMC_CTRL_OCLK_DLY(oclk_dly) |
>  			CCM_MMC_CTRL_SCLK_DLY(sclk_dly);
>  	}
> @@ -228,6 +237,16 @@ static int mmc_config_clock(struct
> sunxi_mmc_priv *priv, struct mmc *mmc) rval &=
> ~SUNXI_MMC_CLK_DIVIDER_MASK; writel(rval, &priv->reg->clkcr);
>  
> +#if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN50I_H6)
> +	/* A64 supports calibration of delays on MMC controller and
> we
> +	 * have to set delay of zero before starting calibration.
> +	 * Allwinner BSP driver sets a delay only in the case of
> +	 * using HS400 which is not supported by mainline U-Boot or
> +	 * Linux at the moment
> +	 */
> +	writel(SUNXI_MMC_CAL_DL_SW_EN, &priv->reg->samp_dl);
> +#endif
> +
>  	/* Re-enable Clock */
>  	rval |= SUNXI_MMC_CLK_ENABLE;
>  	writel(rval, &priv->reg->clkcr);