[U-Boot] [PULL] Please pull u-boot-imx

[Peter Robinson]

Hi Stefano,

> a new PR. I dropped the patches causing breakages on PowerPC boards, as
> well as the issue on GE boards. It ran on travis successfully.
>
>
> The following changes since commit 11ed312896c5f5814064c5d45dcb2f53dc121437:
>
>   configs: am57xx: change default board name to beagle_x15 (2018-08-26
> 12:26:16 -0400)
>
> are available in the Git repository at:
>
>   git://www.denx.de/git/u-boot-imx.git master
>
> for you to fetch changes up to c1d1543ebc6e1fb026d0d7ac96d865faa7567555:
>
>   mx7dsabresd: Add the qspi target to the list of supported defconfigs
> (2018-09-04 08:47:23 +0200)
>
> ----------------------------------------------------------------
> Alex Kiernan (1):
>       Cleanup CONFIG_BOOTDELAY on cl-som-imx7
>
> Anson Huang (3):
>       imx: mx7: psci: improve cpu hotplug flow
>       imx: mx7: add gpc initialization for low power mode
>       imx: mx7: add system suspend/resume support
>
> Fabio Estevam (1):
>       mx7dsabresd: Add the qspi target to the list of supported defconfigs
>
> Martin Kaiser (1):
>       watchdog: mx25: use the imx_watchdog driver for mx25
>
> Stefan Agner (2):
>       board: toradex: common: fail gracefully on missing NAND chip
>       colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support
>
> Stefano Babic (1):
>       imx: missing CONFIG_MII in mx7dsabresd_qspi_defconfig
>
> Ye Li (6):
>       imx: imx6sx-sdb: Enable DM QSPI driver
>       imx: imx6sx-sabreauto: convert to use DM QSPI driver
>       imx: imx7d-sdb: Add DM QSPI support
>       dts: imx6ul: Update alias to support DM
>       dts: imx6ul_evk: Add DTS files for 14x14 EVK and 9x9 EVK boards
>       imx: imx6ul_evk: Enable DM driver for iMX6UL EVK u-boot

Are you aware of any issues on some imx6 devices in 2018.09? The
hummingboard2 (imx6q) hangs for me just after the output below, even
with the above PR, it works fine with a imx6sx device (udoo neo). I'm
sure I've seen something on the list that might be related but I can't
find it.

Sorry for picking this up so late in the cycle.

Peter

U-Boot SPL 2018.09-rc3 (Sep 05 2018 - 20:28:15 +0000)
Trying to boot from MMC1


U-Boot 2018.09-rc3 (Sep 05 2018 - 20:28:15 +0000)

CPU:   Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU:   Extended Commercial temperature grade (-20C to 105C) at 25C
Reset cause: POR
Board: MX6 HummingBoard2 (som rev 1.5)
DRAM:  2 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

No panel detected: default to HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial