[U-Boot] [PULL] Please pull u-boot-imx

[Stefano Babic]

Hi Peter,

On 06/09/2018 11:23, Peter Robinson wrote:
> Hi Stefano,
> 
>> a new PR. I dropped the patches causing breakages on PowerPC boards, as
>> well as the issue on GE boards. It ran on travis successfully.
>>
>>
>> The following changes since commit 11ed312896c5f5814064c5d45dcb2f53dc121437:
>>
>>   configs: am57xx: change default board name to beagle_x15 (2018-08-26
>> 12:26:16 -0400)
>>
>> are available in the Git repository at:
>>
>>   git://www.denx.de/git/u-boot-imx.git master
>>
>> for you to fetch changes up to c1d1543ebc6e1fb026d0d7ac96d865faa7567555:
>>
>>   mx7dsabresd: Add the qspi target to the list of supported defconfigs
>> (2018-09-04 08:47:23 +0200)
>>
>> ----------------------------------------------------------------
>> Alex Kiernan (1):
>>       Cleanup CONFIG_BOOTDELAY on cl-som-imx7
>>
>> Anson Huang (3):
>>       imx: mx7: psci: improve cpu hotplug flow
>>       imx: mx7: add gpc initialization for low power mode
>>       imx: mx7: add system suspend/resume support
>>
>> Fabio Estevam (1):
>>       mx7dsabresd: Add the qspi target to the list of supported defconfigs
>>
>> Martin Kaiser (1):
>>       watchdog: mx25: use the imx_watchdog driver for mx25
>>
>> Stefan Agner (2):
>>       board: toradex: common: fail gracefully on missing NAND chip
>>       colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support
>>
>> Stefano Babic (1):
>>       imx: missing CONFIG_MII in mx7dsabresd_qspi_defconfig
>>
>> Ye Li (6):
>>       imx: imx6sx-sdb: Enable DM QSPI driver
>>       imx: imx6sx-sabreauto: convert to use DM QSPI driver
>>       imx: imx7d-sdb: Add DM QSPI support
>>       dts: imx6ul: Update alias to support DM
>>       dts: imx6ul_evk: Add DTS files for 14x14 EVK and 9x9 EVK boards
>>       imx: imx6ul_evk: Enable DM driver for iMX6UL EVK u-boot
> 
> Are you aware of any issues on some imx6 devices in 2018.09?

No.

> The
> hummingboard2 (imx6q) hangs for me just after the output below, even
> with the above PR, it works fine with a imx6sx device (udoo neo). I'm
> sure I've seen something on the list that might be related but I can't
> find it.

:-(

> 
> Sorry for picking this up so late in the cycle.

I can just try to test on another mx6q boar if I get enough time, but of
course this is not a great test.

Regards,
Stefano

> 
> Peter
> 
> U-Boot SPL 2018.09-rc3 (Sep 05 2018 - 20:28:15 +0000)
> Trying to boot from MMC1
> 
> 
> U-Boot 2018.09-rc3 (Sep 05 2018 - 20:28:15 +0000)
> 
> CPU:   Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
> CPU:   Extended Commercial temperature grade (-20C to 105C) at 25C
> Reset cause: POR
> Board: MX6 HummingBoard2 (som rev 1.5)
> DRAM:  2 GiB
> MMC:   FSL_SDHC: 0, FSL_SDHC: 1
> Loading Environment from MMC... *** Warning - bad CRC, using default environment
> 
> No panel detected: default to HDMI
> Display: HDMI (1024x768)
> In:    serial
> Out:   serial
> Err:   serial
> 


-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================