[U-Boot] [PATCH] imx: Add variscite DART-6UL Evaluation Kit
Parthiban Nallathambi
parthitce at gmail.com
Wed Apr 17 22:04:09 UTC 2019
Port for the DART-6UL Evaluation Kit SBC. Based on the variscite
DART-6UL iMX6ULL SoM.
CPU: Freescale i.MX6ULL rev1.1 900 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 43C
Reset cause: POR
Model: Variscite DART-6UL Evaluation Kit
Board: Variscite DART-6UL Evaluation Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial at 02020000
Out: serial at 02020000
Err: serial at 02020000
Net: FEC0
Working:
- Eth0
- i2c
- MMC/SD
- eMMC
- USB host
- UART 1
Note: LCDIF porting needs DM_VIDEO
https://lists.denx.de/pipermail/u-boot/2019-April/365506.html
Signed-off-by: Parthiban Nallathambi <parthitce at gmail.com>
---
arch/arm/Kconfig | 1 +
arch/arm/dts/Makefile | 1 +
arch/arm/dts/imx6ull-dart-6ul.dts | 39 ++++
arch/arm/dts/imx6ull-dart-6ul.dtsi | 261 +++++++++++++++++++++++++++
arch/arm/mach-imx/mx6/Kconfig | 12 ++
board/variscite/dart_6ul/Kconfig | 12 ++
board/variscite/dart_6ul/MAINTAINERS | 8 +
board/variscite/dart_6ul/Makefile | 4 +
board/variscite/dart_6ul/README | 41 +++++
board/variscite/dart_6ul/dart_6ul.c | 228 +++++++++++++++++++++++
board/variscite/dart_6ul/spl.c | 215 ++++++++++++++++++++++
configs/variscite_dart6ul_defconfig | 55 ++++++
include/configs/dart_6ul.h | 131 ++++++++++++++
13 files changed, 1008 insertions(+)
create mode 100644 arch/arm/dts/imx6ull-dart-6ul.dts
create mode 100644 arch/arm/dts/imx6ull-dart-6ul.dtsi
create mode 100644 board/variscite/dart_6ul/Kconfig
create mode 100644 board/variscite/dart_6ul/MAINTAINERS
create mode 100644 board/variscite/dart_6ul/Makefile
create mode 100644 board/variscite/dart_6ul/README
create mode 100644 board/variscite/dart_6ul/dart_6ul.c
create mode 100644 board/variscite/dart_6ul/spl.c
create mode 100644 configs/variscite_dart6ul_defconfig
create mode 100644 include/configs/dart_6ul.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 4640f3b3bd..c20866c86a 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1635,6 +1635,7 @@ source "board/tcl/sl50/Kconfig"
source "board/ucRobotics/bubblegum_96/Kconfig"
source "board/birdland/bav335x/Kconfig"
source "board/toradex/colibri_pxa270/Kconfig"
+source "board/variscite/dart_6ul/Kconfig"
source "board/vscom/baltos/Kconfig"
source "board/woodburn/Kconfig"
source "board/xilinx/Kconfig"
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 0aee8dfde0..6fb545dc9f 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -549,6 +549,7 @@ dtb-$(CONFIG_MX6UL) += \
dtb-$(CONFIG_MX6ULL) += \
imx6ull-14x14-evk.dtb \
imx6ull-colibri.dtb \
+ imx6ull-dart-6ul.dtb
dtb-$(CONFIG_ARCH_MX6) += \
imx6-colibri.dtb
diff --git a/arch/arm/dts/imx6ull-dart-6ul.dts b/arch/arm/dts/imx6ull-dart-6ul.dts
new file mode 100644
index 0000000000..4cab1a048b
--- /dev/null
+++ b/arch/arm/dts/imx6ull-dart-6ul.dts
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce at gmail.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull.dtsi"
+#include "imx6ull-dart-6ul.dtsi"
+
+/ {
+ model = "Variscite DART-6UL Evaluation Kit";
+ compatible = "variscite,imx6ull-dart-6ul", "fsl,imx6ull";
+};
+
+&usdhc2 {
+ status = "okay";
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1_id>;
+ dr_mode = "otg";
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_usb_otg1_id: usbotg1idgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+};
diff --git a/arch/arm/dts/imx6ull-dart-6ul.dtsi b/arch/arm/dts/imx6ull-dart-6ul.dtsi
new file mode 100644
index 0000000000..e96669f493
--- /dev/null
+++ b/arch/arm/dts/imx6ull-dart-6ul.dtsi
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce at gmail.com>
+ */
+
+/ {
+ model = "Variscite DART-6UL i.MX6 Ultra Low Lite SOM";
+ compatible = "variscite,imx6ull-dart-6ul", "fsl,imx6ull";
+
+ memory {
+ reg = <0x80000000 0x20000000>;
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ status = "okay";
+
+ mdio1: mdio1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy at 1 {
+ reg = <1>;
+ micrel,led-mode = <1>;
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio2: mdio2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy at 2 {
+ reg = <2>;
+ micrel,led-mode = <1>;
+ };
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ fsl,no-blockmark-swap;
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "uboot";
+ reg = <0x0 0x400000>;
+ };
+
+ partition at 400000 {
+ label = "uboot-env";
+ reg = <0x400000 0x100000>;
+ };
+
+ partition at 500000 {
+ label = "root";
+ reg = <0x500000 0x0>;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ scl-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ eeprom at 50 {
+ compatible = "cat,24c32";
+ reg = <0x50>;
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ #pwm-cells = <3>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ bus-width = <0x4>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ keep-power-in-suspend;
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0X1b0b0
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
+ MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0X1b0b0
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_DQS__RAWNAND_DQS 0x0b0b1
+ MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
+ MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
+ MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1
+ MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
+ MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1
+ MX6UL_PAD_NAND_CE1_B__RAWNAND_CE1_B 0x0b0b1
+ MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1
+ MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1
+ MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1
+ MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1
+ MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1
+ MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1
+ MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1
+ MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1
+ MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1
+ MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1
+ >;
+ };
+
+ pinctrl_i2c1: i2cgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1grp_gpio {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
+ MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
+ >;
+ };
+
+ pinctrl_i2c2: i2cgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
+ MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2grp_gpio {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b8b0
+ MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x1b8b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__GPIO3_IO05 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
+
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
+ >;
+ };
+};
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index e782859b1e..f513c4c06f 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -161,6 +161,18 @@ config TARGET_COLIBRI_IMX6ULL
select DM_THERMAL
select MX6ULL
+config TARGET_DART_6UL
+ bool "Variscite imx6ULL dart(DART-SOM-6ULL)"
+ select MX6ULL
+ select DM
+ select DM_ETH
+ select DM_GPIO
+ select DM_I2C
+ select DM_MMC
+ select DM_SERIAL
+ select DM_THERMAL
+ select SUPPORT_SPL
+
config TARGET_DHCOMIMX6
bool "dh_imx6"
select BOARD_EARLY_INIT_F
diff --git a/board/variscite/dart_6ul/Kconfig b/board/variscite/dart_6ul/Kconfig
new file mode 100644
index 0000000000..1765af1d82
--- /dev/null
+++ b/board/variscite/dart_6ul/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_DART_6UL
+
+config SYS_BOARD
+ default "dart_6ul"
+
+config SYS_VENDOR
+ default "variscite"
+
+config SYS_CONFIG_NAME
+ default "dart_6ul"
+
+endif
diff --git a/board/variscite/dart_6ul/MAINTAINERS b/board/variscite/dart_6ul/MAINTAINERS
new file mode 100644
index 0000000000..339f93fa66
--- /dev/null
+++ b/board/variscite/dart_6ul/MAINTAINERS
@@ -0,0 +1,8 @@
+MX6UL_DART BOARD
+M: Parthiban Nallathambi <parthitce at gmail.com>
+S: Maintained
+F: arch/arm/dts/imx6ull-dart-6ul.dts
+F: arch/arm/dts/imx6ull-dart-6ul.dtsi
+F: board/variscite/dart_6ul/
+F: configs/variscite_dart6ul_defconfig
+F: include/configs/dart_6ul.h
diff --git a/board/variscite/dart_6ul/Makefile b/board/variscite/dart_6ul/Makefile
new file mode 100644
index 0000000000..48aa361bf2
--- /dev/null
+++ b/board/variscite/dart_6ul/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y := dart_6ul.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
diff --git a/board/variscite/dart_6ul/README b/board/variscite/dart_6ul/README
new file mode 100644
index 0000000000..d76b997e22
--- /dev/null
+++ b/board/variscite/dart_6ul/README
@@ -0,0 +1,41 @@
+How to use U-Boot on variscite DART-6UL Evaluation Kit
+------------------------------------------------------
+
+- Configure and build U-Boot for DART-6UL iMX6ULL:
+
+ $ make mrproper
+ $ make variscite_dart6ul_defconfig
+ $ make
+
+ This will generate SPL and u-boot-dtb.img images.
+
+Boot from MMC/SD:
+- The SPL and u-boot-dtb.img images need to be flashed into the micro SD card:
+
+ $ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+ $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync
+
+- Boot mode settings:
+
+ Boot switch position: SW1 -> 0
+ SW2 -> 0
+
+Boot from eMMC:
+- if bootpart is not enabled by default, to enable under Linux
+ echo 0 >/sys/block/mmcblk1boot0/force_ro
+ mmc bootpart enable 1 1 /dev/mmcblk1boot0
+
+- Flash the SPL and u-boot-dtb.img to mmcblk1boot0
+ $ sudo dd if=SPL of=/dev/mmcblk1boot0 bs=1k seek=1; sync
+ $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk1boot0 bs=1k seek=69; sync
+
+- Boot mode settings:
+
+ Boot switch position: SW1 -> 0
+ SW2 -> 1
+
+- Connect the Serial cable to UART0 and the PC for the console.
+
+- Insert the micro SD card in the board and power it up.
+
+- U-Boot messages should come up.
diff --git a/board/variscite/dart_6ul/dart_6ul.c b/board/variscite/dart_6ul/dart_6ul.c
new file mode 100644
index 0000000000..4765595af1
--- /dev/null
+++ b/board/variscite/dart_6ul/dart_6ul.c
@@ -0,0 +1,228 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015-2019 Variscite Ltd.
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce at gmail.com>
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc.h>
+#include <linux/bitops.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+
+ return 0;
+}
+
+#ifdef CONFIG_NAND_MXS
+#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
+#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
+ PAD_CTL_SRE_FAST)
+#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
+static iomux_v3_cfg_t const nand_pads[] = {
+ MX6_PAD_NAND_DATA00__RAWNAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_DATA01__RAWNAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_DATA02__RAWNAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_DATA03__RAWNAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_DATA04__RAWNAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_DATA05__RAWNAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_DATA06__RAWNAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_DATA07__RAWNAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_CLE__RAWNAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_ALE__RAWNAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_RE_B__RAWNAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_WE_B__RAWNAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_READY_B__RAWNAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NAND_DQS__RAWNAND_DQS | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+};
+
+static void setup_gpmi_nand(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ /* config gpmi nand iomux */
+ imx_iomux_v3_setup_multiple_pads(nand_pads, ARRAY_SIZE(nand_pads));
+
+ clrbits_le32(&mxc_ccm->CCGR4,
+ MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+
+ /*
+ * config gpmi and bch clock to 100 MHz
+ * bch/gpmi select PLL2 PFD2 400M
+ * 100M = 400M / 4
+ */
+ clrbits_le32(&mxc_ccm->cscmr1,
+ MXC_CCM_CSCMR1_BCH_CLK_SEL |
+ MXC_CCM_CSCMR1_GPMI_CLK_SEL);
+ clrsetbits_le32(&mxc_ccm->cscdr1,
+ MXC_CCM_CSCDR1_BCH_PODF_MASK |
+ MXC_CCM_CSCDR1_GPMI_PODF_MASK,
+ (3 << MXC_CCM_CSCDR1_BCH_PODF_OFFSET) |
+ (3 << MXC_CCM_CSCDR1_GPMI_PODF_OFFSET));
+
+ /* enable gpmi and bch clock gating */
+ setbits_le32(&mxc_ccm->CCGR4,
+ MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+
+ /* enable apbh clock gating */
+ setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
+ PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | \
+ PAD_CTL_SRE_FAST)
+#define MDIO_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
+ PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST | \
+ PAD_CTL_ODE)
+/*
+ * pin conflicts for fec1 and fec2, GPIO1_IO06 and GPIO1_IO07 can only
+ * be used for ENET1 or ENET2, cannot be used for both.
+ */
+static iomux_v3_cfg_t const fec1_pads[] = {
+ MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+ MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+ MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const fec2_pads[] = {
+ MX6_PAD_GPIO1_IO06__ENET2_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+ MX6_PAD_GPIO1_IO07__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET2_TX_EN__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+ MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET2_RX_ER__ENET2_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET2_RX_EN__ENET2_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_fec(int fec_id)
+{
+ if (fec_id == 0)
+ imx_iomux_v3_setup_multiple_pads(fec1_pads,
+ ARRAY_SIZE(fec1_pads));
+ else
+ imx_iomux_v3_setup_multiple_pads(fec2_pads,
+ ARRAY_SIZE(fec2_pads));
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int ret = 0;
+
+ ret = fecmxc_initialize_multi(bis, CONFIG_FEC_ENET_DEV,
+ CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+
+#if defined(CONFIG_CI_UDC) && defined(CONFIG_USB_ETHER)
+ /* USB Ethernet Gadget */
+ usb_eth_initialize(bis);
+#endif
+ return ret;
+}
+
+static int setup_fec(int fec_id)
+{
+ struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ int ret;
+
+ if (fec_id == 0) {
+ /*
+ * Use 50M anatop loopback REF_CLK1 for ENET1,
+ * clear gpr1[13], set gpr1[17].
+ */
+ clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+ IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+ } else {
+ /*
+ * Use 50M anatop loopback REF_CLK2 for ENET2,
+ * clear gpr1[14], set gpr1[18].
+ */
+ clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
+ IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+ }
+
+ ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
+ if (ret)
+ return ret;
+
+ enable_enet_clk(1);
+
+ return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ /*
+ * Defaults + Enable status LEDs (LED1: Activity, LED0: Link) & select
+ * 50 MHz RMII clock mode.
+ */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+#endif /* CONFIG_FEC_MXC */
+
+int board_early_init_f(void)
+{
+ setup_iomux_fec(CONFIG_FEC_ENET_DEV);
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_FEC_MXC
+ setup_fec(CONFIG_FEC_ENET_DEV);
+#endif
+
+#ifdef CONFIG_NAND_MXS
+ setup_gpmi_nand();
+#endif
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: Variscite DART-6UL Evaluation Kit\n");
+
+ return 0;
+}
diff --git a/board/variscite/dart_6ul/spl.c b/board/variscite/dart_6ul/spl.c
new file mode 100644
index 0000000000..f7e6ab6325
--- /dev/null
+++ b/board/variscite/dart_6ul/spl.c
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015-2019 Variscite Ltd.
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce at gmail.com>
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/arch/clock.h>
+#include <asm/io.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/crm_regs.h>
+#include <fsl_esdhc.h>
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+ .grp_addds = 0x00000030,
+ .grp_ddrmode_ctl = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_ctlds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_ddrpke = 0x00000000,
+ .grp_ddrmode = 0x00020000,
+ .grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+ .dram_dqm0 = 0x00000030,
+ .dram_dqm1 = 0x00000030,
+ .dram_ras = 0x00000030,
+ .dram_cas = 0x00000030,
+ .dram_odt0 = 0x00000030,
+ .dram_odt1 = 0x00000030,
+ .dram_sdba2 = 0x00000000,
+ .dram_sdclk_0 = 0x00000008,
+ .dram_sdqs0 = 0x00000038,
+ .dram_sdqs1 = 0x00000030,
+ .dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+ .p0_mpwldectrl0 = 0x00000000,
+ .p0_mpdgctrl0 = 0x414C0158,
+ .p0_mprddlctl = 0x40403A3A,
+ .p0_mpwrdlctl = 0x40405A56,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+ .dsize = 0,
+ .cs_density = 20,
+ .ncs = 1,
+ .cs1_mirror = 0,
+ .rtt_wr = 2,
+ .rtt_nom = 1, /* RTT_Nom = RZQ/2 */
+ .walat = 1, /* Write additional latency */
+ .ralat = 5, /* Read additional latency */
+ .mif3_mode = 3, /* Command prediction working mode */
+ .bi_on = 1, /* Bank interleaving enabled */
+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+ .mem_speed = 800,
+ .density = 4,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 15,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1375,
+ .trcmin = 4875,
+ .trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ writel(0xFFFFFFFF, &ccm->CCGR0);
+ writel(0xFFFFFFFF, &ccm->CCGR1);
+ writel(0xFFFFFFFF, &ccm->CCGR2);
+ writel(0xFFFFFFFF, &ccm->CCGR3);
+ writel(0xFFFFFFFF, &ccm->CCGR4);
+ writel(0xFFFFFFFF, &ccm->CCGR5);
+ writel(0xFFFFFFFF, &ccm->CCGR6);
+ writel(0xFFFFFFFF, &ccm->CCGR7);
+ /* Enable Audio Clock for SOM codec */
+ writel(0x01130100, (long *)CCM_CCOSR);
+}
+
+static void spl_dram_init(void)
+{
+ mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+ mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+ MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#ifndef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+#endif
+
+static struct fsl_esdhc_cfg usdhc_cfg[] = {
+ {
+ .esdhc_base = USDHC1_BASE_ADDR,
+ .max_bus_width = 4,
+ },
+#ifndef CONFIG_NAND_MXS
+ {
+ .esdhc_base = USDHC2_BASE_ADDR,
+ .max_bus_width = 8,
+ },
+#endif
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ int i, ret;
+
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ SETUP_IOMUX_PADS(usdhc1_pads);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+#ifndef CONFIG_NAND_MXS
+ case 1:
+ SETUP_IOMUX_PADS(usdhc2_pads);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ break;
+#endif
+ default:
+ printf("Warning - USDHC%d controller not supporting\n",
+ i + 1);
+ return 0;
+ }
+
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret) {
+ printf("Warning: failed to initialize mmc dev %d\n", i);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+void board_init_f(ulong dummy)
+{
+ /* setup AIPS and disable watchdog */
+ arch_cpu_init();
+
+ ccgr_init();
+
+ /* setup GP timer */
+ timer_init();
+
+ setup_iomux_uart();
+
+ /* iomux and setup of i2c */
+ board_early_init_f();
+
+ /* UART clocks enabled and gd valid - init serial console */
+ preloader_console_init();
+
+ /* DDR initialization */
+ spl_dram_init();
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ /* load/boot image from boot device */
+ board_init_r(NULL, 0);
+}
diff --git a/configs/variscite_dart6ul_defconfig b/configs/variscite_dart6ul_defconfig
new file mode 100644
index 0000000000..a1cdd05619
--- /dev/null
+++ b/configs/variscite_dart6ul_defconfig
@@ -0,0 +1,55 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x86000000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_TARGET_DART_6UL=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL=y
+# CONFIG_CMD_DEKBLOB is not set
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_NR_DRAM_BANKS=8
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_BOOTDELAY=3
+# CONFIG_USE_BOOTCOMMAND is not set
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_USB_HOST_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+# CONFIG_RANDOM_UUID is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_NET=y
+# CONFIG_ISO_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6ull-dart-6ul"
+CONFIG_DM_I2C_GPIO=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_FSL_ESDHC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_MXC_UART=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Variscite"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_LZO=y
diff --git a/include/configs/dart_6ul.h b/include/configs/dart_6ul.h
new file mode 100644
index 0000000000..fb1b899d71
--- /dev/null
+++ b/include/configs/dart_6ul.h
@@ -0,0 +1,131 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Board configuration file for Variscite DART-6UL Evaluation Kit
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce at gmail.com>
+ */
+#ifndef __DART_6UL_H
+#define __DART_6UL_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* SPL options */
+#include "imx6_spl.h"
+
+/* NAND pin conflicts with usdhc2 */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_SYS_FSL_USDHC_NUM 1
+#else
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+#endif
+
+#ifdef CONFIG_CMD_NET
+#define CONFIG_FEC_ENET_DEV 0
+
+#if (CONFIG_FEC_ENET_DEV == 0)
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR 0x1
+#define CONFIG_FEC_XCV_TYPE RMII
+#define CONFIG_ETHPRIME "eth0"
+#elif (CONFIG_FEC_ENET_DEV == 1)
+#define IMX_FEC_BASE ENET2_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR 0x3
+#define CONFIG_FEC_XCV_TYPE RMII
+#define CONFIG_ETHPRIME "eth1"
+#endif
+#endif
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
+
+/* Environment settings */
+#define CONFIG_ENV_SIZE SZ_8K
+#define CONFIG_ENV_OFFSET (14 * SZ_64K)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_OFFSET_REDUND \
+ (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+/* Environment in SD */
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_SYS_MMC_ENV_PART 0
+#define MMC_ROOTFS_DEV 0
+#define MMC_ROOTFS_PART 2
+
+/* Console configs */
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_FSL_USDHC
+
+#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+/* I2C configs */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_SPEED 100000
+#endif
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x8000000)
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
+
+/* Physical Memory Map */
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE SZ_512M
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+
+#define CONFIG_IMX_THERMAL
+
+#define ENV_MMC \
+ "mmcdev=" __stringify(MMC_ROOTFS_DEV) "\0" \
+ "mmcpart=" __stringify(MMC_ROOTFS_PART) "\0" \
+ "fitpart=1\0" \
+ "bootdelay=3\0" \
+ "silent=1\0" \
+ "optargs=rw rootwait\0" \
+ "mmcautodetect=yes\0" \
+ "mmcrootfstype=ext4\0" \
+ "mmcfit_name=fitImage\0" \
+ "mmcloadfit=fatload mmc ${mmcdev}:${fitpart} ${fit_addr} " \
+ "${mmcfit_name}\0" \
+ "mmcargs=setenv bootargs " \
+ "root=/dev/mmcblk${mmcdev}p${mmcpart} ${optargs} " \
+ "console=${console} rootfstype=${mmcrootfstype}\0" \
+ "mmc_mmc_fit=run mmcloadfit;run mmcargs addcon; bootm ${fit_addr}\0" \
+
+/* Default environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fdt_high=0xffffffff\0" \
+ "console=ttymxc0,115200n8\0" \
+ "addcon=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \
+ "fit_addr=0x82000000\0" \
+ ENV_MMC
+
+#define CONFIG_BOOTCOMMAND "run mmc_mmc_fit"
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(MMC, mmc, 1) \
+ func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+#endif /* __DART_6UL_H */
--
2.17.2
More information about the U-Boot
mailing list