[RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion

[Tom Rini]

On Fri, Dec 06, 2019 at 06:23:09PM +0100, Lukasz Majewski wrote:
> Hi Igor,
> 
> > Hi Stefano
> > 
> > On Fri, Dec 6, 2019 at 6:24 PM Igor Opaniuk <igor.opaniuk at gmail.com>
> > wrote:
> > >
> > > From: Igor Opaniuk <igor.opaniuk at toradex.com>
> > >
> > > Not all CONFIG_FSL_ESDHC defines were properly replaced with
> > > CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on
> > > Colibri iMX6 SoMs.
> > >
> > > U-boot is stuck after this message:
> > > Commercial temperature grade DDR3 timings, 64bit bus width.
> > > Trying to boot from MMC1
> > >
> > > Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms")
> > > Signed-off-by: Igor Opaniuk <igor.opaniuk at toradex.com>
> > > ---
> > >
> > >  board/toradex/colibri_imx6/colibri_imx6.c | 4 ++--
> > >  1 file changed, 2 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/board/toradex/colibri_imx6/colibri_imx6.c
> > > b/board/toradex/colibri_imx6/colibri_imx6.c index
> > > ad40b589c1..44173dde1f 100644 ---
> > > a/board/toradex/colibri_imx6/colibri_imx6.c +++
> > > b/board/toradex/colibri_imx6/colibri_imx6.c @@ -83,7 +83,7 @@
> > > iomux_v3_cfg_t const uart1_pads[] = {
> > > MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), };
> > >
> > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD)
> > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD)
> > >  /* Colibri MMC */
> > >  iomux_v3_cfg_t const usdhc1_pads[] = {
> > >         MX6_PAD_SD1_CLK__SD1_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > > @@ -304,7 +304,7 @@ int board_ehci_hcd_init(int port)
> > >  }
> > >  #endif
> > >
> > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD)
> > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD)
> > >  /* use the following sequence: eMMC, MMC */
> > >  struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = {
> > >         {USDHC3_BASE_ADDR},
> > > --
> > > 2.17.1
> > >  
> > 
> > I've just found the same fix [1] but from Ricardo with Awaiting
> > upstream status in patchwork (I thought that he has fixed just Apalis
> > iMX6), but seems the patch was
> > lost somewhere, as I can not find it nor in u-boot-imx/next neither
> > in u-boot-imx/master branches.
> 
> Thanks for providing the fix (at least for the Toradex boards)
> 
> And I do guess that more i.MX6 boards are affected ...

I think there's just one other.  The imx8qm_rom7720_a1 references
CONFIG_FSL_ESDHC still, but I don't see any other i.MX8 platforms doing
anything with the symbol to compare with.

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20191206/9b1d842c/attachment.sig>