[PATCH] drivers: net: fsl_enetc: use write_hwaddr()

Michael Walle michael at walle.cc
Wed Dec 18 17:47:31 CET 2019


Intead of setting the MAC address in enetc_start() use the proper
write_hwaddr(). U-Boot takes care of the random MAC address, too. Also,
this will correctly handle ethNmacskip etc.

Signed-off-by: Michael Walle <michael at walle.cc>
---
 drivers/net/fsl_enetc.c | 17 ++++++++---------
 1 file changed, 8 insertions(+), 9 deletions(-)

diff --git a/drivers/net/fsl_enetc.c b/drivers/net/fsl_enetc.c
index e86f3dddb5..1949530460 100644
--- a/drivers/net/fsl_enetc.c
+++ b/drivers/net/fsl_enetc.c
@@ -272,14 +272,19 @@ static int enetc_remove(struct udevice *dev)
 	return 0;
 }
 
-/* ENETC Port MAC address registers, accepts big-endian format */
-static void enetc_set_primary_mac_addr(struct enetc_priv *priv, const u8 *addr)
+static int enetc_write_hwaddr(struct udevice *dev)
 {
+	struct eth_pdata *plat = dev_get_platdata(dev);
+	struct enetc_priv *priv = dev_get_priv(dev);
+	u8 *addr = plat->enetaddr;
+
 	u16 lower = *(const u16 *)(addr + 4);
 	u32 upper = *(const u32 *)addr;
 
 	enetc_write_port(priv, ENETC_PSIPMAR0, upper);
 	enetc_write_port(priv, ENETC_PSIPMAR1, lower);
+
+	return 0;
 }
 
 /* Configure port parameters (# of rings, frame size, enable port) */
@@ -410,7 +415,6 @@ static void enetc_setup_rx_bdr(struct udevice *dev)
  */
 static int enetc_start(struct udevice *dev)
 {
-	struct eth_pdata *plat = dev_get_platdata(dev);
 	struct enetc_priv *priv = dev_get_priv(dev);
 
 	/* reset and enable the PCI device */
@@ -418,12 +422,6 @@ static int enetc_start(struct udevice *dev)
 	dm_pci_clrset_config16(dev, PCI_COMMAND, 0,
 			       PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
 
-	if (!is_valid_ethaddr(plat->enetaddr)) {
-		enetc_dbg(dev, "invalid MAC address, generate random ...\n");
-		net_random_ethaddr(plat->enetaddr);
-	}
-	enetc_set_primary_mac_addr(priv, plat->enetaddr);
-
 	enetc_enable_si_port(priv);
 
 	/* setup Tx/Rx buffer descriptors */
@@ -549,6 +547,7 @@ static const struct eth_ops enetc_ops = {
 	.send	= enetc_send,
 	.recv	= enetc_recv,
 	.stop	= enetc_stop,
+	.write_hwaddr = enetc_write_hwaddr,
 };
 
 U_BOOT_DRIVER(eth_enetc) = {
-- 
2.20.1



More information about the U-Boot mailing list