[U-Boot] [PATCH v2 2/9] ARM: rockchip: rk3188: Remove the pinctrl setup and enable uart at SPL

[David Wu]

When the boot ROM sets up MMC we don't need to do it again. Remove the
MMC setup code entirely, but we also need to enable uart for debug message.

Signed-off-by: David Wu <david.wu at rock-chips.com>
---

Changes in v2: None

 arch/arm/mach-rockchip/rk3188-board-spl.c | 41 ++---------------------
 1 file changed, 2 insertions(+), 39 deletions(-)

diff --git a/arch/arm/mach-rockchip/rk3188-board-spl.c b/arch/arm/mach-rockchip/rk3188-board-spl.c
index 3c6c3d3c09..a5e4d39cb7 100644
--- a/arch/arm/mach-rockchip/rk3188-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3188-board-spl.c
@@ -120,7 +120,7 @@ void board_debug_uart_init(void)
 
 void board_init_f(ulong dummy)
 {
-	struct udevice *pinctrl, *dev;
+	struct udevice *dev;
 	int ret;
 
 #define EARLY_UART
@@ -134,10 +134,7 @@ void board_init_f(ulong dummy)
 	 * printascii("string");
 	 */
 	debug_uart_init();
-	printch('s');
-	printch('p');
-	printch('l');
-	printch('\n');
+	printascii("U-Boot SPL board init");
 #endif
 
 #ifdef CONFIG_ROCKCHIP_USB_UART
@@ -171,12 +168,6 @@ void board_init_f(ulong dummy)
 		return;
 	}
 
-	ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
-	if (ret) {
-		debug("Pinctrl init failed: %d\n", ret);
-		return;
-	}
-
 	ret = uclass_get_device(UCLASS_RAM, 0, &dev);
 	if (ret) {
 		debug("DRAM init failed: %d\n", ret);
@@ -214,7 +205,6 @@ static int setup_led(void)
 
 void spl_board_init(void)
 {
-	struct udevice *pinctrl;
 	int ret;
 
 	ret = setup_led();
@@ -223,36 +213,9 @@ void spl_board_init(void)
 		hang();
 	}
 
-	ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
-	if (ret) {
-		debug("%s: Cannot find pinctrl device\n", __func__);
-		goto err;
-	}
-
-#ifdef CONFIG_SPL_MMC_SUPPORT
-	ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD);
-	if (ret) {
-		debug("%s: Failed to set up SD card\n", __func__);
-		goto err;
-	}
-#endif
-
-	/* Enable debug UART */
-	ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_UART_DBG);
-	if (ret) {
-		debug("%s: Failed to set up console UART\n", __func__);
-		goto err;
-	}
-
 	preloader_console_init();
 #if CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM)
 	back_to_bootrom(BROM_BOOT_NEXTSTAGE);
 #endif
 	return;
-
-err:
-	printf("spl_board_init: Error %d\n", ret);
-
-	/* No way to report error here */
-	hang();
 }
-- 
2.19.1