[U-Boot] [PATCH 1/2] mips: spi: mscc: Add fast bitbang SPI driver
Lars Povlsen
lars.povlsen at microchip.com
Fri Jan 4 09:47:10 UTC 2019
From: Lars Povlsen <lars.povlsen at microsemi.com>
This patch add a new SPI driver for MSCC SOCs that does not sport the
designware SPI hardware controller.
Performance gain: 7.664 seconds vs. 17.633 for 1 Mbyte write -
measured on a Luton10 with a m25p128 NOR flash.
Signed-off-by: Lars Povlsen <lars.povlsen at microsemi.com>
---
MAINTAINERS | 1 +
configs/mscc_luton_defconfig | 3 +-
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/mscc_bb_spi.c | 258 +++++++++++++++++++++++++++++++++++
5 files changed, 269 insertions(+), 1 deletion(-)
create mode 100644 drivers/spi/mscc_bb_spi.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 494962e9b3..0cee99ef56 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -524,6 +524,7 @@ F: arch/mips/dts/ocelot*
F: board/mscc/
F: configs/mscc*
F: drivers/gpio/mscc_sgpio.c
+F: drivers/spi/mscc_bb_spi.c
F: include/configs/vcoreiii.h
MIPS JZ4780
diff --git a/configs/mscc_luton_defconfig b/configs/mscc_luton_defconfig
index 65f0672c1e..d48a93a2a5 100644
--- a/configs/mscc_luton_defconfig
+++ b/configs/mscc_luton_defconfig
@@ -34,6 +34,7 @@ CONFIG_CMD_DHCP=y
# CONFIG_NET_TFTP_VARS is not set
# CONFIG_CMD_NFS is not set
CONFIG_CMD_PING=y
+CONFIG_CMD_TIME=y
CONFIG_CMD_MTDPARTS=y
CONFIG_MTDIDS_DEFAULT="nor0=spi_flash"
CONFIG_MTDPARTS_DEFAULT="mtdparts=spi_flash:1m(UBoot),256k(Env),256k(Env.bk),512k(Unused),6m(linux)"
@@ -66,5 +67,5 @@ CONFIG_DEBUG_UART_SHIFT=2
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
-CONFIG_SOFT_SPI=y
+CONFIG_MSCC_BB_SPI=y
CONFIG_LZMA=y
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index a7bb5b35c2..de4d62dd8f 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -294,6 +294,13 @@ config SOFT_SPI
Enable Soft SPI driver. This driver is to use GPIO simulate
the SPI protocol.
+config MSCC_BB_SPI
+ bool "MSCC bitbang SPI driver"
+ depends on SOC_VCOREIII
+ help
+ Enable MSCC bitbang SPI driver. This driver can be used on
+ MSCC SOCs.
+
config CF_SPI
bool "ColdFire SPI driver"
help
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 392a925795..4acec3ea17 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_MPC8XX_SPI) += mpc8xx_spi.o
obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
obj-$(CONFIG_MTK_QSPI) += mtk_qspi.o
obj-$(CONFIG_MT7621_SPI) += mt7621_spi.o
+obj-$(CONFIG_MSCC_BB_SPI) += mscc_bb_spi.o
obj-$(CONFIG_MVEBU_A3700_SPI) += mvebu_a3700_spi.o
obj-$(CONFIG_MXC_SPI) += mxc_spi.o
obj-$(CONFIG_MXS_SPI) += mxs_spi.o
diff --git a/drivers/spi/mscc_bb_spi.c b/drivers/spi/mscc_bb_spi.c
new file mode 100644
index 0000000000..e0ed2c9725
--- /dev/null
+++ b/drivers/spi/mscc_bb_spi.c
@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Microsemi SoCs spi driver
+ *
+ * License: Dual MIT/GPL
+ * Copyright (c) 2018 Microsemi Corporation
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <malloc.h>
+#include <spi.h>
+#include <dm.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <linux/delay.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct mscc_bb_platdata {
+ void __iomem *regs;
+ u32 deactivate_delay_us;
+};
+
+struct mscc_bb_priv {
+ void __iomem *regs;
+ bool cs_active; /* State flag as to whether CS is asserted */
+ int cs_num;
+ u32 svalue; /* Value to start transfer with */
+ u32 clk1; /* Clock value start */
+ u32 clk2; /* Clock value 2nd phase */
+};
+
+#define DELAY() \
+ asm volatile("nop; nop; nop; nop; nop; nop; nop; nop;" \
+ "nop; nop; nop; nop; nop; nop; nop; nop;" \
+ "nop; nop; nop; nop; nop; nop; nop; nop;")
+
+static int mscc_bb_spi_cs_activate(struct mscc_bb_priv *priv, int mode, int cs)
+{
+ if (!priv->cs_active) {
+ int cpha = mode & SPI_CPHA;
+ u32 cs_value;
+
+ priv->cs_num = cs;
+
+ if (cpha) {
+ /* Initial clock starts SCK=1 */
+ priv->clk1 = ICPU_SW_MODE_SW_SPI_SCK;
+ priv->clk2 = 0;
+ } else {
+ /* Initial clock starts SCK=0 */
+ priv->clk1 = 0;
+ priv->clk2 = ICPU_SW_MODE_SW_SPI_SCK;
+ }
+
+ /* Enable bitbang, SCK_OE, SDO_OE */
+ priv->svalue = (ICPU_SW_MODE_SW_PIN_CTRL_MODE | /* Bitbang */
+ ICPU_SW_MODE_SW_SPI_SCK_OE | /* SCK_OE */
+ ICPU_SW_MODE_SW_SPI_SDO_OE); /* SDO OE */
+
+ /* Add CS */
+ if (cs >= 0) {
+ cs_value =
+ ICPU_SW_MODE_SW_SPI_CS_OE(BIT(cs)) |
+ ICPU_SW_MODE_SW_SPI_CS(BIT(cs));
+ } else {
+ cs_value = 0;
+ }
+
+ priv->svalue |= cs_value;
+
+ /* Enable the CS in HW, Initial clock value */
+ writel(priv->svalue | priv->clk2, priv->regs);
+
+ priv->cs_active = true;
+ debug("Activated CS%d\n", priv->cs_num);
+ }
+
+ return 0;
+}
+
+static int mscc_bb_spi_cs_deactivate(struct mscc_bb_priv *priv, int deact_delay)
+{
+ if (priv->cs_active) {
+ /* Keep driving the CLK to its current value while
+ * actively deselecting CS.
+ */
+ u32 value = readl(priv->regs);
+
+ value &= ~ICPU_SW_MODE_SW_SPI_CS_M;
+ writel(value, priv->regs);
+ DELAY();
+
+ /* Stop driving the clock, but keep CS with nCS == 1 */
+ value &= ~ICPU_SW_MODE_SW_SPI_SCK_OE;
+ writel(value, priv->regs);
+
+ /* Deselect hold time delay */
+ if (deact_delay)
+ udelay(deact_delay);
+
+ /* Drop everything */
+ writel(0, priv->regs);
+
+ priv->cs_active = false;
+ debug("Deactivated CS%d\n", priv->cs_num);
+ }
+
+ return 0;
+}
+
+int mscc_bb_spi_claim_bus(struct udevice *dev)
+{
+ return 0;
+}
+
+int mscc_bb_spi_release_bus(struct udevice *dev)
+{
+ return 0;
+}
+
+int mscc_bb_spi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct udevice *bus = dev_get_parent(dev);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+ struct mscc_bb_platdata *bus_plat = dev_get_platdata(bus);
+ struct mscc_bb_priv *priv = dev_get_priv(bus);
+ u32 i, count;
+ const u8 *txd = dout;
+ u8 *rxd = din;
+
+ debug("spi_xfer: slave %s:%s cs%d mode %d, dout %p din %p bitlen %u\n",
+ dev->parent->name, dev->name, plat->cs, plat->mode, dout,
+ din, bitlen);
+
+ if (flags & SPI_XFER_BEGIN)
+ mscc_bb_spi_cs_activate(priv, plat->mode, plat->cs);
+
+ count = bitlen / 8;
+ for (i = 0; i < count; i++) {
+ u32 rx = 0, mask = 0x80, value;
+
+ while (mask) {
+ /* Initial condition: CLK is low. */
+ value = priv->svalue;
+ if (txd && txd[i] & mask)
+ value |= ICPU_SW_MODE_SW_SPI_SDO;
+
+ /* Drive data while taking CLK low. The device
+ * we're accessing will sample on the
+ * following rising edge and will output data
+ * on this edge for us to be sampled at the
+ * end of this loop.
+ */
+ writel(value | priv->clk1, priv->regs);
+
+ /* Wait for t_setup. All devices do have a
+ * setup-time, so we always insert some delay
+ * here. Some devices have a very long
+ * setup-time, which can be adjusted by the
+ * user through vcoreiii_device->delay.
+ */
+ DELAY();
+
+ /* Drive the clock high. */
+ writel(value | priv->clk2, priv->regs);
+
+ /* Wait for t_hold. See comment about t_setup
+ * above.
+ */
+ DELAY();
+
+ /* We sample as close to the next falling edge
+ * as possible.
+ */
+ value = readl(priv->regs);
+ if (value & ICPU_SW_MODE_SW_SPI_SDI)
+ rx |= mask;
+ mask >>= 1;
+ }
+ if (rxd) {
+ debug("Read 0x%02x\n", rx);
+ rxd[i] = (u8)rx;
+ }
+ debug("spi_xfer: byte %d/%d\n", i + 1, count);
+ }
+
+ debug("spi_xfer: done\n");
+
+ if (flags & SPI_XFER_END)
+ mscc_bb_spi_cs_deactivate(priv, bus_plat->deactivate_delay_us);
+
+ return 0;
+}
+
+int mscc_bb_spi_set_speed(struct udevice *dev, unsigned int speed)
+{
+ /* Accept any speed */
+ return 0;
+}
+
+int mscc_bb_spi_set_mode(struct udevice *dev, unsigned int mode)
+{
+ return 0;
+}
+
+static const struct dm_spi_ops mscc_bb_ops = {
+ .claim_bus = mscc_bb_spi_claim_bus,
+ .release_bus = mscc_bb_spi_release_bus,
+ .xfer = mscc_bb_spi_xfer,
+ .set_speed = mscc_bb_spi_set_speed,
+ .set_mode = mscc_bb_spi_set_mode,
+};
+
+static const struct udevice_id mscc_bb_ids[] = {
+ { .compatible = "mscc,luton-bb-spi" },
+ { }
+};
+
+static int mscc_bb_spi_probe(struct udevice *bus)
+{
+ struct mscc_bb_priv *priv = dev_get_priv(bus);
+ struct mscc_bb_platdata *plat = dev_get_platdata(bus);
+
+ debug("%s: loaded, priv %p, plat %p\n", __func__, priv, plat);
+
+ /* Initialize */
+ priv->regs = plat->regs;
+ priv->cs_active = false;
+
+ return 0;
+}
+
+static int mscc_bb_spi_ofdata_to_platdata(struct udevice *bus)
+{
+ struct mscc_bb_platdata *plat = dev_get_platdata(bus);
+
+ plat->regs = (void __iomem *)dev_read_addr(bus);
+
+ plat->deactivate_delay_us =
+ dev_read_u32_default(bus, "spi-deactivate-delay", 0);
+
+ return 0;
+}
+
+U_BOOT_DRIVER(mscc_bb) = {
+ .name = "mscc_bb",
+ .id = UCLASS_SPI,
+ .of_match = mscc_bb_ids,
+ .ops = &mscc_bb_ops,
+ .ofdata_to_platdata = mscc_bb_spi_ofdata_to_platdata,
+ .platdata_auto_alloc_size = sizeof(struct mscc_bb_platdata),
+ .priv_auto_alloc_size = sizeof(struct mscc_bb_priv),
+ .probe = mscc_bb_spi_probe,
+};
--
2.19.2
More information about the U-Boot
mailing list