[U-Boot] [PATCH v1 00/21] imx: vybrid: Update BK4 and PCM052 boards to only use DM/DTS

[Lukasz Majewski]

This patch series converts PCM052 and BK4 to use Driver Model and Device
Tree.
Some notable changes:
- The way how MAC address is read from fuses can now be adjusted
- DTS improvement/sync with kernel
- Using generic code instead of one from board

The output of u-boot boot:
U-Boot 2019.01-rc3-00076-gc149229be0 (Jan 14 2019 - 08:38:48 +0100)

CPU: Freescale Vybrid VF610 at 396 MHz
Reset cause: POWER ON RESET
Model: Liebherr (LVF) BK4 Vybrid Board
Board: BK4r1 (L333)
DRAM:  512 MiB
NAND:  1024 MiB
MMC:   FSL_SDHC: 0
Loading Environment from NAND... OK
In:    serial at 40028000
Out:   serial at 40028000
Err:   serial at 40028000
Net:   eth0: fec at 400d0000, eth1: fec at 400d1000
Enter passphrase to stop autoboot, booting in 3 seconds

Buildman CI:
./tools/buildman/buildman.py --branch=HEAD~3  vf610 mx6 vybrid --detail --verbose --show_errors --force-build --count=21 --output-dir=../BUILD/

Travis-CI:
https://travis-ci.org/lmajewski/u-boot-dfu/jobs/479284276
[omitting test_efi_selftest failure - as PCM052/BK4 is not supporting EFI]

U-boot master branch: SHA1: b3a69c246915bd704d6073bcf4614d6881c0da04



Lukasz Majewski (21):
  ARM: DTS: vybrid: Add vf-u-boot.dtsi to set 'u-boot,dm-pre-reloc' in
    soc
  net: FEC: Add compatible for vybrid (vf610) to reuse fec_mxc.c driver
  net: Kconfig: FEC: Add dependency on VF610
  vybrid: ddr: Extend vf610-pinfunc.h with DDR pads definitions
  vybrid: clock: Provide enable_i2c_clk() function for Vybrid
  vybrid: Define the imx_get_mac_from_fuse() as a __weak function
  pcm052: board: Remove "m4go" command as it is superseded by "bootaux"
  pcm052: board: vybrid: Update the board name for BK4 device
  ARM: DTS: vybrid: Update vf.dtsi file to descibe more vf610 hardware
  pcm052: board: cosmetic: Add copyright notice to pcm052.c
  ARM: DTS: Update pcm052 based dts files (bk4r1/pcm052.dts)
  defconfig: bk4/pcm052: Update bk4r1|pcm052_defconfig to support DM/DT
  config: pcm052: Use SZ_X{MK} from linux/sizes.h for
    include/configs/pcm052.h
  config: bk4: Update include/configs/bk4r1.h file
  pcm052: board: Remove in-board setup code (it is now replaced by DM
    setup)
  config: bk4: Update u-boot script to support recovery via SD card
  config: bk4: Update u-boot envs to support NOR memories initial setup
  pcm052: bk4: sdcard: Add support for SD card booting/recovery
  pcm052: board: Add code to setup LED default states
  pcm052: mac: Provide board specific imx_get_mac_from_fuse() function
  pcm052: bk4: Add board_phy_config() for BK4 to setup ksz8081 phy

 arch/arm/cpu/armv7/vf610/Kconfig           |   1 +
 arch/arm/cpu/armv7/vf610/generic.c         |  21 +-
 arch/arm/dts/bk4r1.dts                     | 108 +++++---
 arch/arm/dts/pcm052.dts                    |   6 +-
 arch/arm/dts/vf-u-boot.dtsi                |  11 +
 arch/arm/dts/vf.dtsi                       |  63 +++++
 arch/arm/dts/vf610-pcm052.dtsi             | 266 ++++++++++++++++++++
 arch/arm/dts/vf610-pinfunc.h               |  50 ++++
 arch/arm/include/asm/arch-vf610/clock.h    |   3 +
 arch/arm/include/asm/arch-vf610/imx-regs.h |   2 +
 board/phytec/pcm052/pcm052.c               | 386 +++++++----------------------
 configs/bk4r1_defconfig                    |  46 +++-
 configs/pcm052_defconfig                   |  32 ++-
 drivers/net/Kconfig                        |   2 +-
 drivers/net/fec_mxc.c                      |   1 +
 include/configs/bk4r1.h                    | 263 +++++++++++++++++++-
 include/configs/pcm052.h                   |  51 +---
 17 files changed, 925 insertions(+), 387 deletions(-)
 create mode 100644 arch/arm/dts/vf-u-boot.dtsi
 create mode 100644 arch/arm/dts/vf610-pcm052.dtsi

-- 
2.11.0