[U-Boot] [RFC 17/17] board: mx6sabresd: Remove non-DM code

Abel Vesa abel.vesa at nxp.com
Wed Jan 16 14:03:47 UTC 2019


Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabresd board file.

Signed-off-by: Abel Vesa <abel.vesa at nxp.com>
---
 board/freescale/mx6sabresd/mx6sabresd.c | 50 ---------------------------------
 1 file changed, 50 deletions(-)

diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index e3db2fd..71b9bfe 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -563,63 +563,13 @@ int board_eth_init(bd_t *bis)
 }
 
 #ifdef CONFIG_USB_EHCI_MX6
-#define USB_OTHERREGS_OFFSET	0x800
-#define UCTRL_PWR_POL		(1 << 9)
-
-static iomux_v3_cfg_t const usb_otg_pads[] = {
-	IOMUX_PADS(PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)),
-	IOMUX_PADS(PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static iomux_v3_cfg_t const usb_hc1_pads[] = {
-	IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
 static void setup_usb(void)
 {
-	SETUP_IOMUX_PADS(usb_otg_pads);
-
 	/*
 	 * set daisy chain for otg_pin_id on 6q.
 	 * for 6dl, this bit is reserved
 	 */
 	imx_iomux_set_gpr_register(1, 13, 1, 0);
-
-	SETUP_IOMUX_PADS(usb_hc1_pads);
-}
-
-int board_ehci_hcd_init(int port)
-{
-	u32 *usbnc_usb_ctrl;
-
-	if (port > 1)
-		return -EINVAL;
-
-	usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
-				 port * 4);
-
-	setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
-
-	return 0;
-}
-
-int board_ehci_power(int port, int on)
-{
-	switch (port) {
-	case 0:
-		break;
-	case 1:
-		if (on)
-			gpio_direction_output(IMX_GPIO_NR(1, 29), 1);
-		else
-			gpio_direction_output(IMX_GPIO_NR(1, 29), 0);
-		break;
-	default:
-		printf("MXC USB port %d not yet supported\n", port);
-		return -EINVAL;
-	}
-
-	return 0;
 }
 #endif
 
-- 
2.7.4



More information about the U-Boot mailing list