[U-Boot] [PATCH v2 17/22] board: mx6sabreauto: Remove the non-DM code

Peng Fan peng.fan at nxp.com
Tue Jan 29 13:43:49 UTC 2019



> -----Original Message-----
> From: Abel Vesa
> Sent: 2019年1月29日 19:35
> To: Tom Rini <trini at konsulko.com>; Fabio Estevam
> <fabio.estevam at nxp.com>; u-boot at lists.denx.de; dl-uboot-imx
> <uboot-imx at nxp.com>; Peng Fan <peng.fan at nxp.com>
> Cc: Nitin Garg <nitin.garg at nxp.com>; Abel Vesa <abel.vesa at nxp.com>
> Subject: [PATCH v2 17/22] board: mx6sabreauto: Remove the non-DM code
> 
> Since the mx6sabreauto has DM support, remove the unused non-DM code
> from mx6sabreauto board file.

Has DM_PCA953X been enabled?

Regards,
Peng.

> 
> Signed-off-by: Abel Vesa <abel.vesa at nxp.com>
> ---
>  board/freescale/mx6sabreauto/mx6sabreauto.c | 70
> -----------------------------
>  1 file changed, 70 deletions(-)
> 
> diff --git a/board/freescale/mx6sabreauto/mx6sabreauto.c
> b/board/freescale/mx6sabreauto/mx6sabreauto.c
> index c7e3e67..dd72de9 100644
> --- a/board/freescale/mx6sabreauto/mx6sabreauto.c
> +++ b/board/freescale/mx6sabreauto/mx6sabreauto.c
> @@ -159,44 +159,6 @@ static iomux_v3_cfg_t const port_exp[] = {
>  	IOMUX_PADS(PAD_SD2_DAT0__GPIO1_IO15	|
> MUX_PAD_CTRL(NO_PAD_CTRL)),
>  };
> 
> -/*Define for building port exp gpio, pin starts from 0*/ -#define
> PORTEXP_IO_NR(chip, pin) \
> -	((chip << 5) + pin)
> -
> -/*Get the chip addr from a ioexp gpio*/ -#define
> PORTEXP_IO_TO_CHIP(gpio_nr) \
> -	(gpio_nr >> 5)
> -
> -/*Get the pin number from a ioexp gpio*/ -#define
> PORTEXP_IO_TO_PIN(gpio_nr) \
> -	(gpio_nr & 0x1f)
> -
> -static int port_exp_direction_output(unsigned gpio, int value) -{
> -	int ret;
> -
> -	i2c_set_bus_num(2);
> -	ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio));
> -	if (ret)
> -		return ret;
> -
> -	ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio),
> -		(1 << PORTEXP_IO_TO_PIN(gpio)),
> -		(PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio)));
> -
> -	if (ret)
> -		return ret;
> -
> -	ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio),
> -		(1 << PORTEXP_IO_TO_PIN(gpio)),
> -		(value << PORTEXP_IO_TO_PIN(gpio)));
> -
> -	if (ret)
> -		return ret;
> -
> -	return 0;
> -}
> -
>  #ifdef CONFIG_MTD_NOR_FLASH
>  static iomux_v3_cfg_t const eimnor_pads[] = {
>  	IOMUX_PADS(PAD_EIM_D16__EIM_DATA16	|
> MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
> @@ -681,19 +643,10 @@ int checkboard(void)  }
> 
>  #ifdef CONFIG_USB_EHCI_MX6
> -#define USB_HOST1_PWR     PORTEXP_IO_NR(0x32, 7)
> -#define USB_OTG_PWR       PORTEXP_IO_NR(0x34, 1)
> -
> -iomux_v3_cfg_t const usb_otg_pads[] = {
> -	IOMUX_PADS(PAD_ENET_RX_ER__USB_OTG_ID |
> MUX_PAD_CTRL(NO_PAD_CTRL)),
> -};
> -
>  int board_ehci_hcd_init(int port)
>  {
>  	switch (port) {
>  	case 0:
> -		SETUP_IOMUX_PADS(usb_otg_pads);
> -
>  		/*
>  		  * Set daisy chain for otg_pin_id on 6q.
>  		 *  For 6dl, this bit is reserved.
> @@ -708,29 +661,6 @@ int board_ehci_hcd_init(int port)
>  	}
>  	return 0;
>  }
> -
> -int board_ehci_power(int port, int on)
> -{
> -	switch (port) {
> -	case 0:
> -		if (on)
> -			port_exp_direction_output(USB_OTG_PWR, 1);
> -		else
> -			port_exp_direction_output(USB_OTG_PWR, 0);
> -		break;
> -	case 1:
> -		if (on)
> -			port_exp_direction_output(USB_HOST1_PWR, 1);
> -		else
> -			port_exp_direction_output(USB_HOST1_PWR, 0);
> -		break;
> -	default:
> -		printf("MXC USB port %d not yet supported\n", port);
> -		return -EINVAL;
> -	}
> -
> -	return 0;
> -}
>  #endif
> 
>  #ifdef CONFIG_SPL_BUILD
> --
> 2.7.4



More information about the U-Boot mailing list