[U-Boot] [PATCH v2 7/8] net: Add MSCC Luton networkd driver.

Daniel Schwierzeck daniel.schwierzeck at gmail.com
Wed Jan 30 16:22:03 UTC 2019



Am 30.01.19 um 13:29 schrieb Horatiu Vultur:
> Add network driver for Microsemi Ethernet switch, it is
> present on Luton SoCs.

the series looks good so far, only some nits below

> 
> Signed-off-by: Horatiu Vultur <horatiu.vultur at microchip.com>
> ---
>  drivers/net/Kconfig                     |   7 +
>  drivers/net/Makefile                    |   2 +-
>  drivers/net/mscc_eswitch/Makefile       |   1 +
>  drivers/net/mscc_eswitch/luton_switch.c | 736 ++++++++++++++++++++++++++++++++
>  4 files changed, 745 insertions(+), 1 deletion(-)
>  create mode 100644 drivers/net/mscc_eswitch/luton_switch.c
> 
> diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
> index 39ce4e8..d82037d 100644
> --- a/drivers/net/Kconfig
> +++ b/drivers/net/Kconfig
> @@ -439,6 +439,13 @@ config MSCC_OCELOT_SWITCH
>  	help
>  	  This driver supports the Ocelot network switch device.
>  
> +config MSCC_LUTON_SWITCH
> +	bool "Luton switch driver"
> +	depends on DM_ETH && ARCH_MSCC
> +	select PHYLIB
> +	help
> +	  This driver supports the Luton network switch device.
> +

maybe it makes sense to move the MSCC_*_SWITCH options to
driver/net/mscc_eswitch/Kconfig especially when you want to support more
SoCs in the future

>  config ETHER_ON_FEC1
>  	bool "FEC1"
>  	depends on MPC8XX_FEC
> diff --git a/drivers/net/Makefile b/drivers/net/Makefile
> index 3ab7f26..51be72b 100644
> --- a/drivers/net/Makefile
> +++ b/drivers/net/Makefile
> @@ -75,4 +75,4 @@ obj-$(CONFIG_FSL_PFE) += pfe_eth/
>  obj-$(CONFIG_SNI_AVE) += sni_ave.o
>  obj-y += ti/
>  obj-$(CONFIG_MEDIATEK_ETH) += mtk_eth.o
> -obj-$(CONFIG_MSCC_OCELOT_SWITCH) += mscc_eswitch/
> +obj-y += mscc_eswitch/

this change would fit better to patch 1/8

> diff --git a/drivers/net/mscc_eswitch/Makefile b/drivers/net/mscc_eswitch/Makefile
> index 704f854..751a839 100644
> --- a/drivers/net/mscc_eswitch/Makefile
> +++ b/drivers/net/mscc_eswitch/Makefile
> @@ -1,2 +1,3 @@
>  
>  obj-$(CONFIG_MSCC_OCELOT_SWITCH) += ocelot_switch.o mscc_miim.o mscc_xfer.o mscc_mac_table.o
> +obj-$(CONFIG_MSCC_LUTON_SWITCH) += luton_switch.o mscc_miim.o mscc_xfer.o mscc_mac_table.o
> diff --git a/drivers/net/mscc_eswitch/luton_switch.c b/drivers/net/mscc_eswitch/luton_switch.c
> new file mode 100644
> index 0000000..dee6f15
> --- /dev/null
> +++ b/drivers/net/mscc_eswitch/luton_switch.c
> @@ -0,0 +1,736 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 Microsemi Corporation
> + */
> +
> +#include <common.h>
> +#include <config.h>
> +#include <dm.h>
> +#include <dm/of_access.h>
> +#include <dm/of_addr.h>
> +#include <fdt_support.h>
> +#include <linux/io.h>
> +#include <linux/ioport.h>
> +#include <miiphy.h>
> +#include <net.h>
> +#include <wait_bit.h>
> +
> +#include "mscc_miim.h"
> +#include "mscc_xfer.h"
> +#include "mscc_mac_table.h"
> +
> +#define ANA_PORT_VLAN_CFG(x)		(0x00 + 0x80 * (x))
> +#define		ANA_PORT_VLAN_CFG_AWARE_ENA	BIT(20)
> +#define		ANA_PORT_VLAN_CFG_POP_CNT(x)	((x) << 18)
> +#define ANA_PORT_CPU_FWD_CFG(x)		(0x50 + 0x80 * (x))
> +#define		ANA_PORT_CPU_FWD_CFG_SRC_COPY_ENA	BIT(1)
> +#define ANA_PORT_PORT_CFG(x)		(0x60 + 0x80 * (x))
> +#define		ANA_PORT_PORT_CFG_RECV_ENA	BIT(5)
> +#define ANA_PGID(x)			(0x1000 + 4 * (x))
> +
> +#define SYS_FRM_AGING			0x8300
> +
> +#define SYS_SYSTEM_RST_CFG		0x81b0
> +#define		SYS_SYSTEM_RST_MEM_INIT		BIT(0)
> +#define		SYS_SYSTEM_RST_MEM_ENA		BIT(1)
> +#define		SYS_SYSTEM_RST_CORE_ENA		BIT(2)
> +#define SYS_PORT_MODE(x)		(0x81bc + 0x4 * (x))
> +#define		SYS_PORT_MODE_INCL_INJ_HDR	BIT(0)
> +#define SYS_SWITCH_PORT_MODE(x)		(0x8294 + 0x4 * (x))
> +#define		SYS_SWITCH_PORT_MODE_PORT_ENA	BIT(3)
> +#define SYS_EGR_NO_SHARING		0x8378
> +#define SYS_SCH_CPU			0x85a0
> +
> +#define REW_PORT_CFG(x)			(0x8 + 0x80 * (x))
> +#define		REW_PORT_CFG_IFH_INSERT_ENA	BIT(7)
> +
> +#define GCB_DEVCPU_RST_SOFT_CHIP_RST	0x90
> +#define		GCB_DEVCPU_RST_SOFT_CHIP_RST_SOFT_PHY	BIT(1)
> +#define GCB_MISC_STAT			0x11c
> +#define		GCB_MISC_STAT_PHY_READY			BIT(3)
> +
> +#define	QS_XTR_MAP(x)			(0x10 + 4 * (x))
> +#define		QS_XTR_MAP_GRP			BIT(4)
> +#define		QS_XTR_MAP_ENA			BIT(0)
> +
> +#define HSIO_PLL5G_CFG_PLL5G_CFG2	0x8
> +
> +#define HSIO_RCOMP_CFG_CFG0		0x20
> +#define		HSIO_RCOMP_CFG_CFG0_MODE_SEL(x)			((x) << 8)
> +#define		HSIO_RCOMP_CFG_CFG0_RUN_CAL			BIT(12)
> +#define HSIO_RCOMP_STATUS		0x24
> +#define		HSIO_RCOMP_STATUS_BUSY				BIT(12)
> +#define		HSIO_RCOMP_STATUS_RCOMP_M			GENMASK(3, 0)
> +#define HSIO_SERDES6G_ANA_CFG_DES_CFG	0x64
> +#define		HSIO_SERDES6G_ANA_CFG_DES_CFG_BW_ANA(x)		((x) << 1)
> +#define		HSIO_SERDES6G_ANA_CFG_DES_CFG_BW_HYST(x)	((x) << 5)
> +#define		HSIO_SERDES6G_ANA_CFG_DES_CFG_MBTR_CTRL(x)	((x) << 10)
> +#define		HSIO_SERDES6G_ANA_CFG_DES_CFG_PHS_CTRL(x)	((x) << 13)
> +#define HSIO_SERDES6G_ANA_CFG_IB_CFG	0x68
> +#define		HSIO_SERDES6G_ANA_CFG_IB_CFG_RESISTOR_CTRL(x)	(x)
> +#define		HSIO_SERDES6G_ANA_CFG_IB_CFG_VBCOM(x)		((x) << 4)
> +#define		HSIO_SERDES6G_ANA_CFG_IB_CFG_VBAC(x)		((x) << 7)
> +#define		HSIO_SERDES6G_ANA_CFG_IB_CFG_RT(x)		((x) << 9)
> +#define		HSIO_SERDES6G_ANA_CFG_IB_CFG_RF(x)		((x) << 14)
> +#define HSIO_SERDES6G_ANA_CFG_IB_CFG1	0x6c
> +#define		HSIO_SERDES6G_ANA_CFG_IB_CFG1_RST		BIT(0)
> +#define		HSIO_SERDES6G_ANA_CFG_IB_CFG1_ENA_OFFSDC	BIT(2)
> +#define		HSIO_SERDES6G_ANA_CFG_IB_CFG1_ENA_OFFSAC	BIT(3)
> +#define		HSIO_SERDES6G_ANA_CFG_IB_CFG1_ANEG_MODE	BIT(6)
> +#define		HSIO_SERDES6G_ANA_CFG_IB_CFG1_CHF		BIT(7)
> +#define		HSIO_SERDES6G_ANA_CFG_IB_CFG1_C(x)		((x) << 8)
> +#define HSIO_SERDES6G_ANA_CFG_OB_CFG	0x70
> +#define		HSIO_SERDES6G_ANA_CFG_OB_CFG_SR(x)		((x) << 4)
> +#define		HSIO_SERDES6G_ANA_CFG_OB_CFG_SR_H		BIT(8)
> +#define		HSIO_SERDES6G_ANA_CFG_OB_CFG_POST0(x)		((x) << 23)
> +#define		HSIO_SERDES6G_ANA_CFG_OB_CFG_POL		BIT(29)
> +#define		HSIO_SERDES6G_ANA_CFG_OB_CFG_ENA1V_MODE	BIT(30)
> +#define HSIO_SERDES6G_ANA_CFG_OB_CFG1	0x74
> +#define		HSIO_SERDES6G_ANA_CFG_OB_CFG1_LEV(x)		(x)
> +#define		HSIO_SERDES6G_ANA_CFG_OB_CFG1_ENA_CAS(x)	((x) << 6)
> +#define HSIO_SERDES6G_ANA_CFG_COMMON_CFG 0x7c
> +#define		HSIO_SERDES6G_ANA_CFG_COMMON_CFG_IF_MODE(x)	(x)
> +#define		HSIO_SERDES6G_ANA_CFG_COMMON_CFG_ENA_LANE	BIT(18)
> +#define		HSIO_SERDES6G_ANA_CFG_COMMON_CFG_SYS_RST	BIT(31)
> +#define HSIO_SERDES6G_ANA_CFG_PLL_CFG	0x80
> +#define		HSIO_SERDES6G_ANA_CFG_PLL_CFG_FSM_ENA		BIT(7)
> +#define		HSIO_SERDES6G_ANA_CFG_PLL_CFG_FSM_CTRL_DATA(x)	((x) << 8)
> +#define HSIO_SERDES6G_ANA_CFG_SER_CFG	0x84
> +#define HSIO_SERDES6G_DIG_CFG_MISC_CFG	0x88
> +#define		HSIO_SERDES6G_DIG_CFG_MISC_CFG_LANE_RST		BIT(0)
> +#define HSIO_MCB_SERDES6G_CFG		0xac
> +#define		HSIO_MCB_SERDES6G_CFG_WR_ONE_SHOT		BIT(31)
> +#define		HSIO_MCB_SERDES6G_CFG_ADDR(x)			(x)
> +
> +#define DEV_GMII_PORT_MODE_CLK		0x0
> +#define		DEV_GMII_PORT_MODE_CLK_PHY_RST	BIT(0)
> +#define DEV_GMII_MAC_CFG_MAC_ENA	0xc
> +#define		DEV_GMII_MAC_CFG_MAC_ENA_RX_ENA		BIT(4)
> +#define		DEV_GMII_MAC_CFG_MAC_ENA_TX_ENA		BIT(0)
> +
> +#define DEV_PORT_MODE_CLK		0x4
> +#define		DEV_PORT_MODE_CLK_PHY_RST		BIT(2)
> +#define		DEV_PORT_MODE_CLK_LINK_SPEED_1000	1
> +#define DEV_MAC_CFG_MAC_ENA		0x10
> +#define		DEV_MAC_CFG_MAC_ENA_RX_ENA		BIT(4)
> +#define		DEV_MAC_CFG_MAC_ENA_TX_ENA		BIT(0)
> +#define DEV_MAC_CFG_MAC_IFG		0x24
> +#define		DEV_MAC_CFG_MAC_IFG_TX_IFG(x)		((x) << 8)
> +#define		DEV_MAC_CFG_MAC_IFG_RX_IFG2(x)		((x) << 4)
> +#define		DEV_MAC_CFG_MAC_IFG_RX_IFG1(x)		(x)
> +#define DEV_PCS1G_CFG_PCS1G_CFG		0x40
> +#define		DEV_PCS1G_CFG_PCS1G_CFG_PCS_ENA		BIT(0)
> +#define DEV_PCS1G_CFG_PCS1G_MODE	0x44
> +#define DEV_PCS1G_CFG_PCS1G_SD		0x48
> +#define DEV_PCS1G_CFG_PCS1G_ANEG	0x4c
> +#define		DEV_PCS1G_CFG_PCS1G_ANEG_ADV_ABILITY(x)	((x) << 16)
> +
> +#define IFH_INJ_BYPASS		BIT(31)
> +#define IFH_TAG_TYPE_C		0
> +#define MAC_VID			1
> +#define CPU_PORT		26
> +#define INTERNAL_PORT_MSK	0xFFFFFF
> +#define IFH_LEN			2
> +#define ETH_ALEN		6
> +#define PGID_BROADCAST		28
> +#define PGID_UNICAST		29
> +#define PGID_SRC		80
> +
> +enum luton_target {
> +	PORT0,
> +	PORT1,
> +	PORT2,
> +	PORT3,
> +	PORT4,
> +	PORT5,
> +	PORT6,
> +	PORT7,
> +	PORT8,
> +	PORT9,
> +	PORT10,
> +	PORT11,
> +	PORT12,
> +	PORT13,
> +	PORT14,
> +	PORT15,
> +	PORT16,
> +	PORT17,
> +	PORT18,
> +	PORT19,
> +	PORT20,
> +	PORT21,
> +	PORT22,
> +	PORT23,
> +	SYS,
> +	ANA,
> +	REW,
> +	GCB,
> +	QS,
> +	HSIO,
> +	TARGET_MAX,
> +};
> +
> +#define MAX_PORT (PORT23 - PORT0 + 1)
> +
> +#define MIN_INT_PORT PORT0
> +#define MAX_INT_PORT (PORT11 - PORT0  + 1)
> +#define MIN_EXT_PORT PORT12
> +#define MAX_EXT_PORT MAX_PORT
> +
> +enum luton_mdio_target {
> +	MIIM,
> +	TARGET_MDIO_MAX,
> +};
> +
> +enum luton_phy_id {
> +	INTERNAL,
> +	EXTERNAL,
> +	NUM_PHY,
> +};
> +
> +struct luton_private {
> +	void __iomem *regs[TARGET_MAX];
> +	struct mii_dev *bus[NUM_PHY];
> +};
> +
> +static const unsigned long luton_regs_qs[] = {
> +	[MSCC_QS_XTR_RD] = 0x18,
> +	[MSCC_QS_XTR_FLUSH] = 0x28,
> +	[MSCC_QS_XTR_DATA_PRESENT] = 0x2c,
> +	[MSCC_QS_INJ_WR] = 0x3c,
> +	[MSCC_QS_INJ_CTRL] = 0x44,
> +};
> +
> +static const unsigned long luton_regs_ana_table[] = {
> +	[MSCC_ANA_TABLES_MACHDATA] = 0x11b0,
> +	[MSCC_ANA_TABLES_MACLDATA] = 0x11b4,
> +	[MSCC_ANA_TABLES_MACACCESS] = 0x11b8,
> +};
> +
> +struct mscc_miim_dev miim[NUM_PHY];

I overlooked this in the previous patches but this should be either
static or a member of struct luton_private (and ocelot_private)

> +
> +static struct mii_dev *luton_mdiobus_init(struct udevice *dev,
> +					  int mdiobus_id)
> +{
> +	unsigned long phy_size[NUM_PHY];
> +	phys_addr_t phy_base[NUM_PHY];
> +	struct ofnode_phandle_args phandle;
> +	ofnode eth_node, node, mdio_node;
> +	struct resource res;
> +	struct mii_dev *bus;
> +	fdt32_t faddr;
> +	int i;
> +
> +	bus = mdio_alloc();
> +	if (!bus)
> +		return NULL;
> +
> +	/* gather only the first mdio bus */
> +	eth_node = dev_read_first_subnode(dev);
> +	node = ofnode_first_subnode(eth_node);
> +	ofnode_parse_phandle_with_args(node, "phy-handle", NULL, 0, 0,
> +				       &phandle);
> +	mdio_node = ofnode_get_parent(phandle.node);
> +
> +	for (i = 0; i < TARGET_MDIO_MAX; i++) {
> +		if (ofnode_read_resource(mdio_node, i, &res)) {
> +			pr_err("%s: get OF resource failed\n", __func__);
> +			return NULL;
> +		}
> +
> +		faddr = cpu_to_fdt32(res.start);
> +		phy_base[i] = ofnode_translate_address(mdio_node, &faddr);
> +		phy_size[i] = res.end - res.start;
> +	}
> +
> +	strcpy(bus->name, "miim-internal");
> +	miim[mdiobus_id].regs = ioremap(phy_base[mdiobus_id],
> +					phy_size[mdiobus_id]);
> +	bus->priv = &miim[mdiobus_id];
> +	bus->read = mscc_miim_read;
> +	bus->write = mscc_miim_write;
> +
> +	if (mdio_register(bus))
> +		return NULL;
> +	else
> +		return bus;
> +}
> +
> +static void luton_stop(struct udevice *dev)
> +{
> +	struct luton_private *priv = dev_get_priv(dev);
> +
> +	/*
> +	 * Switch core only reset affects VCORE-III bus and MIPS frequency
> +	 * and thereby also the DDR SDRAM controller. The workaround is to
> +	 * not to redirect any trafic to the CPU after the data transfer.
> +	 */
> +	writel(GENMASK(9, 2), priv->regs[SYS] + SYS_SCH_CPU);
> +}
> +
> +static void luton_cpu_capture_setup(struct luton_private *priv)
> +{
> +	int i;
> +
> +	/* map the 8 CPU extraction queues to CPU port 26 */
> +	writel(0x0, priv->regs[SYS] + SYS_SCH_CPU);
> +
> +	for (i = 0; i <= 1; i++) {
> +		/*
> +		 * One to one mapping from CPU Queue number to Group extraction
> +		 * number
> +		 */
> +		writel(QS_XTR_MAP_ENA | (QS_XTR_MAP_GRP * i),
> +		       priv->regs[QS] + QS_XTR_MAP(i));
> +
> +		/* Enable IFH insertion/parsing on CPU ports */
> +		setbits_le32(priv->regs[REW] + REW_PORT_CFG(CPU_PORT + i),
> +			     REW_PORT_CFG_IFH_INSERT_ENA);
> +
> +		/* Enable IFH parsing on CPU port 0 and 1 */
> +		setbits_le32(priv->regs[SYS] + SYS_PORT_MODE(CPU_PORT + i),
> +			     SYS_PORT_MODE_INCL_INJ_HDR);
> +	}
> +
> +	/* Make VLAN aware for CPU traffic */
> +	writel(ANA_PORT_VLAN_CFG_AWARE_ENA |
> +	       ANA_PORT_VLAN_CFG_POP_CNT(1) |
> +	       MAC_VID,
> +	       priv->regs[ANA] + ANA_PORT_VLAN_CFG(CPU_PORT));
> +
> +	/* Disable learning (only RECV_ENA must be set) */
> +	writel(ANA_PORT_PORT_CFG_RECV_ENA,
> +	       priv->regs[ANA] + ANA_PORT_PORT_CFG(CPU_PORT));
> +
> +	/* Enable switching to/from cpu port */
> +	setbits_le32(priv->regs[SYS] + SYS_SWITCH_PORT_MODE(CPU_PORT),
> +		     SYS_SWITCH_PORT_MODE_PORT_ENA);
> +
> +	setbits_le32(priv->regs[SYS] + SYS_EGR_NO_SHARING, BIT(CPU_PORT));
> +}
> +
> +static void luton_gmii_port_init(struct luton_private *priv, int port)
> +{
> +	void __iomem *regs = priv->regs[port];
> +
> +	writel(0, regs + DEV_GMII_PORT_MODE_CLK);
> +
> +	/* Enable MAC RX and TX */
> +	writel(DEV_GMII_MAC_CFG_MAC_ENA_RX_ENA |
> +	       DEV_GMII_MAC_CFG_MAC_ENA_TX_ENA,
> +	       regs + DEV_GMII_MAC_CFG_MAC_ENA);
> +
> +	/* Make VLAN aware for CPU traffic */
> +	writel(ANA_PORT_VLAN_CFG_AWARE_ENA |
> +	       ANA_PORT_VLAN_CFG_POP_CNT(1) |
> +	       MAC_VID,
> +	       priv->regs[ANA] + ANA_PORT_VLAN_CFG(port - PORT0));
> +
> +	/* Enable switching to/from port */
> +	setbits_le32(priv->regs[SYS] + SYS_SWITCH_PORT_MODE(port - PORT0),
> +		     SYS_SWITCH_PORT_MODE_PORT_ENA);
> +}
> +
> +static void luton_port_init(struct luton_private *priv, int port)
> +{
> +	void __iomem *regs = priv->regs[port];
> +
> +	writel(0, regs + DEV_PORT_MODE_CLK);
> +
> +	/* Enable MAC RX and TX */
> +	writel(DEV_MAC_CFG_MAC_ENA_RX_ENA |
> +	       DEV_MAC_CFG_MAC_ENA_TX_ENA,
> +	       regs + DEV_MAC_CFG_MAC_ENA);
> +
> +	/* Make VLAN aware for CPU traffic */
> +	writel(ANA_PORT_VLAN_CFG_AWARE_ENA |
> +	       ANA_PORT_VLAN_CFG_POP_CNT(1) |
> +	       MAC_VID,
> +	       priv->regs[ANA] + ANA_PORT_VLAN_CFG(port - PORT0));
> +
> +	/* Enable switching to/from port */
> +	setbits_le32(priv->regs[SYS] + SYS_SWITCH_PORT_MODE(port - PORT0),
> +		     SYS_SWITCH_PORT_MODE_PORT_ENA);
> +}
> +
> +static void luton_ext_port_init(struct luton_private *priv, int port)
> +{
> +	void __iomem *regs = priv->regs[port];
> +
> +	/* Enable PCS */
> +	writel(DEV_PCS1G_CFG_PCS1G_CFG_PCS_ENA,
> +	       regs + DEV_PCS1G_CFG_PCS1G_CFG);
> +
> +	/* Disable Signal Detect */
> +	writel(0, regs + DEV_PCS1G_CFG_PCS1G_SD);
> +
> +	/* Enable MAC RX and TX */
> +	writel(DEV_MAC_CFG_MAC_ENA_RX_ENA |
> +	       DEV_MAC_CFG_MAC_ENA_TX_ENA,
> +	       regs + DEV_MAC_CFG_MAC_ENA);
> +
> +	/* Clear sgmii_mode_ena */
> +	writel(0, regs + DEV_PCS1G_CFG_PCS1G_MODE);
> +
> +	/*
> +	 * Clear sw_resolve_ena(bit 0) and set adv_ability to
> +	 * something meaningful just in case
> +	 */
> +	writel(DEV_PCS1G_CFG_PCS1G_ANEG_ADV_ABILITY(0x20),
> +	       regs + DEV_PCS1G_CFG_PCS1G_ANEG);
> +
> +	/* Set MAC IFG Gaps */
> +	writel(DEV_MAC_CFG_MAC_IFG_TX_IFG(7) |
> +	       DEV_MAC_CFG_MAC_IFG_RX_IFG1(1) |
> +	       DEV_MAC_CFG_MAC_IFG_RX_IFG2(5),
> +	       regs + DEV_MAC_CFG_MAC_IFG);
> +
> +	/* Set link speed and release all resets */
> +	writel(DEV_PORT_MODE_CLK_LINK_SPEED_1000,
> +	       regs + DEV_PORT_MODE_CLK);
> +
> +	/* Make VLAN aware for CPU traffic */
> +	writel(ANA_PORT_VLAN_CFG_AWARE_ENA |
> +	       ANA_PORT_VLAN_CFG_POP_CNT(1) |
> +	       MAC_VID,
> +	       priv->regs[ANA] + ANA_PORT_VLAN_CFG(port - PORT0));
> +
> +	/* Enable switching to/from port */
> +	setbits_le32(priv->regs[SYS] + SYS_SWITCH_PORT_MODE(port - PORT0),
> +		     SYS_SWITCH_PORT_MODE_PORT_ENA);
> +}
> +
> +static void serdes6g_write(struct luton_private *priv, u32 addr)
> +{
> +	u32 data;
> +
> +	writel(HSIO_MCB_SERDES6G_CFG_WR_ONE_SHOT |
> +	       HSIO_MCB_SERDES6G_CFG_ADDR(addr),
> +	       priv->regs[HSIO] + HSIO_MCB_SERDES6G_CFG);
> +
> +	do {
> +		data = readl(priv->regs[HSIO] + HSIO_MCB_SERDES6G_CFG);
> +	} while (data & HSIO_MCB_SERDES6G_CFG_WR_ONE_SHOT);
> +
> +	mdelay(100);
> +}
> +
> +static void serdes6g_cfg(struct luton_private *priv)
> +{
> +	writel(HSIO_RCOMP_CFG_CFG0_MODE_SEL(0x3) |
> +	       HSIO_RCOMP_CFG_CFG0_RUN_CAL,
> +	       priv->regs[HSIO] + HSIO_RCOMP_CFG_CFG0);
> +
> +	while (readl(priv->regs[HSIO] + HSIO_RCOMP_STATUS) &
> +	       HSIO_RCOMP_STATUS_BUSY)
> +		;
> +
> +	writel(HSIO_SERDES6G_ANA_CFG_OB_CFG_SR(0xb) |
> +	       HSIO_SERDES6G_ANA_CFG_OB_CFG_SR_H |
> +	       HSIO_SERDES6G_ANA_CFG_OB_CFG_POST0(0x10) |
> +	       HSIO_SERDES6G_ANA_CFG_OB_CFG_POL |
> +	       HSIO_SERDES6G_ANA_CFG_OB_CFG_ENA1V_MODE,
> +	       priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_OB_CFG);
> +	writel(HSIO_SERDES6G_ANA_CFG_OB_CFG1_LEV(0x18) |
> +	       HSIO_SERDES6G_ANA_CFG_OB_CFG1_ENA_CAS(0x1),
> +	       priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_OB_CFG1);
> +	writel(HSIO_SERDES6G_ANA_CFG_IB_CFG_RESISTOR_CTRL(0xc) |
> +	       HSIO_SERDES6G_ANA_CFG_IB_CFG_VBCOM(0x4) |
> +	       HSIO_SERDES6G_ANA_CFG_IB_CFG_VBAC(0x5) |
> +	       HSIO_SERDES6G_ANA_CFG_IB_CFG_RT(0xf) |
> +	       HSIO_SERDES6G_ANA_CFG_IB_CFG_RF(0x4),
> +	       priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_IB_CFG);
> +	writel(HSIO_SERDES6G_ANA_CFG_IB_CFG1_RST |
> +	       HSIO_SERDES6G_ANA_CFG_IB_CFG1_ENA_OFFSDC |
> +	       HSIO_SERDES6G_ANA_CFG_IB_CFG1_ENA_OFFSAC |
> +	       HSIO_SERDES6G_ANA_CFG_IB_CFG1_ANEG_MODE |
> +	       HSIO_SERDES6G_ANA_CFG_IB_CFG1_CHF |
> +	       HSIO_SERDES6G_ANA_CFG_IB_CFG1_C(0x4),
> +	       priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_IB_CFG1);
> +	writel(HSIO_SERDES6G_ANA_CFG_DES_CFG_BW_ANA(0x5) |
> +	       HSIO_SERDES6G_ANA_CFG_DES_CFG_BW_HYST(0x5) |
> +	       HSIO_SERDES6G_ANA_CFG_DES_CFG_MBTR_CTRL(0x2) |
> +	       HSIO_SERDES6G_ANA_CFG_DES_CFG_PHS_CTRL(0x6),
> +	       priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_DES_CFG);
> +	writel(HSIO_SERDES6G_ANA_CFG_PLL_CFG_FSM_ENA |
> +	       HSIO_SERDES6G_ANA_CFG_PLL_CFG_FSM_CTRL_DATA(0x78),
> +	       priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_PLL_CFG);
> +	writel(HSIO_SERDES6G_ANA_CFG_COMMON_CFG_IF_MODE(0x30) |
> +	       HSIO_SERDES6G_ANA_CFG_COMMON_CFG_ENA_LANE,
> +	       priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_COMMON_CFG);
> +	/*
> +	 * There are 4 serdes6g, configure all except serdes6g0, therefore
> +	 * the address is b1110
> +	 */
> +	serdes6g_write(priv, 0xe);
> +
> +	writel(readl(priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_COMMON_CFG) |
> +	       HSIO_SERDES6G_ANA_CFG_COMMON_CFG_SYS_RST,
> +	       priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_COMMON_CFG);
> +	serdes6g_write(priv, 0xe);
> +
> +	clrbits_le32(priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_IB_CFG1,
> +		     HSIO_SERDES6G_ANA_CFG_IB_CFG1_RST);
> +	writel(HSIO_SERDES6G_DIG_CFG_MISC_CFG_LANE_RST,
> +	       priv->regs[HSIO] + HSIO_SERDES6G_DIG_CFG_MISC_CFG);
> +	serdes6g_write(priv, 0xe);
> +}
> +
> +static int luton_switch_init(struct luton_private *priv)
> +{
> +	setbits_le32(priv->regs[HSIO] + HSIO_PLL5G_CFG_PLL5G_CFG2, BIT(1));
> +	clrbits_le32(priv->regs[HSIO] + HSIO_PLL5G_CFG_PLL5G_CFG2, BIT(1));
> +
> +	/* Reset switch & memories */
> +	writel(SYS_SYSTEM_RST_MEM_ENA | SYS_SYSTEM_RST_MEM_INIT,
> +	       priv->regs[SYS] + SYS_SYSTEM_RST_CFG);
> +
> +	/* Wait to complete */
> +	if (wait_for_bit_le32(priv->regs[SYS] + SYS_SYSTEM_RST_CFG,
> +			      SYS_SYSTEM_RST_MEM_INIT, false, 2000, false)) {
> +		printf("Timeout in memory reset\n");
> +	}
> +
> +	/* Enable switch core */
> +	setbits_le32(priv->regs[SYS] + SYS_SYSTEM_RST_CFG,
> +		     SYS_SYSTEM_RST_CORE_ENA);
> +
> +	/* Setup the Serdes6g macros */
> +	serdes6g_cfg(priv);
> +
> +	return 0;
> +}
> +
> +static int luton_initialize(struct luton_private *priv)
> +{
> +	int ret, i;
> +
> +	/* Initialize switch memories, enable core */
> +	ret = luton_switch_init(priv);
> +	if (ret)
> +		return ret;
> +
> +	/*
> +	 * Disable port-to-port by switching
> +	 * Put front ports in "port isolation modes" - i.e. they can't send
> +	 * to other ports - via the PGID sorce masks.
> +	 */
> +	for (i = 0; i < MAX_PORT; i++)
> +		writel(0, priv->regs[ANA] + ANA_PGID(PGID_SRC + i));
> +
> +	/* Flush queues */
> +	mscc_flush(priv->regs[QS], luton_regs_qs);
> +
> +	/* Setup frame ageing - "2 sec" - The unit is 4ns on Luton*/
> +	writel(2000000000 / 4,
> +	       priv->regs[SYS] + SYS_FRM_AGING);
> +
> +	for (i = PORT0; i < MAX_PORT; i++) {
> +		if (i < PORT10)
> +			luton_gmii_port_init(priv, i);
> +		else
> +			if (i == PORT10 || i == PORT11)
> +				luton_port_init(priv, i);
> +			else
> +				luton_ext_port_init(priv, i);
> +	}
> +
> +	luton_cpu_capture_setup(priv);
> +
> +	return 0;
> +}
> +
> +static int luton_write_hwaddr(struct udevice *dev)
> +{
> +	struct luton_private *priv = dev_get_priv(dev);
> +	struct eth_pdata *pdata = dev_get_platdata(dev);
> +
> +	mscc_mac_table_add(priv->regs[ANA], luton_regs_ana_table,
> +			   pdata->enetaddr, PGID_UNICAST);
> +
> +	writel(BIT(CPU_PORT), priv->regs[ANA] + ANA_PGID(PGID_UNICAST));
> +
> +	return 0;
> +}
> +
> +static int luton_start(struct udevice *dev)
> +{
> +	struct luton_private *priv = dev_get_priv(dev);
> +	struct eth_pdata *pdata = dev_get_platdata(dev);
> +	const unsigned char mac[ETH_ALEN] = { 0xff, 0xff, 0xff, 0xff, 0xff,
> +					      0xff };
> +	int ret;
> +
> +	ret = luton_initialize(priv);
> +	if (ret)
> +		return ret;
> +
> +	/* Set MAC address tables entries for CPU redirection */
> +	mscc_mac_table_add(priv->regs[ANA], luton_regs_ana_table,
> +			   mac, PGID_BROADCAST);
> +
> +	writel(BIT(CPU_PORT) | INTERNAL_PORT_MSK,
> +	       priv->regs[ANA] + ANA_PGID(PGID_BROADCAST));
> +
> +	mscc_mac_table_add(priv->regs[ANA], luton_regs_ana_table,
> +			   pdata->enetaddr, PGID_UNICAST);
> +
> +	writel(BIT(CPU_PORT), priv->regs[ANA] + ANA_PGID(PGID_UNICAST));
> +
> +	return 0;
> +}
> +
> +static int luton_send(struct udevice *dev, void *packet, int length)
> +{
> +	struct luton_private *priv = dev_get_priv(dev);
> +	u32 ifh[IFH_LEN];
> +	int port = BIT(0);	/* use port 0 */
> +	u32 *buf = packet;
> +
> +	ifh[0] = IFH_INJ_BYPASS | port;
> +	ifh[1] = (IFH_TAG_TYPE_C << 16);
> +
> +	return mscc_send(priv->regs[QS], luton_regs_qs,
> +			 ifh, IFH_LEN, buf, length);
> +}
> +
> +static int luton_recv(struct udevice *dev, int flags, uchar **packetp)
> +{
> +	struct luton_private *priv = dev_get_priv(dev);
> +	u32 *rxbuf = (u32 *)net_rx_packets[0];
> +	int byte_cnt = 0;
> +
> +	byte_cnt = mscc_recv(priv->regs[QS], luton_regs_qs, rxbuf, IFH_LEN,
> +			     true);
> +
> +	*packetp = net_rx_packets[0];
> +
> +	return byte_cnt;
> +}
> +
> +static int luton_probe(struct udevice *dev)
> +{
> +	struct luton_private *priv = dev_get_priv(dev);
> +	int i;
> +
> +	struct {
> +		enum luton_target id;
> +		char *name;
> +	} reg[] = {
> +		{ PORT0, "port0" },
> +		{ PORT1, "port1" },
> +		{ PORT2, "port2" },
> +		{ PORT3, "port3" },
> +		{ PORT4, "port4" },
> +		{ PORT5, "port5" },
> +		{ PORT6, "port6" },
> +		{ PORT7, "port7" },
> +		{ PORT8, "port8" },
> +		{ PORT9, "port9" },
> +		{ PORT10, "port10" },
> +		{ PORT11, "port11" },
> +		{ PORT12, "port12" },
> +		{ PORT13, "port13" },
> +		{ PORT14, "port14" },
> +		{ PORT15, "port15" },
> +		{ PORT16, "port16" },
> +		{ PORT17, "port17" },
> +		{ PORT18, "port18" },
> +		{ PORT19, "port19" },
> +		{ PORT20, "port20" },
> +		{ PORT21, "port21" },
> +		{ PORT22, "port22" },
> +		{ PORT23, "port23" },
> +		{ SYS, "sys" },
> +		{ ANA, "ana" },
> +		{ REW, "rew" },
> +		{ GCB, "gcb" },
> +		{ QS, "qs" },
> +		{ HSIO, "hsio" },
> +	};
> +
> +	if (!priv)
> +		return -EINVAL;
> +
> +	for (i = 0; i < ARRAY_SIZE(reg); i++) {
> +		priv->regs[reg[i].id] = dev_remap_addr_name(dev, reg[i].name);
> +		if (!priv->regs[reg[i].id]) {
> +			debug
> +			    ("Error can't get regs base addresses for %s\n",
> +			     reg[i].name);
> +			return -ENOMEM;
> +		}
> +	}
> +
> +	/* Release reset in the CU-PHY */
> +	writel(0, priv->regs[GCB] + GCB_DEVCPU_RST_SOFT_CHIP_RST);
> +
> +	/* Ports with ext phy don't need to reset clk */
> +	for (i = PORT0; i < MAX_INT_PORT; i++) {
> +		if (i < PORT10)
> +			clrbits_le32(priv->regs[i] + DEV_GMII_PORT_MODE_CLK,
> +				     DEV_GMII_PORT_MODE_CLK_PHY_RST);
> +		else
> +			clrbits_le32(priv->regs[i] + DEV_PORT_MODE_CLK,
> +				     DEV_PORT_MODE_CLK_PHY_RST);
> +	}
> +
> +	/* Wait for internal PHY to be ready */
> +	if (wait_for_bit_le32(priv->regs[GCB] + GCB_MISC_STAT,
> +			      GCB_MISC_STAT_PHY_READY, true, 500, false))
> +		return -EACCES;
> +
> +	priv->bus[INTERNAL] = luton_mdiobus_init(dev, INTERNAL);
> +
> +	for (i = 0; i < MAX_INT_PORT; i++) {
> +		phy_connect(priv->bus[INTERNAL], i, dev,
> +			    PHY_INTERFACE_MODE_NONE);
> +	}
> +
> +	/*
> +	 * coma_mode is need on only one phy, because all the other phys
> +	 * will be affected.
> +	 */
> +	mscc_miim_write(priv->bus[INTERNAL], 0, 0, 31, 0x10);
> +	mscc_miim_write(priv->bus[INTERNAL], 0, 0, 14, 0x800);
> +	mscc_miim_write(priv->bus[INTERNAL], 0, 0, 31, 0);
> +
> +	return 0;
> +}
> +
> +static int luton_remove(struct udevice *dev)
> +{
> +	struct luton_private *priv = dev_get_priv(dev);
> +	int i;
> +
> +	for (i = 0; i < NUM_PHY; i++) {
> +		mdio_unregister(priv->bus[i]);
> +		mdio_free(priv->bus[i]);
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct eth_ops luton_ops = {
> +	.start        = luton_start,
> +	.stop         = luton_stop,
> +	.send         = luton_send,
> +	.recv         = luton_recv,
> +	.write_hwaddr = luton_write_hwaddr,
> +};
> +
> +static const struct udevice_id mscc_luton_ids[] = {
> +	{.compatible = "mscc,vsc7527-switch", },
> +	{ /* Sentinel */ }
> +};
> +
> +U_BOOT_DRIVER(luton) = {
> +	.name     = "luton-switch",
> +	.id       = UCLASS_ETH,
> +	.of_match = mscc_luton_ids,
> +	.probe	  = luton_probe,
> +	.remove	  = luton_remove,
> +	.ops	  = &luton_ops,
> +	.priv_auto_alloc_size = sizeof(struct luton_private),
> +	.platdata_auto_alloc_size = sizeof(struct eth_pdata),
> +};
> 

-- 
- Daniel


More information about the U-Boot mailing list