[U-Boot] [PATCH] board/BuR/brppt1: drop DM_I2C_COMPAT

[Hannes Schmelzer]

The TPS62517 PMIC driver has been partially converted to DM, so the
legacy I2C access layer isn't needed anymore.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer at br-automation.com>

---

 board/BuR/brppt1/board.c      | 5 ++---
 board/BuR/brxre1/board.c      | 2 +-
 board/BuR/common/bur_common.h | 2 +-
 board/BuR/common/common.c     | 7 ++++---
 configs/brppt1_mmc_defconfig  | 1 -
 configs/brppt1_nand_defconfig | 1 -
 configs/brppt1_spi_defconfig  | 1 -
 7 files changed, 8 insertions(+), 11 deletions(-)

diff --git a/board/BuR/brppt1/board.c b/board/BuR/brppt1/board.c
index d2e7c72..b8ab19c 100644
--- a/board/BuR/brppt1/board.c
+++ b/board/BuR/brppt1/board.c
@@ -106,9 +106,8 @@ void am33xx_spl_board_init(void)
 
 	/* setup I2C */
 	enable_i2c_pin_mux();
-	i2c_set_bus_num(0);
-	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
-	pmicsetup(0);
+
+	pmicsetup(0, 0);
 
 	/* peripheral reset */
 	rc = gpio_request(64 + 29, "GPMC_WAIT1");
diff --git a/board/BuR/brxre1/board.c b/board/BuR/brxre1/board.c
index 41ed28b..82c53d5 100644
--- a/board/BuR/brxre1/board.c
+++ b/board/BuR/brxre1/board.c
@@ -132,7 +132,7 @@ void am33xx_spl_board_init(void)
 		puts("ERROR: i2c_set_bus_speed failed! (turn on PWR_nEN)\n");
 	}
 
-	pmicsetup(0);
+	pmicsetup(0, 0);
 }
 
 const struct dpll_params *get_dpll_ddr_params(void)
diff --git a/board/BuR/common/bur_common.h b/board/BuR/common/bur_common.h
index 5f2d0d0..f743194 100644
--- a/board/BuR/common/bur_common.h
+++ b/board/BuR/common/bur_common.h
@@ -15,7 +15,7 @@
 
 int load_lcdtiming(struct am335x_lcdpanel *panel);
 void br_summaryscreen(void);
-void pmicsetup(u32 mpupll);
+void pmicsetup(u32 mpupll, unsigned int bus);
 void enable_uart0_pin_mux(void);
 void enable_i2c_pin_mux(void);
 void enable_board_pin_mux(void);
diff --git a/board/BuR/common/common.c b/board/BuR/common/common.c
index f3eae5c..a1f7c44 100644
--- a/board/BuR/common/common.c
+++ b/board/BuR/common/common.c
@@ -269,13 +269,14 @@ int ft_board_setup(void *blob, bd_t *bd)
 
 static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
 
-void pmicsetup(u32 mpupll)
+void pmicsetup(u32 mpupll, unsigned int bus)
 {
 	int mpu_vdd;
 	int usb_cur_lim;
 
-	if (i2c_probe(TPS65217_CHIP_PM)) {
-		puts("PMIC (0x24) not found! skip further initalization.\n");
+	if (power_tps65217_init(bus)) {
+		printf("WARN: cannot setup PMIC 0x24 @ bus #%d, not found!.\n",
+		       bus);
 		return;
 	}
 
diff --git a/configs/brppt1_mmc_defconfig b/configs/brppt1_mmc_defconfig
index 083b5f7..f2d8220 100644
--- a/configs/brppt1_mmc_defconfig
+++ b/configs/brppt1_mmc_defconfig
@@ -71,7 +71,6 @@ CONFIG_SPL_DM_SEQ_ALIAS=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_DM_GPIO=y
 CONFIG_DM_I2C=y
-CONFIG_DM_I2C_COMPAT=y
 CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
 CONFIG_MISC=y
 CONFIG_DM_MMC=y
diff --git a/configs/brppt1_nand_defconfig b/configs/brppt1_nand_defconfig
index 1cfd5fc..275727d 100644
--- a/configs/brppt1_nand_defconfig
+++ b/configs/brppt1_nand_defconfig
@@ -73,7 +73,6 @@ CONFIG_BLK=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_DM_GPIO=y
 CONFIG_DM_I2C=y
-CONFIG_DM_I2C_COMPAT=y
 CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
 CONFIG_MISC=y
 # CONFIG_MMC is not set
diff --git a/configs/brppt1_spi_defconfig b/configs/brppt1_spi_defconfig
index 3737396..668c4c2 100644
--- a/configs/brppt1_spi_defconfig
+++ b/configs/brppt1_spi_defconfig
@@ -76,7 +76,6 @@ CONFIG_SPL_DM_SEQ_ALIAS=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_DM_GPIO=y
 CONFIG_DM_I2C=y
-CONFIG_DM_I2C_COMPAT=y
 CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
 CONFIG_MISC=y
 CONFIG_DM_MMC=y
-- 
2.7.4