[U-Boot] [EXT] Re: [PATCH 5/5] net: fec_mxc: Update driver to use full clks for iMX8
Ye Li
ye.li at nxp.com
Wed Jul 10 05:45:43 UTC 2019
在 2019/7/7 7:10, Lukasz Majewski 写道:
> Hi Ye,
>
>> Add support for more clocks used by iMX8 from DTB:
>> ref_clock, tx_2x_clock, ahb_clock
>> And update get clock rate interface to support multiple fec ports.
>>
>> Signed-off-by: Ye Li <ye.li at nxp.com>
>> ---
>> drivers/net/fec_mxc.c | 47
>> ++++++++++++++++++++++++++++++++++++++--------- drivers/net/fec_mxc.h
>> | 1 + 2 files changed, 39 insertions(+), 9 deletions(-)
>>
>> diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
>> index d7c0809..6d485f1 100644
>> --- a/drivers/net/fec_mxc.c
>> +++ b/drivers/net/fec_mxc.c
>> @@ -6,7 +6,6 @@
>> * (C) Copyright 2007 Pengutronix, Sascha Hauer
>> <s.hauer at pengutronix.de>
>> * (C) Copyright 2007 Pengutronix, Juergen Beisert
>> <j.beisert at pengutronix.de> */
>> -
>> #include <common.h>
>> #include <dm.h>
>> #include <environment.h>
>> @@ -132,9 +131,9 @@ static int fec_get_clk_rate(void *udev, int idx)
>>
>> dev = udev;
>> if (!dev) {
>> - ret = uclass_get_device(UCLASS_ETH, idx, &dev);
>> + ret = uclass_get_device_by_seq(UCLASS_ETH, idx,
>> &dev); if (ret < 0) {
>> - debug("Can't get FEC udev: %d\n", ret);
>> + debug("Can't get FEC udev%d: %d\n", idx,
>> ret); return ret;
>> }
>> }
>> @@ -149,7 +148,7 @@ static int fec_get_clk_rate(void *udev, int idx)
>> #endif
>> }
>>
>> -static void fec_mii_setspeed(struct ethernet_regs *eth)
>> +static void fec_mii_setspeed(struct ethernet_regs *eth, int idx)
>> {
>> /*
>> * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
>> @@ -171,7 +170,7 @@ static void fec_mii_setspeed(struct ethernet_regs
>> *eth) u32 hold;
>> int ret;
>>
>> - ret = fec_get_clk_rate(NULL, 0);
>> + ret = fec_get_clk_rate(NULL, idx);
>> if (ret < 0) {
>> printf("Can't find FEC0 clk rate: %d\n", ret);
>> return;
>> @@ -593,7 +592,7 @@ static int fec_init(struct eth_device *dev, bd_t
>> *bd) fec_reg_setup(fec);
>>
>> if (fec->xcv_type != SEVENWIRE)
>> - fec_mii_setspeed(fec->bus->priv);
>> + fec_mii_setspeed(fec->bus->priv, fec->dev_id);
>>
>> /* Set Opcode/Pause Duration Register */
>> writel(0x00010020, &fec->eth->op_pause); /* FIXME
>> 0xffff0020; */ @@ -1073,7 +1072,7 @@ struct mii_dev
>> *fec_get_miibus(ulong base_addr, int dev_id) free(bus);
>> return NULL;
>> }
>> - fec_mii_setspeed(eth);
>> + fec_mii_setspeed(eth, dev_id);
>> return bus;
>> }
>>
>> @@ -1142,7 +1141,7 @@ static int fec_probe(bd_t *bd, int dev_id,
>> uint32_t base_addr, fec_set_dev_name(edev->name, dev_id);
>> fec->dev_id = (dev_id == -1) ? 0 : dev_id;
>> fec->bus = bus;
>> - fec_mii_setspeed(bus->priv);
>> + fec_mii_setspeed(bus->priv, fec->dev_id);
>> #ifdef CONFIG_PHYLIB
>> fec->phydev = phydev;
>> phy_connect_dev(phydev, edev);
>> @@ -1324,6 +1323,7 @@ static int fecmxc_probe(struct udevice *dev)
>> int ret;
>>
>> if (IS_ENABLED(CONFIG_IMX8)) {
>> + struct clk ref_clk, clk_2x_txclk;
>> ret = clk_get_by_name(dev, "ipg", &priv->ipg_clk);
>> if (ret < 0) {
>> debug("Can't get FEC ipg clk: %d\n", ret);
>> @@ -1335,6 +1335,35 @@ static int fecmxc_probe(struct udevice *dev)
>> return ret;
>> }
>>
>> + ret = clk_get_by_name(dev, "ahb", &priv->ahb_clk);
>> + if (ret < 0) {
>> + debug("Can't get FEC ahb clk: %d\n", ret);
>> + return ret;
>> + }
>> + ret = clk_enable(&priv->ahb_clk);
>> + if (ret < 0) {
>> + debug("Can't enable FEC ahb clk: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + ret = clk_get_by_name(dev, "enet_clk_ref", &ref_clk);
>
> The enet clock is not only IMX8 specific.
Yes. But so far only IMX8 enables the clk-uclass. Others still use old way.
You can see IS_ENABLED(CONFIG_IMX8) is checked above the codes.
>
>> + if (ret >= 0) {
>> + ret = clk_enable(&ref_clk);
>> + if (ret < 0) {
>> + debug("Can't enable FEC ref clk:
>> %d\n", ret);
>> + return ret;
>> + }
>> + }
>> +
>> + ret = clk_get_by_name(dev, "enet_2x_txclk",
>> &clk_2x_txclk);
>> + if (ret >= 0) {
>> + ret = clk_enable(&clk_2x_txclk);
>> + if (ret < 0) {
>> + debug("Can't enable FEC 2x_tx clk:
>> %d\n", ret);
>> + return ret;
>> + }
>> + }
>> +
>> priv->clk_rate = clk_get_rate(&priv->ipg_clk);
>> }
>>
>> @@ -1368,7 +1397,6 @@ static int fecmxc_probe(struct udevice *dev)
>> }
>>
>> fec_reg_setup(priv);
>> -
>> priv->dev_id = dev->seq;
>> #ifdef CONFIG_FEC_MXC_MDIO_BASE
>> bus = fec_get_miibus((ulong)CONFIG_FEC_MXC_MDIO_BASE,
>> dev->seq); @@ -1492,6 +1520,7 @@ static const struct udevice_id
>> fecmxc_ids[] = { { .compatible = "fsl,imx53-fec" },
>> { .compatible = "fsl,imx7d-fec" },
>> { .compatible = "fsl,mvf600-fec" },
>> + { .compatible = "fsl,imx8qm-fec" },
>
> Could you check if this patch doesn't break existing i.MX53, i.MX6q
> (mx53, mx6, mx7) by using buildman ?
>
> https://github.com/dsd/u-boot/tree/master/tools/buildman
>
I have run the buildman for mx53, mx6, mx7. No build break.
Best regards,
Ye Li
>> { }
>> };
>>
>> diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h
>> index e5f2dd7..23180a6 100644
>> --- a/drivers/net/fec_mxc.h
>> +++ b/drivers/net/fec_mxc.h
>> @@ -264,6 +264,7 @@ struct fec_priv {
>> u32 interface;
>> #endif
>> struct clk ipg_clk;
>> + struct clk ahb_clk;
>> u32 clk_rate;
>> };
>>
>
>
>
>
> Best regards,
>
> Lukasz Majewski
>
> --
>
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de
>
More information about the U-Boot
mailing list