[U-Boot] [PATCH v1 1/3] apalis-tk1: configs: remove legacy usbboot command

[Igor Opaniuk]

+ Oleksandr

On Tue, Jun 25, 2019 at 5:07 PM Igor Opaniuk <igor.opaniuk at toradex.com> wrote:
>
> Remove obsolete legacy usbboot wrapper, as distroboot can handle
> booting from USB drivers.
>
> Signed-off-by: Igor Opaniuk <igor.opaniuk at toradex.com>
> ---
>
>  include/configs/apalis-tk1.h | 19 -------------------
>  1 file changed, 19 deletions(-)
>
> diff --git a/include/configs/apalis-tk1.h b/include/configs/apalis-tk1.h
> index b4ddd1bdc6..cead0412cf 100644
> --- a/include/configs/apalis-tk1.h
> +++ b/include/configs/apalis-tk1.h
> @@ -90,23 +90,6 @@
>         "sdfinduuid=part uuid mmc ${sddev}:${sdrootpart} uuid\0" \
>         "sdrootpart=2\0"
>
> -#define USB_BOOTCMD \
> -       "set_usbargs=setenv usbargs ip=off root=PARTUUID=${uuid} ro " \
> -               "rootfstype=ext4 rootwait\0" \
> -       "usbboot=run setup; usb start; run usbfinduuid; run set_usbargs; " \
> -               "setenv bootargs ${defargs} ${setupargs} " \
> -               "${usbargs} ${vidargs}; echo Booting from USB stick...; " \
> -               "run usbdtbload; load usb ${usbdev}:${usbbootpart} " \
> -               "${kernel_addr_r} ${boot_file} && run fdt_fixup && " \
> -               "bootm ${kernel_addr_r} - ${dtbparam}\0" \
> -       "usbbootpart=1\0" \
> -       "usbdev=0\0" \
> -       "usbdtbload=setenv dtbparam; load usb ${usbdev}:${usbbootpart} " \
> -               "${fdt_addr_r} ${soc}-apalis-${fdt_board}.dtb " \
> -               "&& setenv dtbparam ${fdt_addr_r}\0" \
> -       "usbfinduuid=part uuid usb ${usbdev}:${usbrootpart} uuid\0" \
> -       "usbrootpart=2\0"
> -
>  #define BOARD_EXTRA_ENV_SETTINGS \
>         "boot_file=uImage\0" \
>         "console=ttyS0\0" \
> @@ -118,7 +101,6 @@
>         "fdt_fixup=;\0" \
>         NFS_BOOTCMD \
>         SD_BOOTCMD \
> -       USB_BOOTCMD \
>         "setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
>                 "00:14:2d:00:00:00; fi; pci enum && tftpboot ${loadaddr} " \
>                 "flash_eth.img && source ${loadaddr}\0" \
> @@ -135,7 +117,6 @@
>         "setusbupdate=usb start && setenv interface usb; setenv drive 0; " \
>                 "load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
>                 "source ${loadaddr}\0" \
> -       USB_BOOTCMD \
>         "vidargs=video=tegrafb0:640x480-16 at 60 fbcon=map:1\0"
>
>  /* Increase console I/O buffer size */
> --
> 2.17.1
>


-- 
Best regards - Freundliche Grüsse - Meilleures salutations

Senior Development Engineer,
Igor Opaniuk

Toradex AG
Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 48
00 (main line)