[U-Boot] [PATCH V2 51/51] imx: add i.MX8MN DDR4 board support

Lukasz Majewski lukma at denx.de
Wed Jul 10 12:18:42 UTC 2019


Hi Peng,

> > Subject: Re: [U-Boot] [PATCH V2 51/51] imx: add i.MX8MN DDR4 board
> > support
> >   
> [...]
> > > +
> > > MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x190  
> > 
> > Those changes looks identical. Why do you need to change those
> > lines? (Wrong formatting) ?  
> 
> Wrongly added. Drop in V3.
> 
> >   
> > >  		>;  
> > > +};  
> [...]
> >   
> > > diff --git a/arch/arm/dts/imx8mn-ddr4-evk.dts
> > > b/arch/arm/dts/imx8mn-ddr4-evk.dts new file mode 100644
> > > index 0000000000..9b2c1727a8
> > > --- /dev/null
> > > +++ b/arch/arm/dts/imx8mn-ddr4-evk.dts  
> > 
> > DTS files shall be added in a separate commit, to avoid one very
> > large one when you add the board.  
> 
> Fix in V3.
> 
> >   
> > > @@ -0,0 +1,221 @@
> > > +	{ 0x3d400498, 0x03ff0000 },
> > > +	{ 0x3d40049c, 0x01000e00 },
> > > +	{ 0x3d4004a0, 0x03ff0000 },
> > > +};  
> > 
> > Isn't there auto training code for i.MX8 as it is for i.MX6Q?
> > 
> > For example:
> > https://gitlab.denx.de/u-boot/u-boot/blob/master/arch/arm/mach-imx/mx6
> > /ddr.c
> > https://gitlab.denx.de/u-boot/u-boot/blob/master/arch/arm/mach-imx/ddr
> > mc-vf610-calibration.c  
> 
> The DDR FW will do auto training. 

Shouldn't there be any code to assist the training itself ?

> The DDR controller is
> complicated and different from i.MX6.

I guess that it has some capabilities to do the training in HW, the SW
only needs to feed input data and maybe start the process and check
results.

> 
> 
> > 
> >   
> > > +
> > > +/* PHY Initialize Configuration */
> > > +struct dram_cfg_param ddr_ddrphy_cfg[] = {
> > > +};  
> [....]
> > > +  
> > 
> > The list of binary data is quite impressive for i.MX8  
> 
> There are many many many registers in the DDRC in i.MX8M needs
> to configured.

First code for i.MX6 looked in a similar way. And after some time it
turned out that it could be written in C, not as a table of binary
blobs.

Is here also the similar situation?

Or to ask differently - isn't it possible to explain what your are
changing and for what purpose? 

> 
> >   
> > > +struct dram_fsp_msg ddr_dram_fsp_msg[] = {  
> [..]
> > > +{
> > > +	struct wdog_regs *wdog = (struct wdog_regs
> > > *)WDOG1_BASE_ADDR; +
> > > +	imx_iomux_v3_setup_multiple_pads(wdog_pads,  
> > 
> > Shouldn't those pins be configured via DTS/DM? As fair as I see
> > this is the imx8mn_evk.c file (which seems not to be the SPL).  
> 
> DM WDOG is not enabled here. 

If it is not enabled then the code shall be removed.

> Just use reset_cpu to do external reset

You shall use SYSRESET for that.

> 
> >   
> > > ARRAY_SIZE(wdog_pads)); +
> > > +	set_wdog_reset(wdog);
> > > +
> > > +	imx_iomux_v3_setup_multiple_pads(uart_pads,
> > > ARRAY_SIZE(uart_pads)); +
> > > +	init_uart_clk(1);  
> > 
> > This also seems like not DM/DTS code.  
> 
> We not enable DM UART.

This is u-boot proper, so DM UART shall be enabled.

> 
> >   
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +#ifdef CONFIG_BOARD_POSTCLK_INIT
> > > +int board_postclk_init(void)
> > > +{
> > > +	/* TODO */
> > > +	return 0;
> > > +}
> > > +#endif
> > > +
> > > +int dram_init(void)
> > > +{
> > > +	/* rom_pointer[1] contains the size of TEE occupies */
> > > +	if (rom_pointer[1])
> > > +		gd->ram_size = PHYS_SDRAM_SIZE - rom_pointer[1];
> > > +	else
> > > +		gd->ram_size = PHYS_SDRAM_SIZE;
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +#ifdef CONFIG_OF_BOARD_SETUP
> > > +int ft_board_setup(void *blob, bd_t *bd)
> > > +{
> > > +	return 0;
> > > +}
> > > +#endif
> > > +
> > > +int board_init(void)
> > > +{
> > > +	return 0;
> > > +}
> > > +
> > > +int board_mmc_get_env_dev(int devno)
> > > +{
> > > +	return devno - 1;
> > > +}  
> > 
> > Shouldn't the number of mmc device be get via alias defined in DTS
> > (or assigned automatically)?
> > 
> > What is the purpose of this function?  
> 
> mmc_get_env_dev will call this function. devno is the controller index

Why do you need the index if you have DM_MMC enabled? The struct device
shall be enough to perform all the necessary operations.

> inside SoC, however not every controller is enabled in a board.

I may be wrong, but this shall not be needed in DM_MMC supporting board.

> 
> >   
> > > +
> > > +int board_late_init(void)
> > > +{
> > > +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> > > +	env_set("board_name", "DDR4 EVK");
> > > +	env_set("board_rev", "iMX8MN");
> > > +#endif
> > > +	return 0;
> > > +}
> > > diff --git a/board/freescale/imx8mn_evk/spl.c
> > > b/board/freescale/imx8mn_evk/spl.c new file mode 100644
> > > index 0000000000..aa5f37fde0
> > > --- /dev/null
> > > +++ b/board/freescale/imx8mn_evk/spl.c
> > > @@ -0,0 +1,90 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * Copyright 2019 NXP
> > > + */
> > > +
> > > +#include <common.h>
> > > +#include <spl.h>
> > > +#include <asm/io.h>
> > > +#include <errno.h>
> > > +#include <asm/arch/imx8mn_pins.h>
> > > +#include <asm/arch/sys_proto.h>
> > > +#include <asm/arch/clock.h>
> > > +#include <asm/gpio.h>
> > > +#include <asm/arch/ddr.h>
> > > +#include <asm/mach-imx/boot_mode.h>
> > > +#include <asm/mach-imx/gpio.h>
> > > +#include <asm/mach-imx/iomux-v3.h>
> > > +#include <asm/mach-imx/mxc_i2c.h>
> > > +
> > > +#include <dm/uclass.h>
> > > +#include <dm/device.h>
> > > +#include <dm/uclass-internal.h>
> > > +#include <dm/device-internal.h>
> > > +
> > > +DECLARE_GLOBAL_DATA_PTR;
> > > +
> > > +int spl_board_boot_device(enum boot_device boot_dev_spl)
> > > +{
> > > +	return BOOT_DEVICE_BOOTROM;
> > > +}
> > > +
> > > +void spl_dram_init(void)
> > > +{
> > > +	ddr_init(&dram_timing);
> > > +}
> > > +
> > > +void spl_board_init(void)
> > > +{
> > > +	struct udevice *dev;
> > > +
> > > +	puts("Normal Boot\n");
> > > +
> > > +	uclass_find_first_device(UCLASS_CLK, &dev);
> > > +
> > > +	for (; dev; uclass_find_next_device(&dev)) {
> > > +		if (device_probe(dev))
> > > +			continue;  
> > 
> > Is this correct that in the SPL you call probe on all UCLASS_CLK
> > devices registered for i.MX8?  
> 
> Any issue you forseen?

It is just identical to what CCF is doing :-)

> 
> >   
> > > +	}
> > > +}
> > > +
> > > +#ifdef CONFIG_SPL_LOAD_FIT
> > > +int board_fit_config_name_match(const char *name)
> > > +{
> > > +	/* Just empty function now - can't decide what to choose
> > > */
> > > +	debug("%s: %s\n", __func__, name);
> > > +
> > > +	return 0;
> > > +}
> > > +#endif
> > > +
> > > +void board_init_f(ulong dummy)
> > > +{
> > > +	int ret;
> > > +
> > > +	arch_cpu_init();
> > > +
> > > +	init_uart_clk(1);
> > > +
> > > +	board_early_init_f();
> > > +
> > > +	timer_init();
> > > +
> > > +	preloader_console_init();
> > > +
> > > +	/* Clear the BSS. */
> > > +	memset(__bss_start, 0, __bss_end - __bss_start);
> > > +
> > > +	ret = spl_init();
> > > +	if (ret) {
> > > +		debug("spl_init() failed: %d\n", ret);
> > > +		hang();
> > > +	}
> > > +
> > > +	enable_tzc380();
> > > +
> > > +	/* DDR initialization */
> > > +	spl_dram_init();
> > > +
> > > +	board_init_r(NULL, 0);
> > > +}
> > > diff --git a/configs/imx8mn_ddr4_evk_defconfig
> > > b/configs/imx8mn_ddr4_evk_defconfig new file mode 100644
> > > index 0000000000..01e10fc427
> > > --- /dev/null
> > > +++ b/configs/imx8mn_ddr4_evk_defconfig
> > > @@ -0,0 +1,53 @@
> > > +CONFIG_ARM=y
> > > +CONFIG_ARCH_IMX8M=y
> > > +CONFIG_SYS_TEXT_BASE=0x40200000
> > > +CONFIG_SPL_GPIO_SUPPORT=y
> > > +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> > > +CONFIG_SPL_LIBGENERIC_SUPPORT=y
> > > +CONFIG_SYS_MALLOC_F_LEN=0x6000
> > > +CONFIG_TARGET_IMX8MN_EVK=y
> > > +CONFIG_SPL_SERIAL_SUPPORT=y
> > > +CONFIG_SPL=y
> > > +CONFIG_IMX_ROMAPI_LOADADDR=0x48000000
> > > +CONFIG_FIT=y
> > > +CONFIG_FIT_EXTERNAL_OFFSET=0x3000
> > > +CONFIG_SPL_LOAD_FIT=y
> > > +CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
> > >  
> > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/imx8m
> > /imximage-8mn-ddr4.cfg"  
> > > +CONFIG_DEFAULT_FDT_FILE="fsl-imx8mn-ddr4-evk.dtb"
> > > +CONFIG_SPL_TEXT_BASE=0x912000
> > > +CONFIG_SPL_BOARD_INIT=y
> > > +CONFIG_SPL_BOOTROM_SUPPORT=y
> > > +CONFIG_SPL_SEPARATE_BSS=y
> > > +CONFIG_SPL_I2C_SUPPORT=y
> > > +CONFIG_HUSH_PARSER=y
> > > +CONFIG_CMD_CLK=y
> > > +CONFIG_CMD_GPIO=y
> > > +CONFIG_CMD_I2C=y
> > > +CONFIG_CMD_CACHE=y
> > > +CONFIG_CMD_REGULATOR=y
> > > +CONFIG_CMD_EXT2=y
> > > +CONFIG_CMD_EXT4=y
> > > +CONFIG_CMD_EXT4_WRITE=y
> > > +CONFIG_CMD_FAT=y
> > > +CONFIG_OF_CONTROL=y
> > > +CONFIG_SPL_OF_CONTROL=y
> > > +CONFIG_DEFAULT_DEVICE_TREE="imx8mm-evk"
> > > +CONFIG_SPL_DM=y
> > > +CONFIG_SPL_CLK=y
> > > +CONFIG_CLK_IMX8MN=y
> > > +CONFIG_DM_GPIO=y
> > > +CONFIG_MXC_GPIO=y
> > > +CONFIG_DM_I2C=y
> > > +CONFIG_SYS_I2C_MXC=y
> > > +CONFIG_DM_MMC=y
> > > +CONFIG_PHYLIB=y
> > > +CONFIG_DM_ETH=y
> > > +CONFIG_PINCTRL=y
> > > +CONFIG_SPL_PINCTRL=y
> > > +CONFIG_PINCTRL_IMX8M=y
> > > +CONFIG_DM_REGULATOR=y
> > > +CONFIG_DM_REGULATOR_FIXED=y
> > > +CONFIG_DM_REGULATOR_GPIO=y
> > > +CONFIG_MXC_UART=y
> > > +CONFIG_DM_THERMAL=y  
> > 
> > You could also from the beginning enable CONFIG_WDT and
> > CONFIG_SYSRESET
> > (as i.MX6 already uses it).  
> 
> I'll try.
> 
> >   
> > > diff --git a/include/configs/imx8mn_evk.h
> > > b/include/configs/imx8mn_evk.h new file mode 100644
> > > index 0000000000..6ec8a2e362
> > > --- /dev/null
> > > +++ b/include/configs/imx8mn_evk.h
> > > @@ -0,0 +1,198 @@
> > > +/* SPDX-License-Identifier: GPL-2.0+ */
> > > +/*
> > > + * Copyright 2018 NXP
> > > + */
> > > +
> > > +#ifndef __IMX8MN_EVK_H
> > > +#define __IMX8MN_EVK_H
> > > +
> > > +#include <linux/sizes.h>
> > > +#include <asm/arch/imx-regs.h>
> > > +
> > > +#ifdef CONFIG_SECURE_BOOT
> > > +#define CONFIG_CSF_SIZE			0x2000 /* 8K
> > > region */ +#endif
> > > +
> > > +#define CONFIG_SPL_MAX_SIZE		(148 * 1024)
> > > +#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
> > > +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
> > > +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
> > > +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
> > > +#define CONFIG_SYS_UBOOT_BASE	\
> > > +	(QSPI0_AMBA_BASE +  
> > CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR *  
> > > 512) +
> > > +#ifdef CONFIG_SPL_BUILD
> > > +/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
> > > +#define CONFIG_SPL_WATCHDOG_SUPPORT
> > > +#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
> > > +#define CONFIG_SPL_POWER_SUPPORT
> > > +#define
> > > CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
> > > +#define CONFIG_SPL_STACK		0x95fff0 +#define
> > > CONFIG_SPL_BSS_START_ADDR	0x00950000 +#define
> > > CONFIG_SPL_BSS_MAX_SIZE		0x2000	/* 8 KB */  
> > 
> > Please fix globally -> replace 0x2000 -> SZ_8K from
> > include/linux/sizes.h  
> 
> Fix in V3.
> 
> >   
> > > +#define CONFIG_SYS_SPL_MALLOC_START	0x42200000 +#define
> > > CONFIG_SYS_SPL_MALLOC_SIZE	0x80000	/* 64 KB */
> > > +#define CONFIG_SYS_ICACHE_OFF +#define CONFIG_SYS_DCACHE_OFF
> > > +
> > > +/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
> > > +#define CONFIG_MALLOC_F_ADDR		0x00940000
> > > +
> > > +/* For RAW image gives a error info not panic */
> > > +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
> > > +
> > > +#undef CONFIG_DM_MMC
> > > +#undef CONFIG_DM_PMIC
> > > +#undef CONFIG_DM_PMIC_PFUZE100
> > > +
> > > +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> > > +
> > > +#endif
> > > +
> > > +#define CONFIG_REMAKE_ELF
> > > +
> > > +#define CONFIG_BOARD_EARLY_INIT_F
> > > +#define CONFIG_BOARD_POSTCLK_INIT
> > > +#define CONFIG_BOARD_LATE_INIT
> > > +
> > > +/* Flat Device Tree Definitions */
> > > +#define CONFIG_OF_BOARD_SETUP
> > > +
> > > +#undef CONFIG_CMD_EXPORTENV
> > > +#undef CONFIG_CMD_IMPORTENV
> > > +#undef CONFIG_CMD_IMLS
> > > +
> > > +#undef CONFIG_CMD_CRC32
> > > +#undef CONFIG_BOOTM_NETBSD
> > > +
> > > +/* Initial environment variables */
> > > +#define CONFIG_EXTRA_ENV_SETTINGS		\
> > > +	"script=boot.scr\0" \
> > > +	"image=Image\0" \
> > > +	"console=ttymxc1,115200
> > > earlycon=ec_imx6q,0x30890000,115200\0" \
> > > +	"fdt_addr=0x43000000\0"			\
> > > +	"fdt_high=0xffffffffffffffff\0"		\
> > > +	"boot_fdt=try\0" \
> > > +	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
> > > +	"initrd_addr=0x43800000\0"		\
> > > +	"initrd_high=0xffffffffffffffff\0" \
> > > +	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
> > > +	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART)
> > > "\0" \
> > > +	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
> > > +	"mmcautodetect=yes\0" \
> > > +	"mmcargs=setenv bootargs console=${console}
> > > root=${mmcroot}\0 " \
> > > +	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart}
> > > ${loadaddr} ${script};\0" \
> > > +	"bootscript=echo Running bootscript from mmc ...; " \
> > > +		"source\0" \
> > > +	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr}
> > > ${image}\0" \
> > > +	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr}
> > > ${fdt_file}\0" \
> > > +	"mmcboot=echo Booting from mmc ...; " \
> > > +		"run mmcargs; " \
> > > +		"if test ${boot_fdt} = yes || test ${boot_fdt} =
> > > try; then " \
> > > +			"if run loadfdt; then " \
> > > +				"booti ${loadaddr} -
> > > ${fdt_addr}; " \  
> > 
> > Please correct me if I'm wrong, but why do you use 'booti' (and
> > presumably boot Image?).
> > 
> > Please use fitImage (in think that it is mature enough to be used
> > for new ports - other imx SoCs use it already for some time);
> > 
> > It can be called as: bootm ${loadaddr}#conf@${fdt_conf}  
> 
> No. We not switch to FIT when uboot booting kernel.

This is strange. I can understand your objection to FitImage when you
wrap u-boot (to allow security IP block to calculate the checksum
effectively as it needs the proper image format).

However, I don't see any issues why you cannot use fitImage for booting
plain kernel.

Are there any technical difficulties for doing that? Do you have any
extra requirements ?

> 
> > 
> >   
> > > +			"else " \
> > > +				"echo WARN: Cannot load the DT;
> > > " \
> > > +			"fi; " \
> > > +		"else " \
> > > +			"echo wait for boot; " \
> > > +		"fi;\0" \
> > > +	"netargs=setenv bootargs console=${console} " \
> > > +		"root=/dev/nfs " \
> > > +		"ip=dhcp
> > > nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
> > > +	"netboot=echo Booting from net ...; " \
> > > +		"run netargs;  " \
> > > +		"if test ${ip_dyn} = yes; then " \
> > > +			"setenv get_cmd dhcp; " \
> > > +		"else " \
> > > +			"setenv get_cmd tftp; " \
> > > +		"fi; " \
> > > +		"${get_cmd} ${loadaddr} ${image}; " \
> > > +		"if test ${boot_fdt} = yes || test ${boot_fdt} =
> > > try; then " \
> > > +			"if ${get_cmd} ${fdt_addr} ${fdt_file};
> > > then " \
> > > +				"booti ${loadaddr} -
> > > ${fdt_addr}; " \
> > > +			"else " \
> > > +				"echo WARN: Cannot load the DT;
> > > " \
> > > +			"fi; " \
> > > +		"else " \
> > > +			"booti; " \
> > > +		"fi;\0"
> > > +
> > > +#define CONFIG_BOOTCOMMAND \
> > > +	   "mmc dev ${mmcdev}; if mmc rescan; then " \
> > > +		   "if run loadbootscript; then " \
> > > +			   "run bootscript; " \
> > > +		   "else " \
> > > +			   "if run loadimage; then " \
> > > +				   "run mmcboot; " \
> > > +			   "else run netboot; " \
> > > +			   "fi; " \
> > > +		   "fi; " \
> > > +	   "else booti ${loadaddr} - ${fdt_addr}; fi"
> > > +
> > > +/* Link Definitions */
> > > +#define CONFIG_LOADADDR			0x40480000
> > > +
> > > +#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
> > > +
> > > +#define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
> > > +#define CONFIG_SYS_INIT_RAM_SIZE        0x80000
> > > +#define CONFIG_SYS_INIT_SP_OFFSET \
> > > +	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> > > +#define CONFIG_SYS_INIT_SP_ADDR \
> > > +	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> > > +
> > > +#define CONFIG_ENV_OVERWRITE
> > > +#if defined(CONFIG_ENV_IS_IN_MMC)
> > > +#define CONFIG_ENV_OFFSET               (64 * SZ_64K)
> > > +#endif
> > > +#define CONFIG_ENV_SIZE			0x1000
> > > +#define CONFIG_SYS_MMC_ENV_DEV		0   /* USDHC2 */
> > > +#define
> > > CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2
> > > */ + +/* Size of malloc() pool */
> > > +#define CONFIG_SYS_MALLOC_LEN		SZ_32M
> > > +
> > > +#define CONFIG_SYS_SDRAM_BASE           0x40000000
> > > +#define PHYS_SDRAM                      0x40000000
> > > +#define PHYS_SDRAM_SIZE			0x80000000 /* 2GB
> > > DDR */ +
> > > +#define CONFIG_SYS_MEMTEST_START    PHYS_SDRAM
> > > +#define CONFIG_SYS_MEMTEST_END  
> > (CONFIG_SYS_MEMTEST_START +  
> > > (PHYS_SDRAM_SIZE >> 1)) +
> > > +#define CONFIG_BAUDRATE			115200
> > > +
> > > +#define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR
> > > +
> > > +/* Monitor Command Prompt */
> > > +#undef CONFIG_SYS_PROMPT
> > > +#define CONFIG_SYS_PROMPT		"u-boot=> "
> > > +#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
> > > +#define CONFIG_SYS_CBSIZE		2048
> > > +#define CONFIG_SYS_MAXARGS		64
> > > +#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
> > > +#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
> > > +
> > > sizeof(CONFIG_SYS_PROMPT) + 16) +
> > > +#define CONFIG_IMX_BOOTAUX  
> > 
> > Has the i.MX8 the use case for IMX_BOOTAUX - if not please remove
> > it.  
> 
> 
> i.MX8M use bootaux to kick M4

Ok.

> 
> >   
> > > +
> > > +/* USDHC */
> > > +#define CONFIG_CMD_MMC
> > > +#define CONFIG_FSL_ESDHC
> > > +#define CONFIG_FSL_USDHC
> > > +
> > > +#define CONFIG_SYS_FSL_USDHC_NUM	2
> > > +#define CONFIG_SYS_FSL_ESDHC_ADDR	0  
> > 
> > Some of the above are in Kconfig.
> >   
> > > +
> > > +#define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
> > > +#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
> > > +
> > > +#define CONFIG_CMD_FUSE
> > > +
> > > +#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus
> > > 1 */ +#define CONFIG_SYS_I2C_MXC_I2C2		/* enable
> > > I2C bus 2 */ +#define CONFIG_SYS_I2C_MXC_I2C3		/*
> > > enable I2C bus 3 */  
> >   
> > > +#define CONFIG_SYS_I2C_SPEED		100000  
> > 
> > Those #defines (I2C related) are already supported in Kconfig.
> > Please use them.
> > 
> > 
> > Please review above defines and move to Kconfig.  
> 
> Sure.
> 
> Thanks,
> Peng.
> 
> >   
> > > +
> > > +#define CONFIG_OF_SYSTEM_SETUP
> > > +#endif  
> > 
> > 
> > 
> > 
> > Best regards,
> > 
> > Lukasz Majewski
> > 
> > --
> > 
> > DENX Software Engineering GmbH,      Managing Director: Wolfgang
> > Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell,
> > Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
> > lukma at denx.de  




Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190710/1630b913/attachment.sig>


More information about the U-Boot mailing list