[U-Boot] [PATCH 2/2] configs: ls1028aqds: enable I2C and GPIO DM
Alex Marginean
alexandru.marginean at nxp.com
Fri Jul 12 11:23:20 UTC 2019
LS1028A was already converted to I2C/GPIO DM, move the QDS board over too.
Signed-off-by: Alex Marginean <alexm.osslist at gmail.com>
---
configs/ls1028aqds_tfa_SECURE_BOOT_defconfig | 5 ++++-
configs/ls1028aqds_tfa_defconfig | 5 ++++-
2 files changed, 8 insertions(+), 2 deletions(-)
diff --git a/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig b/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig
index 4a2b354008..76c9af5ef3 100644
--- a/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig
+++ b/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARM=y
CONFIG_TARGET_LS1028AQDS=y
+CONFIG_SYS_MALLOC_F_LEN=0x6000
CONFIG_SECURE_BOOT=y
CONFIG_SYS_FSL_SDHC_CLK_DIV=1
CONFIG_TFABOOT=y
@@ -8,7 +9,6 @@ CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
CONFIG_AHCI=y
CONFIG_DISTRO_DEFAULTS=y
-# CONFIG_SYS_MALLOC_F is not set
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
@@ -31,6 +31,9 @@ CONFIG_NETCONSOLE=y
CONFIG_DM=y
CONFIG_SCSI_AHCI=y
CONFIG_SATA_CEVA=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
diff --git a/configs/ls1028aqds_tfa_defconfig b/configs/ls1028aqds_tfa_defconfig
index b315910414..7c98474d73 100644
--- a/configs/ls1028aqds_tfa_defconfig
+++ b/configs/ls1028aqds_tfa_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARM=y
CONFIG_TARGET_LS1028AQDS=y
+CONFIG_SYS_MALLOC_F_LEN=0x6000
CONFIG_SYS_FSL_SDHC_CLK_DIV=1
CONFIG_TFABOOT=y
CONFIG_NR_DRAM_BANKS=2
@@ -7,7 +8,6 @@ CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
CONFIG_AHCI=y
CONFIG_DISTRO_DEFAULTS=y
-# CONFIG_SYS_MALLOC_F is not set
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
@@ -34,6 +34,9 @@ CONFIG_DM=y
CONFIG_SCSI_AHCI=y
CONFIG_SATA_CEVA=y
CONFIG_FSL_CAAM=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
--
2.17.1
More information about the U-Boot
mailing list