[U-Boot] [PATCH 2/2] configs: ls1028aqds: enable I2C and GPIO DM

[Chuanhua Han]

Hi,Alex

I have already sent the patch set of ls1028aqds i2c dm. Please check the patchwork link below：
https://patchwork.ozlabs.org/project/uboot/list/?series=118709

thanks,
Chaunhua
> -----Original Message-----
> From: Alex Marginean <alexandru.marginean at nxp.com>
> Sent: 2019年7月12日 19:23
> To: u-boot at lists.denx.de
> Cc: Chuanhua Han <chuanhua.han at nxp.com>; Prabhakar Kushwaha
> <prabhakar.kushwaha at nxp.com>; Alex Marginean <alexm.osslist at gmail.com>
> Subject: [PATCH 2/2] configs: ls1028aqds: enable I2C and GPIO DM
> 
> LS1028A was already converted to I2C/GPIO DM, move the QDS board over too.
> 
> Signed-off-by: Alex Marginean <alexm.osslist at gmail.com>
> ---
>  configs/ls1028aqds_tfa_SECURE_BOOT_defconfig | 5 ++++-
>  configs/ls1028aqds_tfa_defconfig             | 5 ++++-
>  2 files changed, 8 insertions(+), 2 deletions(-)
> 
> diff --git a/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig
> b/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig
> index 4a2b354008..76c9af5ef3 100644
> --- a/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig
> +++ b/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig
> @@ -1,5 +1,6 @@
>  CONFIG_ARM=y
>  CONFIG_TARGET_LS1028AQDS=y
> +CONFIG_SYS_MALLOC_F_LEN=0x6000
>  CONFIG_SECURE_BOOT=y
>  CONFIG_SYS_FSL_SDHC_CLK_DIV=1
>  CONFIG_TFABOOT=y
> @@ -8,7 +9,6 @@ CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
>  CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
>  CONFIG_AHCI=y
>  CONFIG_DISTRO_DEFAULTS=y
> -# CONFIG_SYS_MALLOC_F is not set
>  CONFIG_FIT_VERBOSE=y
>  CONFIG_OF_BOARD_SETUP=y
>  CONFIG_OF_STDOUT_VIA_ALIAS=y
> @@ -31,6 +31,9 @@ CONFIG_NETCONSOLE=y
>  CONFIG_DM=y
>  CONFIG_SCSI_AHCI=y
>  CONFIG_SATA_CEVA=y
> +CONFIG_DM_GPIO=y
> +CONFIG_DM_I2C=y
> +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
>  CONFIG_DM_MMC=y
>  CONFIG_FSL_ESDHC=y
>  CONFIG_DM_SPI_FLASH=y
> diff --git a/configs/ls1028aqds_tfa_defconfig
> b/configs/ls1028aqds_tfa_defconfig
> index b315910414..7c98474d73 100644
> --- a/configs/ls1028aqds_tfa_defconfig
> +++ b/configs/ls1028aqds_tfa_defconfig
> @@ -1,5 +1,6 @@
>  CONFIG_ARM=y
>  CONFIG_TARGET_LS1028AQDS=y
> +CONFIG_SYS_MALLOC_F_LEN=0x6000
>  CONFIG_SYS_FSL_SDHC_CLK_DIV=1
>  CONFIG_TFABOOT=y
>  CONFIG_NR_DRAM_BANKS=2
> @@ -7,7 +8,6 @@ CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
>  CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
>  CONFIG_AHCI=y
>  CONFIG_DISTRO_DEFAULTS=y
> -# CONFIG_SYS_MALLOC_F is not set
>  CONFIG_FIT_VERBOSE=y
>  CONFIG_OF_BOARD_SETUP=y
>  CONFIG_OF_STDOUT_VIA_ALIAS=y
> @@ -34,6 +34,9 @@ CONFIG_DM=y
>  CONFIG_SCSI_AHCI=y
>  CONFIG_SATA_CEVA=y
>  CONFIG_FSL_CAAM=y
> +CONFIG_DM_GPIO=y
> +CONFIG_DM_I2C=y
> +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
>  CONFIG_DM_MMC=y
>  CONFIG_FSL_ESDHC=y
>  CONFIG_DM_SPI_FLASH=y
> --
> 2.17.1